Material Safety Data Sheet
Section 1: Product and Company Identification
Product Name: ACC 201 Quick Filler Part A (Pre-Polymer)
Sold By: Advantage Chemical Coatings LLC.
16585 N 92nd Street Suite 106
Scottsdale, Arizona 85260
877.830.COAT
Spill, leak, fire, exposure, or
FOR CHEMICAL
accident, call 24 hours
EMERGENCY
877.830.2628
Fax Phone: 480.502.9071
Section 2: Composition/Information on Ingredients
Hazardous Components CAS# ACGIH TLV OSHA PEL
Diphenylmethane Diisocyanate 101-68-8 Not Determined 02 ppm Cei
Propylene Carbonate 108-32-7 Not Determined Not Determined
Section 3: Hazards Identification
Emergency Overview:
Routes of Entry: Route Entry Risk
Possible
Inhalation
Possible
Ingestion
Skin Contact Possible
Eye Contact Possible
Potential Health Effects: Inhalation May cause nausea and respiratory tract irritation. May cause respiratory sensitization
in susceptible individuals.
Ingestion No significant signs or symptoms of any adverse health hazards.
Skin Contact Product is a slight skin irritant. May Cause swelling and redness.
Eye Contact Mild eye irritant. Vapors slightly uncomfortable. Splashes irritating and painful.
Acute Health Hazards: No information is available on the acute health hazards of this product. Based upon data from testing
of similar products, no significant effects are expected.
Chronic Health Hazards: If misted or at high concentrations, may cause pallor, nausea, anesthetic or narcotic effects.
Medical Conditions Skin and eye sensitization. Depending on individual skin sensitivity, chronic or prolonged exposure
Generally Aggravated by
may result in irritation, blistering, burning and peeling of skin layers.
Exposure:
Carcinogenicity: No data No data No data No data
OSHA: ACGIH: NTP: IARC:
Other:
Advantage Chemical Coatings ?010 ACC 201 MSDS
Rev: 02-08-08 Page 1 of 8
Section 4: First Aid Measures
Eye Contact: Immediately flush with plenty of water for at least 15 minutes. If redness, itching, or a burning
sensation develops, seek medical attention.
Skin Contact: Remove from skin immediately. Rinse with clean water for 20-30 minutes. Use soapy water if
needed. If redness, itching, or a burning sensation develops, seek medical attention.
Ingestion: Do NOT induce vomiting! Dilute with water and seek medical attention immediately.
Inhalation: Move victim to fresh air immediately. Give oxygen and seek medical attention.
Section 5: Fire-Fighting Measures
Flammable Limits: Not established
Flash Point, (Method Used): >200?Fahrenheit (Pensky-Marten Closed)
Autoignition Temperature:
NFPA Hazard Rating: Hazard Scale Protective Equipment
Health:
0=LEAST A=SAFETY GLASSES
Flammability:
1=SLIGHT B=SAFETY GLASSES, GLOVES
Reactivity: 2=MODERATE C=SAFETY GLASSES, GLOVES AND APRON
3=HIGH
Other: 4=EXTREME
HMIS Hazard Rating: Health:
Flammability:
Reactivity:
Protection:
Extinguishing Media: Foam/Carbon dioxide/Dry chemical/Water fog
Special Fire Fighting Remove all ignition sources. Wear self-contained breathing apparatus and complete personal
Procedures:
protective equipment when entering confined areas where potential for exposure to vapors or
products exist.
Unusual Fire and Explosion Closed containers may rupture due to build-up of pressure when exposed to extreme heat.
Hazards:
Hazardous Decomposition
Products:
Section 6: Accidental Release Measures
Accidental Release Avoid contact with material. Persons not wearing appropriate protective equipment should be
Measures:
excluded until the spill is cleaned up. Stop spill at source, pump liquid to salvage container.
Remaining liquid may be taken up by clay, diatomaceous earth, or other absorbent. Treat with 3-8%
concentration of ammonium hydroxide or 5-10% sodium carbonate. Add 10 parts neutralizing
solution/part isocyanate. Let stand 48 hours.
Section 7: Handling and Storage
Handling & Storage Prevent all skin and eye contact. Avoid breathing vapors. Re-seal partially used containers. Wash
Precautions:
with soap and water before eating or drinking. Protect from moisture contamination. Exothermic
generation of carbon dioxide may cause dangerous pressure. Keep away from all ignitable sources as
well as extreme heat. Do not expose to excessive moisture.
