Vicki Peters Nail Products MSDS#: KIM121500-J2L
ACRYLIC LIQUID MONOMER
Material Safety Data Sheet Page 1 of 5
Section 1 ?Identification of the Substance/Preparation and of the Company/Undertaking
MSDS Initial Approval Date: 12/15/2000
Product Name: ACRYLIC LIQUID
MSDS Prepared by:vp BSQ
Chemical Name: N/A
Family: Monomer Manufacturer: Vicki Peters Nail Products
2500 E. Imperial Hwy. Ste. 201 #371 Brea, CA 92821
Product Use: Nail Liquid Emergency Phone Numbers: (800) 535 - 5053
Product #: 1001718-19-20 Information Contacts: ( 856 ) 663 - 4700
Section 2 - Composition/Information on Ingredients
Chemical Identity CAS EINECS# INCI Name Exposure Limits Carcinogen %
Numbers OSHA ACGIH
TWA/STEL TWA/STEL IARC/NTP/OSHA
Ethyl Methacrylate 97-63-2 202-597-5 Ethyl methacrylate N/E N/E Not Listed 70-75
Ethylene Glycol 97-90-5 202-617-2 Glycol HEMA-Methacrylate N/E N/E Not Listed 10-15
Dimethacrylate Esters
2-hydroxyethyl methacrylate 868-77-9 212-782-2 HEMA N/E N/E Not Listed 10-15
Benzophenone 119-61-9 204-337-6 Benzophenone N/E N/E Not Listed 0-1
N,N-Dimethyl-p-toluidine 99-97-8 202-805-4 Dimethyltolyamine N/E N/E Not Listed 0-1
D&C Violet #2 81-48-1 201-353-5 CI 60725 N/E N/E Not Listed 0-1
N/E - None Established N/DA - No Data Available
N/R - Not Reviewed N/A - Not Applicable
Hazard Symbols: Xi F Risk Phrases: R11, R36/37/38, R43 Safety Phrases: S9, S16, S29, S33, S36/37/39, S45
Section 3 - Hazards Identification
EMERGENCY OVERVIEW
This information is based on findings from related or similar materials.
Flammable liquid and vapor!
?br>
May cause eye irritation.
?br>
May cause skin irritation.
?br>
Avoid prolonged or repeated breathing of gases, vapors or mists.
?br>
Please read entire MSDS for additional information.
?br>
Potential Health Effects, Signs and Symptoms of Exposure:
Primary Route of Entry Inhalation , skin , eyes
Eye Vapor concentrations may cause irritation of eyes. Liquid contact with eyes can cause irritation
and possible corneal damage.
Skin Liquid concentration may cause moderate skin irritation. Repeated or prolonged contact may
cause allergic skin rashes, itching and swelling which becomes evident on re-exposure to this
product.
Ingestion Causes irritation, a burning sensation of the mouth, throat and respiratory tract and abdominal pain.
Inhalation High vapor concentrations may irritate the respiratory system. Prolonged exposure can lead to
headaches , nausea , drowsiness and unconsciousness.
Sub-Chronic Effects Unlikely to present a cancer hazard in man.
NOTE: Refer to Section 11, Toxicological Information for Details
Section 4 - First Aid Measures
First Aid for Eye Flush with water for 15 minutes, including under eyelids. Seek medical help if discomfort persists.
First Aid for Skin Wash thoroughly with soap and water. Remove contaminated clothing and wash before reuse. Seek
medical attention if discomfort persists.
First Aid for Inhalation Remove to fresh air. If having breathing difficulty, give oxygen. If breathing has stopped, give
artificial respiration. Get medical help if discomfort persists.
First Aid for Ingestion Rinse mouth out with water. Only induce vomiting if directed by a physician. Never give anything
by mouth to an unconscious person. Seek prompt medical attention.
Revised Date: 03/23/2006 | Replaces Date: 1/19/2005
Vicki Peters Nail Products MSDS#: KIM121500-J2L
ACRYLIC LIQUID MONOMER
Material Safety Data Sheet Page 2 of 5
Section 5 - Fire Fighting Measures
Flash Point Flammable Limit Auto-ignition Temperature
(癋/癈) (vol%) (vol%)
Tag Closed Cup: 68癋/20篊 LEL : 2% ; UEL : 2.5% 392.8 ?C
Method:
Extinguishing Media: Foam, Carbon Dioxide, Dry Chemical or Carbon Tetrachloride.
