Material Safety Data Sheet CS: 1.4.22
1 of 4
Page:
LPXOG Issue Date :October 2008
Infosafe NoTM ISSUED by PENRITE CS: 1.4.22
Product Name :ATF MHP
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER
ATF MHP
Product Name
ATFMHP
Product Code
PENRITE OIL COMPANY P/L (ABN 25005 001 525)
Company Name
Address 88 Lewis Road Wantirna South
Victoria 3152 Australia
03 9801 0877 B.H
Emergency Tel.
Tel: 03 9801 0877
Telephone/Fax
Number
Automatic transmission fluid.
Recommended Use
2. HAZARDS IDENTIFICATION
HAZARDOUS SUBSTANCE.
Hazard
NON-DANGEROUS GOODS.
Classification
Hazard classification according to the criteria of NOHSC.
Dangerous goods classification according to the Australia Dangerous Goods
Code.
Risk Phrase(s) R36/38 Irritating to eyes and skin.
R43 May cause sensitization by skin contact.
R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in
the aquatic environment.
Safety Phrase(s) S2 Keep out of reach of children.
S24/25 Avoid contact with skin and eyes.
S37/39 Wear suitable gloves and eye/face protection.
S61 Avoid release to the environment. Refer to special instructions/safety
data sheet.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Name CAS Proportion
Ingredients
64742-54-7 >60-100 %
Distillates,
Hydrotreated
Heavy Paraffinic
1-<30 %
Alkyl
Thiophosphites
Diphenylamine 122-39-4 0-<1 %
N/A Balance
Other ingredients
determined not to
be hazardous
Other Information Note:
Ingredients that have been assigned Note L of the Worksafe designated List of
Hazardous Substances, have been tested in accordance with IP 346. This product
contains less than 3% polyaromatics and is therefore non hazardous.
4. FIRST AID MEASURES
Inhalation If inhaled, remove affected person from contaminated area. Apply artificial
respiration if not breathing. If symptoms develop seek medical attention.
Ingestion Do NOT induce vomiting. Wash out mouth with water. If symptoms develop seek
medical attention.
Skin Wash affected area thoroughly with soap and water. Remove contaminated
clothing and wash before reuse or discard. If symptoms develop seek medical
attention.
Eye If in eyes, hold eyelids apart and flush the eyes immediately with running
water. Continue flushing for several minutes until all contaminants are washed
off completely. Seek medical attention.
Eye wash and normal washroom facilities.
First Aid Facilities
Treat symptomatically.
Advice to Doctor
5. FIRE FIGHTING MEASURES
Print Date: 16/10/2008 CS: 1.4.22
Material Safety Data Sheet CS: 1.4.22
2 of 4
Page:
LPXOG Issue Date :October 2008
Infosafe NoTM ISSUED by PENRITE CS: 1.4.22
Product Name :ATF MHP
Carbon dioxide, dry chemical, foam and water fog.
Suitable
Extinguishing Media
Under fire conditions this product may emit toxic and/or irritating fumes
Hazards from
including smoke, carbon monoxide, carbon dioxide, oxides of sulphur and
Combustion
nitrogen.
Products
Combustible liquid.
Specific Hazards
Fire-fighters should wear full protective clothing and self contained
Precautions in
breathing apparatus (SCBA) operated in positive pressure mode. Water spray may
connection with Fire
be used to keep fire exposed containers cool.
6. ACCIDENTAL RELEASE MEASURES
Wear appropriate personal protective equipment and clothing to minimise
Emergency
exposure. Extinguish or remove all sources of ignition and stop leak if safe
Procedures
to do so. Increase ventilation. Evacuate all unprotected personnel. If
possible contain the spill. Spillage may be slippery. Place inert,
non-combustible absorbent material onto spillage. Use clean non-sparking tools
to collect the material and place into suitable labelled containers for the
subsequent recycling or disposal. Dispose of waste according to the applicable
local and national regulations. If contamination of sewers or waterways occurs
inform the local water authorities and EPA in accordance with local
regulations.
