View MSDS : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION
Product Name: Premium Deck, Fence & Siding 2 in 1 Wood Prep No. 63-
N
Product Code: 63-N
MSDS Manufacturer 63-N
Number:
HMIS
Manufacturer Name: BEHR Process Corporation
Address: 3400 W. Segerstrom Avenue
Health Hazard 3
Santa Ana, CA 92704
General Phone Number: (714) 545-7101
Fire Hazard 1
General Fax Number: (714) 241-1002
Customer Service Phone (800) 854-0133 ext. 2 REACTIVITY 2
Number:
Personal
CHEMTREC: For emergencies in the US, call CHEMTREC: 800-424-9300 x
Protection
Canutec: In Canada, call CANUTEC: (613) 996-6666 (call collect)
* Chronic Health
MSDS Creation Date: 06/26/2006
Effects:
MSDS Revision Date: 2/20/2009
SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS# Ingredient Percent
Undisclosed/Proprietary No data 60 - 100 by weight
Sodium octanesulfonate 5324-84-5 1 - 5 by weight
Proprietary Enzyme Formula No data 5 - 10 by weight
Oxalic acid 144-62-7 10 - 30 by weight
Isopropyl alcohol 67-63-0 0.1 - 1 by weight
Non hazardous ingredient(s) No data 5 - 10 by weight
SECTION 3 - HAZARDS IDENTIFICATION
Emergency Overview: Corrosive. Irritant.
Potential Health Effects:
Eye: Corrosive. Will cause eye burns and permanent tissue damage.
Skin: Severely irritating; may cause permanent skin damage.
Inhalation: May cause severe respiratory system irritation.
Ingestion: Harmful if swallowed. Corrosive to the gastrointestinal tract.
Chronic Health Effects: Prolonged skin contact causes burns.
Repeated or prolonged inhalation may cause toxic effects.
Signs/Symptoms: Depending on solution concentration, material may be corrosive to skin, mucous
membranes and eyes. Vapors may cause respiratory irritation.
Target Organs: Eyes. Skin. Respiratory system. Digestive system.
Aggravation of Pre-Existing May aggravate pre-existing respiratory disorders, allergy, eczema, or skin
Conditions: conditions.
SECTION 4 - FIRST AID MEASURES
Eye Contact: Immediately flush eyes with plenty of water for 15 to 20 minutes. Get medical
attention, if irritation or symptoms of overexposure persists.
Skin Contact: Immediately wash skin with plenty of soap and water for 15 to 20 minutes, while
removing contaminated clothing and shoes.
Get medical attention if irritation develops or persists.
Inhalation: If inhaled, remove to fresh air. If not breathing, give artificial respiration or give
oxygen by trained personnel. Seek immediate medical attention.
Ingestion: If swallowed, do NOT induce vomiting. Call a physician or poison control center
immediately. Never give anything by mouth to an unconscious person.
Other First Aid: Due to possible aspiration into the lungs, DO NOT induce vomiting if ingested.
Provide a glass of water to dilute the material in the stomach. If vomiting occurs
naturally, have the person lean forward to reduce the risk of aspiration.
SECTION 5 - FIRE FIGHTING MEASURES
Flash Point: No Data
Lower Flammable/Explosive Limit: Not applicable.
Upper Flammable/Explosive Limit: Not applicable.
Extinguishing Media: Use alcohol resistant foam, carbon dioxide, dry chemical, or water fog or spray
when fighting fires involving this material.
Protective Equipment: As in any fire, wear Self-Contained Breathing Apparatus (SCBA), MSHA/NIOSH
(approved or equivalent) and full protective gear.
NFPA Ratings:
NFPA Flammability: 1
NFPA Health: 3
NFPA Reactivity: 2
SECTION 6 - ACCIDENTAL RELEASE MEASURES
Personnel Precautions: Corrosive. Use proper personal protective equipment as listed in section 8.
Environmental Precautions: Avoid runoff into storm sewers, ditches, and waterways.
Spill Cleanup Measures: Neutralize residue with appropriate neutralizer. Do not attempt to neutralize
large quantities of material unless measures to control reactivity and heat
generation have been taken. Absorb spill with inert material (e.g.., dry sand or
earth), then place in a chemical waste container. Provide ventilation.
SECTION 7 - HANDLING and STORAGE
Handling: Use with adequate ventilation. Avoid breathing vapor and contact with eyes, skin
and clothing. Corrosive. Use proper personal protective equipment as listed in
section 8.
Storage: Store in a cool, dry, well ventilated area away from sources of heat, combustible
materials, and incompatible substances. Keep container tightly closed when not
in use.
Hygiene Practices: Wash thoroughly after handling. Avoid contact with eyes and skin. Avoid inhaling
vapor or mist.
SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION - EXPOSURE GUIDELINES
Engineering Controls: Use appropriate engineering control such as process enclosures, local exhaust
ventilation, or other engineering controls to control airborne levels below
recommended exposure limits. Good general ventilation should be sufficient to
control airborne levels. Where such systems are not effective wear suitable
personal protective equipment, which performs satisfactorily and meets OSHA or
other recognized standards. Consult with local procedures for selection, training,
inspection and maintenance of the personal protective equipment.
Eye/Face Protection: Wear appropriate protective glasses or splash goggles as described by 29 CFR
1910.133, OSHA eye and face protection regulation, or the European standard
EN 166.
Skin Protection Description: Chemical-resistant gloves and chemical goggles, face-shield and synthetic apron
or coveralls should be used to prevent contact with eyes, skin or clothing.