Fire Fighting Instructions: Wear self-contained breathing apparatus and full protective gear. Water may be ineffective
unless used as a fine spray or fog. Use water spray to cool the exposed containers of
methacrylate monomer.
Unusual Hazards: Vapors may travel to source of ignition and flash back. Avoid ignition sources or excessive
temperatures. Heat can induce polymerization with rapid release of energy. Closed containers
may rupture explosively. Spontaneous polymerization may occur with prolonged aging.
Section 6 - Accidental Release Measures
Spill or Release Eliminate all sources of heat and ignition. Use absorbent material for spills and dike it, wash spill material into retaining
containers. Place containers in a well ventilated area. Consult an expert on disposal of recovered material and
Procedures
ensure conformity to local disposal regulations. Keep unnecessary and unprotected personnel from entering. Contain
and recover liquid when possible. Use non-sparking tools and equipment. Collect liquid in an appropriate container or
absorb with an inert material (e. g., vermiculite, dry sand, earth), and place in a chemical waste container. Do not use
combustible materials, such as sawdust. Do not flush to sewer! US Regulations (CERCLA) require reporting spills and
releases to soil, water and air in excess of reportable quantities. The toll free number for the US Coast Guard National
Response Center is (800) 424-8802. EU Regulations require the consultation of Directive 98/24/EC. If a leak or spill has
not ignited, use water spray to disperse the vapors, to protect personnel attempting to stop leak, and to flush spills away
from exposures.
Section 7 - Handling and Storage
Handling Keep away from heat, sparks, flames and other sources of ignition. Avoid contact with eyes, skin and
clothing. Avoid breathing vapor or mist . Use with adequate ventilation. Ground all metal containers when
transferring and use explosion-proof equipment. Follow all MSDS/label precautions even after the
container is emptied because it may retain product residues. Wash thoroughly after handling.
Storage Store in a cool, dry area. Keep container closed when not in use. Store at ambient temperatures out
of direct sunlight. Store in a well ventilated place. Store in accordance with National Fire Protection
Association recommendations. Maintain air space inside storage containers . Inhibitor requires air (
oxygen ) contact to function. Check inhibitor levels after 3 months and return to original level.
Explosion Hazard Avoid ignition sources or excessive temperatures. Heat can induce polymerization with rapid release
of energy. Closed containers may rupture explosively. Spontaneous polymerization may occur with
prolonged aging.
Section 8 - Exposure Controls / Personal Protective Equipment
Engineering Controls Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne levels below
recommended exposure limits. Use explosion-proof ventilation equipment.
Personal Protective Equipment
General To identify additional Personal Protective Equipment (PPE) requirements, it is recommended that a hazard
assessment in accordance with the OSHA PPE Standard (29CFR1910.132) be conducted before using this
product. Provide eye wash stations and safety showers. Wear impervious clothing to prevent ANY contact
with this product, such as gloves, apron, boots, or whole body suit. Nitrile rubber is better than PVC.
Eye/ Face Protection Wear safety glasses. Wear coverall chemical splash goggles and face shield when possibility exists for eye
and face contact due to splashing or spraying material.
Skin Protection Use impermeable clothing to prevent ANY contact with this product, such as gloves, apron, boots, or
whole body suit. Neoprene and Nitrile rubber is better than PVC.
Respiratory Protection A NIOSH/MSHA approved air purifying respirator with an organic vapor cartridge or canister may be permissible
under certain limited circumstances where airborne concentrations are expected to exceed exsposure limits. Protection
provided by air purifying respirators is limited. Wear a NIOSH/MSHA or European Standard EN 149 approved full-
facepeice airline respirator in the positive pressure mode with emergency escape provisions. Follow OSHA repsirator
regulations found in 29 CFR 1910.134 or Eurpean Standard EN 149.