7. HANDLING AND STORAGE
Use in a well ventilated area. DO NOT store or use in confined spaces. Build
Precautions for Safe
up of mists or vapours in the atmosphere must be prevented. Avoid breathing in
Handling
spray or mists or vapours. Do not use near welding or other ignition sources
and avoid sparks. Do not smoke. When dealing with large quantities, repeated
or prolonged skin exposure without protection should be prevented in order to
lessen the possibility of skin disorders. Practice good personal hygiene, that
is, always wash hands after handling, and before eating, drinking, smoking or
using the toilet facilities.
Store in a cool, dry well-ventilated area away from heat, sources of ignition,
Conditions for Safe
oxidising agents, foodstuffs, and clothing and out of direct sunlight. Keep
Storage
containers closed when not in use and securely sealed and protected against
physical damage. Inspect regularly for deficiencies such as damage or leaks.
Do NOT pressurise, cut, heat or weld containers as they may contain hazardous
residues. For information on the design of the storeroom, reference should be
made to Australian Standard AS1940 - The storage and handling of flammable and
combustible liquids. Reference should also be made to all State and Federal
regulations.
Storage Regulations Classified as a Class C2 (COMBUSTIBLE LIQUID) for the purposes of storage and
handling, in accordance with the requirements of AS1940.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
No exposure standards have been established for this material, however, the
National Exposure
TWA National Occupational Health And Safety Commission (NOHSC) exposure
Standards
standards for oil mist is 5 mg/m? As with all chemicals, exposure should be
kept to the lowest possible levels.
TWA (Time Weighted Average): The average airborne concentration of a
particular substance when calculated over a normal eight-hour working day, for
a five-day week.
No biological limit allocated.
Biological Limit
Values
Provide sufficient ventilation to keep airborne levels below the exposure
Engineering
limit. Where vapours or mists are generated, particularly in enclosed areas,
Controls
and natural ventilation is inadequate, a local exhaust ventilation system is
required. Refer to AS1940 - The storage and handling of flammable and
combustible liquids and AS2430 - Explosive gas atmospheres for further
information concerning ventilation requirements.
If mists or vapours are generated and ventilation is inadequate, particularly
Respiratory
in enclosed areas then an approved respirator with a replaceable organic
Protection
vapour/mist filter is recommended. Final choice of appropriate breathing
protection is dependant upon actual airborne concentrations and the type of
breathing protection required will vary according to individual circumstances.
Print Date: 16/10/2008 CS: 1.4.22
Material Safety Data Sheet CS: 1.4.22
3 of 4
Page:
LPXOG Issue Date :October 2008
Infosafe NoTM ISSUED by PENRITE CS: 1.4.22
Product Name :ATF MHP
Expert advice may be required to make this decision. Reference should be made
to Australian Standards AS/NZS 1715, Selection, Use and maintenance of
Respiratory Protective Devices; and AS/NZS 1716, Respiratory Protective
Devices.
Eye Protection Safety glasses with side shields, goggles or full-face shield as appropriate
recommended. Final choice of appropriate eye/face protection will vary
according to individual circumstances i.e. methods of handling or engineering
controls and according to risk assessments undertaken. Eye protection should
conform with Australian/New Zealand Standard AS/NZS 1337 - Eye Protectors for
Industrial Applications.
Hand Protection Wear gloves of impervious material such as nitrile. Final choice of
appropriate gloves will vary according to individual circumstances i.e.
methods of handling or according to risk assessments undertaken. Reference
should be made to AS/NZS 2161.1: Occupational protective gloves - Selection,
use and maintenance.
Body Protection Wear appropriate clothing including chemical resistant apron where clothing is
likely to be contaminated. It is advisable that a local supplier of personal
protective clothing is consulted regarding the choice of material.
9. PHYSICAL AND CHEMICAL PROPERTIES
Red liquid
Appearance
Characterisitc odour
Odour
Not available
Freezing Point
Not available
Boiling Point
Insoluble
Solubility in Water
Not applicable
pH Value
Not available
Vapour Pressure
Not available
Vapour Density
(Air=1)
Viscosity 8.2 cSt at 100癈
38 cSt at 40癈
-42癈
Pour Point
0.852 at 15癈
Density
178癈
Flash Point
Combustible liquid
Flammability
Not available
Flammable Limits -
Lower
Not available
Flammable Limits -
Upper
10. STABILITY AND REACTIVITY
Stable under normal conditions of storage and handling.