Respiratory Protection: A NIOSH approved air-purifying respirator with an organic vapor cartridge or
canister may be permissible under certain circumstances where airborne
concentrations are expected to exceed exposure limits. Protection provided by air
purifying respirators is limited. Use a positive pressure air supplied respirator if
there is any potential for an uncontrolled release, exposure levels are not known,
or any other circumstances where air purifying respirators may not provide
adequate protection.
Other Protective: Facilities storing or utilizing this material should be equipped with an eyewash
facility and a safety shower.
EXPOSURE GUIDELINES
Oxalic acid :
Guideline ACGIH: TLV-TWA: 1 mg/m3
TLV-STEL: 2 mg/m3
Guideline OSHA: OSHA-TWA: 1 mg/m3
Isopropyl alcohol :
Guideline ACGIH: TLV-TWA: 200 ppm
TLV-STEL: 400 ppm
Guideline OSHA: OSHA-TWA: 400 ppm
SECTION 9 - PHYSICAL and CHEMICAL PROPERTIES
Color: Hazy
Boiling Point: No Data
Melting Point: No Data
Density: 8 - 10 Lbs./gal.
Vapor Density: Greater than 1 (Air = 1).
pH: 1 to 2.5
Molecular Formula: Mixture
Molecular Weight: Mixture
Flash Point: No Data
VOC Content: Material VOC: 1 gm/l (Includes Water)
Coating VOC.: 7 gm/l (Excludes Water)
SECTION 10 - STABILITY and REACTIVITY
Chemical Stability: Stable under normal temperatures and pressures.
Hazardous Polymerization: Not reported.
Conditions to Avoid: Heat, flames, incompatible materials, freezing or temperatures below 32 deg. F.
Incompatible Materials: Oxidizing agents. Strong acids and alkalis.
SECTION 11 - TOXICOLOGICAL INFORMATION
Oxalic acid :
RTECS Number: RO2450000
Eye: Eye - Rabbit; Standard Draize Test. : 250 ug/24H; severe. (RTECS)
Skin: Skin - Rabbit; Standard Draize Test. : 500 mg/24H; mild. (RTECS)
Ingestion: Ingestion - Rat LD50: 7500 mg/kg; Details of toxic effects not reported other
than lethal dose value. . (RTECS)
Isopropyl alcohol :
RTECS Number: NT8050000
Eye: Eye - Rabbit; Standard Draize Test. : 100 mg; severe.
Eye - Rabbit; Standard Draize Test. : 100 mg/24H; Moderate. (RTECS)
Skin: Skin - Rabbit; Standard Draize Test. : 500 mg; mild. (RTECS)
Inhalation: Inhalation. - Rat LC50: 72600 mg/m3; Behavioral - general anesthetic Lungs,
Thorax, or Respiration - other changes
Inhalation. - Rat LC50: 16000 ppm/8H; Details of toxic effects not reported other
than lethal dose value.. (RTECS)
Ingestion: Ingestion - Rat LD50: 5000 mg/kg; Behavioral - general anesthetic
Ingestion - Mouse LD50: 3600 mg/kg - Behavioral - general anesthetic. (RTECS)
SECTION 12 - ECOLOGICAL INFORMATION
Ecotoxicity: No ecotoxicity data was found for the product.
Environmental Fate: No environmental information found for this product.
SECTION 13 - DISPOSAL CONSIDERATIONS
Waste Disposal: Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the
classifications of hazardous waste prior to disposal. Furthermore, consult with
your state and local waste requirements or guidelines, if applicable, to ensure
compliance. Arrange disposal in accordance to the EPA and/or state and local
guidelines.
SECTION 14 - TRANSPORT INFORMATION
DOT Shipping Name: Paint related material
DOT UN Number: UN3066
DOT Hazard Class: 8
DOT Packing Group: II
SECTION 15 - REGULATORY INFORMATION
Sodium octanesulfonate :
TSCA Inventory Status: Listed
Canada DSL: Listed
Oxalic acid :
TSCA Inventory Status: Listed
State Regulations: Listed in the New Jersey State Right to Know List.
Listed in the Pennsylvania State Hazardous Substances List.
Canada DSL: Listed
Isopropyl alcohol :
TSCA Inventory Status: Listed
State Regulations: Listed in the New Jersey State Right to Know List.
Listed in the Pennsylvania State Hazardous Substances List.
Canada DSL: Listed
SECTION 16 - ADDITIONAL INFORMATION
HMIS Fire Hazard: 1
HMIS Health Hazard: 3
HMIS Reactivity: 2
HMIS Personal Protection: x
MSDS Creation Date: 06/26/2006
MSDS Revision Date: 2/20/2009
MSDS Revision Notes: Name change.
MSDS Author: Actio Corporation
Disclaimer: This Health and Safety Information is correct to the best of our knowledge and
belief at the date of its publication but we cannot accept liability for any loss,
injury or damage which may result from its use. We shall ensure, so far as is
reasonably practicable, that any revision of this Data Sheet is sent to all
customers to whom we have directly supplied this substance, but must point out
that it is the responsibility of any intermediate supplier to ensure that such
revision is passed to the ultimate user. The information given in the Data Sheet
is designed only as a guidance for safe handling, storage and the use of the
substance. It is not a specification nor does it guarantee any specific properties.
All chemicals should be handled only by competent personnel, within a controlled
environment. Should further information be required, this can be obtained
through the sales office whose address is at the top of this data sheet.
Trademark: The trademarks, service marks, graphics and logos used on this MSDS are
registered or unregistered trademarks of BEHR Process Corporation. All Rights
Reserved.
Copyright?1996-2008 Actio Software Corporation. All Rights Reserved.
|