Revised Date: 03/23/2006 | Replaces Date: 1/19/2005
Vicki Peters Nail Products MSDS#: KIM121500-J2L
ACRYLIC LIQUID MONOMER
Material Safety Data Sheet Page 3 of 5
Section 9 - Physical and Chemical Properties
Appearance Odor & Odor Threshold PH Specific Gravity Viscosity % Volatile
Clear to Blue- sharp ester-like odor N/A (H20=1): 0.918 <1mPas @ 20篊 W/W %: 99+
violet liquid
Boiling Point/ Decomposition Octanol/Water Vapor Vapor Evaporation Solubility
Ignition
Freezing Point Temperature Partitioning Coefficient Pressure: Density Rate In Water
Log Po/w (20癈)
243篎/117篊 N/A 1. 25 mm Hg: 0.69 (Air =1) : ButylAcetate N/A 0.5g/100g
N/DA kPa @ 38篊 3.9 =1: 1.5 @20篊
Flash Point (癋/癈) Flammable Limit (vol%) Auto-ignition Temperature (vol%)
Tag Closed Cup: 68癋/20篊 LEL : 2% ; UEL : 2.5% 392.8 ?C
Section 10 - Stability and Reactivity
Stability: Incompatibility (Materials to Avoid):
Stable Reducing and oxidizing agents and UV light.
Hazardous Decomposition Products: Hazardous Polymerization:
Oxides of carbon when burned. May occur
Conditions to Avoid:
Temperatures above 60 F, oxidizing or reducing agents, peroxides and amines, storage in absence of inhibitor, and inadvertent addition of catalyst.
Section 11 - Toxicological Information
Acute Oral Toxicity Acute Dermal Toxicity Acute Inhalation Toxicity Irritation - skin Irritation - Eye
Oral (Rat) LD50 : Dermal(Rabbit) LD50 : > Inhalation (Rabbit) LD 50: 3800 ppm N/DA N/DA
13300mg/kg 9100 mg/kg
Sensitization Mutagenicity Sub-chronic Toxicity
N/DA Test positive as a mutagen on laboratory animals N/DA
Section 12 - Ecological Information
Ecotoxicological Information
Acute Toxicity to Fish Acute Toxicity to Invertebrates Acute Toxicity to Algae Bioconcentration Toxicity to Sewage Bacteria
N/DA N/DA N/DA N/DA N/DA
Chemical Fate Information
Biodegradability N/DA
Chemical Oxygen Demand N/DA
Section 13 - Disposable Considerations
Dispose of diking materials and absorbent in compliance with State, Local, and Federal regulations. Residual vapors may explode on ignition;
do not cut, drill, or weld on or near the container. Mix with compatible chemical which is less flammable and incinerate.
Whatever cannot be saved for recovery or recycling should be handled as hazardous waste and sent to a RCRA approved waste facility. Processing,
use or contamination of this product may change the waste management options. State and local disposal regulations may differ from federal
disposal regulations. Dispose of container and unused contents in accordance with federal, state and local requirements. For EU Member States,
please refer to any relevant Community provisions relating to waste. In their absence, it is useful to remind the user that national or regional
provisions may be in force.
Section 14 - Transport Information
DOT (49 CFR 172)
Proper Shipping Name: Flammable liquids, n.o.s., (ethyl methacrylate, ethylene glycol dimethacrylate esters), 3, UN1993,
PGII
Identification Number: UN1993
Marine Pollutant: No
Special Provisions: T8, T31
Emergency Response Guidebook (ERG) #: 128
IATA (DGR):
Proper Shipping Name: Flammable liquids, n.o.s., (ethyl methacrylate, ethylene glycol dimethacrylate esters), 3, UN1993,
PGII
Class or Division: 3
UN or ID Number: UN1993
Revised Date: 03/23/2006 | Replaces Date: 1/19/2005
Vicki Peters Nail Products MSDS#: KIM121500-J2L
ACRYLIC LIQUID MONOMER
Material Safety Data Sheet Page 4 of 5
Packaging Instructions:
Emergency Response Guidance (ICAO)#:
IMO (IMDG):
Proper Shipping Name: Flammable liquids, n.o.s., (ethyl methacrylate, ethylene glycol dimethacrylate esters), 3, UN1993,
PGII
Class or Division: 3.2
UN or ID Number: UN1993
Special Provisions & Stowage/Segregation: None
Emergency Schedule (EmS)#:
Other Information: Flash point = 20篊
Section 15 - Regulatory Information
US Federal Regulations
Clean Air Act: HAP/ODS This product contains the following hazardous air pollutants (HAP's) as defined by the
U. S. Clean Air Act:
?Benzophenone CAS #119-61-9 (HAP).
This product does not contain any Class1 or Class 2 ODS.
Clean Water Act: This product contains the following Hazardous Substances as defined by the CWA:
?NONE
This product does not contain any substances that are a Priority Pollutant or Toxic
Pollutant under the CWA.