Section 8: Exposure Control/Personal Protection
Ventilation: Adequate ventilation required. Local exhaust may be required in some areas. Special exhausting
generally not required. Mechanical exhaust usually adequate.
Respiratory Protection: Respiratory masks should be worn at all times when adequate ventilation does not exist. A
NIOSH/MSHA respirator is acceptable.
Eye Protection: Chemical tight goggles; full face shield if splashing is possible.
Skin Protection: Coveralls and impervious foot covering is recommended.
Other Protective Clothing Use impervious gloves, neoprene or rubber.
or Equipment:
Work/Hygenic Practices: Good air flow in working area. Eyewash station and safety shower should be available. Gloves and
respiratory equipment should be worn at all times.
Advantage Chemical Coatings ?010 ACC 201 MSDS
Rev: 02-08-08 Page 2 of 8
Section 9: Physical and Chemical Properties
Pale yellow to amber
Appearance:
Faint odor
Odor:
Liquid
Physical State:
ph As Supplied:
ph (Other):
Boiling Point: No data
No data
Melting Point:
Freezing Point:
No data
Vapor Pressure (mmHg):
No data
Vapor Density (Air=1):
Specific Gravity (Water=1): 1.15
Evaporation Rate (Butyl
Slower than
Acetate=1):
Insoluble
Solubility in Water:
Percent Solids by Weight:
Percent Volatile: By Weight: By Volume:
Volatile Organic
With Water: Without Water:
Compounds (VOC):
Molecular Weight:
Viscosity:
Section 10: Stability and Reactivity
Stability: Stable
Conditions to Avoid excessive heat, open flam, sparks and strong oxidizing agents. Protect from atmospheric
Avoid (Stability):
moisture. Replace outage with inert dry nitrogen.
Incompatibility (Materials Avoid water, acid, base (alkalis, ammonia), alcohols, metal compounds.
to Avoid):
Hazardous Decomposition Isocyanate vapors or mist, carbon dioxide, carbon monoxide, nitrogen oxides.
or Byproducts:
Hazardous Polymerization: May occur
Conditions to Avoid Avoid incompatible reactants, especially strong bases, water or temperatures over 160?Centigrade.
(Polymerization):
Section 11: Toxicological Information
Toxicological Information: No Data
Section 12: Ecological Information
Ecological Information: No Data
Section 13: Disposal Considerations
Waste Disposal Method: Dispose of according to current local, state and federal regulations.
Non-Regulated
RCRA Hazard Class:
Advantage Chemical Coatings ?010 ACC 201 MSDS
Rev: 02-08-08 Page 3 of 8
Section 14: Transport Information
U.S. Department of Transportation
Proper Shipping Name: Polyisocyanate
Hazard Class: Non-regulated (in 55 gallon drums), NOI
ID Number:
Packing Group:
Label Statement:
Water Transportation
Proper Shipping Name:
Hazard Class: Non-regulated, NOI
ID Number:
Packing Group:
Label Statement:
Air Transportation
Proper Shipping Name:
Hazard Class: Non-regulated, NOI
ID Number:
Packing Group:
Label Statement:
Other Agencies:
Section 15: Regulatory Information
U.S. Federal Regulations
TSCA (Toxic Substance Control Act):
CERCLA (Comprehensive Response
Compensation and Liability Act):
SARA Title III (Superfund Amendments
and Reauthorization Act):
311/312 Hazard Categories:
313 Reportable Ingredients:
State Regulations:
International Regulations:
Section 16: Other Information
Other Information:
Preparation Information:
Disclaimer: This information is formulated for use by elements of the Department of Defense. The United States of America
in no manner whatsoever expressly or implied warrants, states, or intends said information to have any
application, use or viability by or to any person or persons outside the Department of Defense nor any person or
persons contracting with any instrumentality of the United States of America and disclaims all liability for such
use. Any person utilizing this instruction who is not a military or civilian employee of the United States of
America should seek competent professional advice to verify and assume responsibility for the suitability of this
information to their particular situation regardless of similarity to a corresponding Department of Defense or
other government situation.