Chemical Stability
Extreme heat
Conditions to Avoid
Strong oxidising agents
Incompatible
Materials
Thermal decomposition may result in the release of toxic and/or irritating
Hazardous
fumes including smoke, oxides of sulphur, carbon monoxide, carbon dioxide and
Decomposition
oxides of nitrogen.
Products
Will not occur.
Hazardous
Polymerization
11. TOXICOLOGICAL INFORMATION
No toxicology data available for this product. However, for product
Toxicology
components, the following data applies:
Information
Diphenylamine
LD50 (Oral, rat) : > 2 g/kg
Print Date: 16/10/2008 CS: 1.4.22
Material Safety Data Sheet CS: 1.4.22
4 of 4
Page:
LPXOG Issue Date :October 2008
Infosafe NoTM ISSUED by PENRITE CS: 1.4.22
Product Name :ATF MHP
LD50 (Dermal, rabbit) : >2 g/kg
LC50 (Inhalation, rat) : > 5mg/litre
Distillate, Hydrotreated Heavy Paraffines
LD50 (Oral, rat) : > 5 g/kg
LD50 (Dermal, rabbit) : >5 g/kg
Inhalation Inhalation of product vapours may cause irritation of the nose, throat and
respiratory system.
Ingestion Ingestion of this product may irritate the gastric tract causing nausea and
vomiting.
Skin Irritating to the skin. Can cause redness and itching. Exposure to hot
material will cause thermal burns. May cause sensitization by skin contact.
Eye irritant. Can cause tearing, stinging, blurred vision, and redness.
Eye
May cause sensitization by skin contact.
Chronic Effects
12. ECOLOGICAL INFORMATION
Ecotoxicity Harmful to aquatic organisms, may cause long-term adverse effects in the
aquatic environment. In addition, oil spills can smother and suffocate aquatic
life by preventing passage of oxygen into water. Oil contamination can also
foul and smother birds and marine animals.
Not available
Persistence /
Degradability
Insoluble in water. Expected to float.
Mobility
Not available
Bioaccumulative
Potential
Do not allow product to enter drains, waterways or sewers.
Environ. Protection
13. DISPOSAL CONSIDERATIONS
The disposal of the spilled or waste material must be done in accordance with
Disposal
applicable local and national regulations.
Considerations
14. TRANSPORT INFORMATION
Not classified as a Dangerous Good, according to the Australian Code for the
Transport
Transport of Dangerous Goods by Road and Rail.
Information
15. REGULATORY INFORMATION
Classified as Hazardous according to criteria of National Occupational Health
Regulatory
& Safety Commission (NOHSC), Australia.
Information
Not classified as a Scheduled Poison according to the Standard for the Uniform
Scheduling of Drugs and Poisons (SUSDP).
Not Scheduled
Poisons Schedule
Irritant
Hazard Category
16. OTHER INFORMATION
MSDS Prepared: September 2008
Date of preparation
or last revision of
MSDS
Contact Person/Point TITLE: Technical and Marketing Director
TELEPHONE NUMBER: 03 9801 0877 B.H
...End Of MSDS...
?Copyright ACOHS Pty Ltd
Copyright in the source code of the HTML, PDF, XML, XFO and any other electronic files rendered by an Infosafe system for Infosafe MSDS displayed on this site is the
intellectual property of Acohs Pty Ltd.
Copyright in the layout, presentation and appearance of each Infosafe MSDS displayed on this site is the intellectual property of Acohs Pty Ltd.
The compilation of MSDS's displayed on this site is the intellectual property of Acohs Pty Ltd.
Copying of any MSDS displayed on this site is permitted for personal use only and otherwise is not permitted. In particular the MSDS's displayed on this site cannot be
Print Date: 16/10/2008 CS: 1.4.22
|