FDA: Food Packaging Status This product has not been cleared by the FDA for use in food packaging and/or
other applications as an indirect food additive.
Occupational Safety and Health Act This product is considered to be a hazardous chemical under the OSHA Hazard
Communication Standard. Its hazards are:
?Immediate (acute) health hazard
?Fire hazard.
RCRA This product is considered to be a hazardous waste under RCRA (40 CFR 261) RCRA
Code:
?Ethyl methacrylate, CAS# 97-63-2, RCRA Code: U118
?Characteristic of Ignitability, RCRA Code: D001
SARA Title III: Section 302 (TPQ) This product contains no chemicals regulated under Sec. 302 as extremely hazardous
substances that carry a TPQ.
SARA Title III: Section 302 (RQ) This product contains chemicals regulated under Section 304 as extremely hazardous
chemicals for emergency release notification ("CERCLA" List).
?Ethyl Methacrylate, CAS# 97-63-2, RQ (Lbs): 1000
SARA Title III: Section 311-312: This product is considered hazardous under the OSHA Hazard Communication Standard
and is regulated under Section 311-312 (40 CFR 370). Its hazards are:
?Immediate (acute) health hazard
?Fire hazard
SARA Title III: Section 313: This product contains the following substances subject to the reporting requirements of
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986
and 40 CFR Part 372:
?NONE
TSCA Section 8(b): Inventory: This product contains chemicals listed on the TSCA inventory or otherwise complies
with TSCA premanufacture notification requirements.
State Regulations
CA Right-to-Know Law: NONE
California No Significant Risk Rule: NONE
MA Right-to-Know Law: Ethyl Methacrylate CAS #97-63-2
NJ Right-to-Know Law: Ethyl Methacrylate CAS #97-63-2
PA Right-to-Know Law: Ethyl Methacrylate CAS #97-63-2
FL Right-to-Know Law: Ethyl Methacrylate CAS #97-63-2
MN Right-to-Know Law: Benzophenone CAS #119-61-9 (HAP).
Revised Date: 03/23/2006 | Replaces Date: 1/19/2005
Vicki Peters Nail Products MSDS#: KIM121500-J2L
ACRYLIC LIQUID MONOMER
Material Safety Data Sheet Page 5 of 5
International Regulations
CDSL: Canadian Inventory Ethyl Methacrylate DSL regulatory status: Included, WHMIS: B2: flammable liquid D-2B: Toxic
(on Canadian Transitional List) N,N-dimethyl-p-toluidine DSL regulatory status: Included, WHMIS: n/da
Hydroxypropyl methacrylate DSL regulatory status: Included, WHMIS: D2B
Tetraethylene glycol dimethacrylate, n/da
EINECS: European Inventory: J-2 Acrylic Liquid:
?HAZARD SYMBOLS: Xi, F: Irritant, Highly Flammable
?RISK PHRASES: R11: highly flammable, R36/37/38: Irritating to eyes, respiratory
system and skin, R43: May cause sensitization by skin contact
?SAFETY PHRASES: S9: keep container in a well ventilated place, S16: keep away from
sources of ignition- no smoking, S29: do not empty into drains, S33: take precautionary
measures against static discharges, S36/37/39: wear suitable protective clothing, gloves
and eye/face protection, S45: In case of accident or if you feel unwell, seek medical
advise immediately (show the label where possible)
Section 16 - Other Information
Hazard Rating System (Pictograms)
NFPA: HMIS:
2
Flammability
3
3
2 1
Health Reactivity
1
Revised Sections since Last Version: 01/19/2005 Changed shipping name in Section 14
Revised Sections since Last Version: 03/23/2006 Overall format update, and update section 16.
The information presented herein was obtained from sources considered to be reliable. However, this information is provided without
any warranty, expressed or implied, regarding its correctness or suitability for consumers intended use and/or application. For this and
other reasons, we assume no responsibility and expressly disclaim liability for loss, damage or expense arising out of any way
connected with the handling, storage, use or disposal of the product. This MSDS was prepared expressly for this product. Use the
materials only as directed. If the product is used as a component of another product, the information contained within the MSDS may
not be applicable. If one could have any concerns with or problems understanding this MSDS form, please direct all questions to
INFOTRAC, Chemical Emergency Resources System at 1(800) 535-5053.
Revised Date: 03/23/2006 | Replaces Date: 1/19/2005
|