Advantage Chemical Coatings ?010 ACC 201 MSDS
Rev: 02-08-08 Page 4 of 8
Material Safety Data Sheet
Section 1: Product and Company Identification
Product Name: ACC 201 Quick Filler Part B (Hardener)
Sold By: Advantage Chemical Coatings LLC.
16585 N 92nd Street Suite 106
Scottsdale, Arizona 85260
480-888-COAT
Spill, leak, fire, exposure, or
FOR CHEMICAL
accident, call 24 hours
EMERGENCY
877.830.2628
Fax Phone: 480.502.9071
Section 2: Composition/Information on Ingredients
Hazardous Components CAS# ACGIH TLV OSHA PEL
Polyoxyalkyleneamine 9046-10-0 Not Determined Not Determined
N,N-Dialkyamino-diphenylmethane 5285-60-9 Not Determined Not Determined
Propylene Carbonate 108-32-7 Not Determined Not Determined
gamma-Glycidoxypropyltrimethylsiloxane 2530-83-8 Not Determined Not Determined
Pigment Dispersion N/A Not Determined 10mg/m3
Alkali-aluminosilcate N/A 10mg/m3 6.0mg/m3
Castor Oil 8001-79-4 Not Determined Not Determined
Section 3: Hazards Identification
Emergency Overview:
Routes of Entry: Route Entry Risk
Possible
Inhalation
Possible
Ingestion
Skin Contact Possible
Eye Contact Possible
Potential Health Effects: Inhalation May cause nausea and respiratory tract irritation. May cause respiratory sensitization
in susceptible individuals.
Ingestion Moderately toxic, cause abdominal cramps, nausea, swelling.
Skin Contact Product is a slight skin irritant. May Cause swelling and redness.
Eye Contact Mild eye irritant. Vapors slightly uncomfortable. Splashes irritating and painful.
Acute Health Hazards: Acute ingestion causes burning of the mouth, throat, and stomach with abdominal pain. Acute
inhalation of vapors and mist can cause nasal discharge and pain in the eyes.
Chronic Health Hazards: If misted or at high concentrations, may cause pallor, nausea, anesthetic or narcotic effects.
Medical Conditions Skin and eye sensitization. Depending on individual skin sensitivity, chronic or prolonged exposure
Generally Aggravated by
may result in irritation, blistering, burning and peeling of skin layers.
Exposure:
Carcinogenicity: No data No data No data No data
OSHA: ACGIH: NTP: IARC:
Other:
Section 4: First Aid Measures
Eye Contact: Immediately flush with plenty of water for at least 15 minutes. If redness, itching, or a burning
sensation develops, seek medical attention.
Skin Contact: Remove from skin immediately. Rinse with clean water for 20-30 minutes. Use soapy water if
needed. If redness, itching, or a burning sensation develops, seek medical attention.
Advantage Chemical Coatings ?010 ACC 201 MSDS
Rev: 02-08-08 Page 5 of 8
Ingestion: Do NOT induce vomiting! Dilute with water and seek medical attention immediately.
Inhalation: Move victim to fresh air immediately. Give oxygen and seek medical attention.
Section 5: Fire-Fighting Measures
Flammable Limits: Class IIIB
Flash Point, (Method >200?Fahrenheit (Pensky-Marten Closed)
Used):
Autoignition Temperature:
NFPA Hazard Rating: Hazard Scale Protective Equipment
Health:
0=LEAST A=SAFETY GLASSES
Flammability:
1=SLIGHT B=SAFETY GLASSES, GLOVES
Reactivity: 2=MODERATE C=SAFETY GLASSES, GLOVES AND APRON
3=HIGH
Other: 4=EXTREME
HMIS Hazard Rating: Health:
Flammability:
Reactivity:
Protection:
Extinguishing Media: Foam/Carbon dioxide/Dry Chemical/Water Fog
Special Fire Fighting Remove all ignition sources. Wear self-contained breathing apparatus and complete personal
Procedures:
protective equipment when entering confined areas where potential for exposure to vapors or
products exist.
Unusual Fire and Closed containers may rupture due to build-up of pressure when exposed to extreme heat.
Explosion Hazards:
Hazardous Decomposition
Products:
Section 6: Accidental Release Measures
Accidental Release Standard hydrocarbon spill procedures apply to this product.
Measures:
Section 7: Handling and Storage
Handling & Storage Prevent all skin and eye contact. Avoid breathing vapors. Re-seal partially used containers. Wash
Precautions:
with soap and water before eating or drinking. Protect from moisture contamination. Exothermic
generation of carbon dioxide may cause dangerous pressure. Keep away from all ignitable sources as
well as extreme heat.
Section 8: Exposure Control/Personal Protection
Ventilation: Adequate ventilation required. Local exhaust may be required in some areas. Special exhausting
generally not required. Mechanical exhaust usually adequate.
Respiratory Protection: Respiratory masks should be worn at all times when adequate ventilation does not exist. A
NIOSH/MSHA respirator is acceptable.
Eye Protection: Chemical tight goggles; full face shield if splashing is possible.
Skin Protection: Coveralls and impervious foot covering is recommended.
Other Protective Clothing Use impervious gloves, neoprene or rubber.
or Equipment:
Work/Hygenic Practices: Good air flow in working area. Eyewash station and safety shower should be available. Gloves and
respiratory equipment should be worn at all times.
Section 9: Physical and Chemical Properties
Gray or color of pigment additive
Appearance:
Slight ammonia odor
Odor:
Physical State:
ph As Supplied:
ph (Other):
Boiling Point: 395?Fahrenheit
Advantage Chemical Coatings ?010 ACC 201 MSDS
Rev: 02-08-08 Page 6 of 8
No data
Melting Point:
Freezing Point:
No data
Vapor Pressure (mmHg):
No data
Vapor Density (Air=1):
Specific Gravity (Water=1): 1.05
Evaporation Rate (Butyl
Slower than
Acetate=1):
1-10%
Solubility in Water:
Percent Solids by Weight:
Percent Volatile: By Weight: By Volume:
Volatile Organic
With Water: Without Water:
Compounds (VOC):
Molecular Weight:
Viscosity:
Section 10: Stability and Reactivity
Stability: Stable
Conditions to Avoid excessive heat, open flam, sparks and strong oxidizing agents. Protect from atmospheric
Avoid (Stability):
moisture. Replace outage with inert dry nitrogen.
Incompatibility (Materials Avoid strong oxidizers, acids.
to Avoid):
Hazardous Decomposition Carbon dioxide, carbon monoxide, nitrogen oxides
or Byproducts:
Hazardous Polymerization: Will not occur
Conditions to Avoid Avoid incompatible reactants, especially strong bases, water or temperatures over 160?Centigrade.
(Polymerization):
Section 11: Toxicological Information
Toxicological Information: No Data
Section 12: Ecological Information
Ecological Information: No Data
Section 13: Disposal Considerations
Waste Disposal Method: Dispose of according to local, state and federal regulations.
Non-Regulated
RCRA Hazard Class:
Section 14: Transport Information
U.S. Department of Transportation
Proper Shipping Name: Polyol Resin
Hazard Class: Non-Regulated, NOI
ID Number:
Packing Group:
Label Statement:
Water Transportation
Proper Shipping Name:
Hazard Class: Non-regulated, NOI
ID Number:
Packing Group:
Advantage Chemical Coatings ?010 ACC 201 MSDS
Rev: 02-08-08 Page 7 of 8
Label Statement:
Air Transportation
Proper Shipping Name:
Hazard Class: Non-regulated, NOI
ID Number:
Packing Group:
Label Statement:
Other Agencies:
Section 15: Regulatory Information
U.S. Federal Regulations
TSCA (Toxic Substance Control Act):
CERCLA (Comprehensive Response
Compensation and Liability Act):
SARA Title III (Superfund Amendments
and Reauthorization Act):
311/312 Hazard Categories:
313 Reportable Ingredients:
State Regulations:
International Regulations:
Section 16: Other Information
Other Information:
Preparation Information:
Disclaimer: This information is formulated for use by elements of the Department of Defense. The United States of America
in no manner whatsoever expressly or implied warrants, states, or intends said information to have any
application, use or viability by or to any person or persons outside the Department of Defense nor any person or
persons contracting with any instrumentality of the United States of America and disclaims all liability for such
use. Any person utilizing this instruction who is not a military or civilian employee of the United States of
America should seek competent professional advice to verify and assume responsibility for the suitability of this
information to their particular situation regardless of similarity to a corresponding Department of Defense or
other government situation.
Advantage Chemical Coatings ?010 ACC 201 MSDS
Rev: 02-08-08 Page 8 of 8
|