Permatex, Inc.
10 Columbus Blvd.
Hartford, CT 06106 USA
Telephone: 1-87-Permatex
(877) 376-2839
Emergency: 800-255-3924
International Emergency: +01-813-248-0585
Material Safety Data Sheet
1. PRODUCT IDENTIFICATION
Product Name: 00112 O-RING SPLICING KIT PART 1
Item No: 151030B
Product Type: Solvent Cleaner
2. COMPOSITION/INFORMATION ON INGREDIENTS
Component Weight% ACGIH; TLV-TWA OSHA PEL
N-METHYL-2-PYRROLIDONE 40-70 Not listed Not listed
872-50-4
BUTYROLACTONE 40-70 Not listed Not listed
96-48-0
3. HAZARDS IDENTIFICATION
Causes severe eye irritation. Harmful if swallowed. Ingestion may irritate digestive tract and cause nausea,
Toxicity:
vomiting and diarrhea.
Eye and skin contact, ingestion, inhalation
Primary Routes of Entry:
May cause pain, redness or swelling of the eyes and excessive blinking and tear production. Excessive
Signs and Symptoms of Exposure:
overexposure may cause giddiness, dizziness, headache, nausea and in extreme cases, unconsciousness
and respiratory depression.
Component Weight% NTP ACGIH Carcinogens IARC
BUTYROLACTONE 40-70 male rat-no evidence; Group 3 Monograph 71, 1999;
96-48-0 female rat-no Supplement 7, 1987;
evidence, male mice- Monograph 11, 1976
equivocal evidence,
female mice-no
evidence
None known.
Medical Conditions Recognized as
Being Aggravated by Exposure:
4. FIRST AID MEASURES
Do not induce vomiting. Slowly dilute with 1-2 glasses of water or milk and seek medical attention. Never
Ingestion:
give anything by mouth to an unconscious person.
Move to fresh air in case of accidental inhalation of vapours. Obtain medical attention.
Inhalation:
Wash off with soap and water. If skin irritation persists, call a physician.
Skin Contact:
In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical
Eye Contact:
attention if irritation persists.
5. FIRE FIGHTING MEASURES
199?F. TCC
Flash Point 癋(C?:
Carbon dioxide, Dry chemical, Foam
Recommended Extinguishing Media:
Use water spray to cool exposed containers. Firefighters should wear self-
Special Fire-Fighting Procedures:
contained breathing apparatus.
Oxides of carbon, Oxides of nitrogen
Hazardous Products of Combustion:
Vapors may travel from container toward sources of ignition and flashback.
Unusual Fire/Explosion Hazards:
1.3%
Lower Explosive Limit:
9.5%
Upper Explosive Limit:
1 of 3
Product Name: 00112 O-RING SPLICING KIT PART 1 Item No: 151030B
6. ACCIDENTAL RELEASE MEASURES
Eliminate all sources of ignition. Maintain good ventilation. Take up with an inert absorbent. Store in a
Spill Procedures:
closed waste container until disposal.
7. HANDLING AND STORAGE
Store below 120 degrees F.
Storage:
Avoid contact with eyes. Do not take internally. Wash thoroughly with soap and water after handling.
Handling:
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Safety glasses.
Eyes:
Neoprene or nitrile gloves recommended.
Skin:
General; local exhaust ventilation as necessary to control any air contaminants to within their exposure
Ventilation:
limits (or to the lowest feasible levels when limits have not been established) during the use of this product.
An approved organic vapor respirator should be worn when exposures are expected to exceed the
Respiratory Protection:
applicable limits.
9. PHYSICAL AND CHEMICAL PROPERTIES
Clear liquid
Appearance:
Sweet
Odor:
395癋
Boiling Point:
Does not apply
pH:
Soluble
Solubility in Water:
1.06-1.08 @ 25癈
Specific Gravity:
100%
VOC(Wt.%):
0.29 mm Hg @ 20癈
Vapor Pressure:
>1
Vapor Density (Air=1):
Very low
Evaporation Rate:
10. STABILITY AND REACTIVITY
Stable
Chemical Stability:
Will not occur
Hazardous Polymerization:
Strong oxidizers
Incompatabilities:
Heat.
Conditions to Avoid:
Oxides of carbon, Oxides of nitrogen
Hazardous Products of Combustion:
11. TOXICOLOGICAL INFORMATION
See Section 3
12. ECOLOGICAL INFORMATION
No data available
13. DISPOSAL CONSIDERATIONS
Recommended Method of Disposal: Disposal should be made in accordance with federal, state and local regulations.
NH - Not a RCRA Hazardous Waste Material
US EPA Waste Number:
14. TRANSPORTATION INFORMATION
DOT (49CFR 172)
Ground Transport (DOT)
Not Regulated
DOT Shipping Name:
None
Hazard Class:
None
UN/ID Number:
IATA
Not regulated
Proper Shipping Name:
None
Class or Division:
None
UN/ID Number:
IMDG
Not regulated
Proper Shipping:
None
Hazard Class:
None
UN Number:
2 of 3
Product Name: 00112 O-RING SPLICING KIT PART 1 Item No: 151030B
None
Marine Pollutant:
15. REGULATORY INFORMATION
SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313 Toxic Chemical.
N-METHYL-2-PYRROLINDONE
California Proposition 65: WARNING: This product contains a chemical known to the State of California to cause birth defects or
other reproductive harm
TSCA Inventory Status: All components of this product are listed (or exempt) on the EPA TSCA inventory.
16. OTHER INFORMATION
HEALTH 2, FLAMMABILITY 2 , REACTIVITY 0.
Estimated NFPA Rating:
HEALTH 2, FLAMMABILITY 2, PHYSICAL HAZARD 0
Estimated HMIS Classification:
NFPA is a registered trademark of the National Fire Protection Assn.
HMIS is a registered trademark of the National Paint and Coatings Assn.
Denise Boyd, Manager-Environmental, Health & Safety
Prepared By: Revision Date: January 12, 2010
Permatex. Inc. 10 Columbus Blvd. Hartford, CT USA 06106 3
Company: Revision
Number:
1-87-Permatex (877) 376-2839
Telephone No.:
3 of 3
Permatex, Inc.
10 Columbus Blvd.
Hartford, CT 06106 USA
Telephone: 1-87-Permatex
(877) 376-2839
Emergency: 800-255-3924
International Emergency: +01-813-248-0585
Material Safety Data Sheet
1. PRODUCT IDENTIFICATION
Product Name: 00112 O-RING SPLICING KIT WITH ADHESIVE
Item No: 150095B
Product Type: Cyanoacrylate ester
2. COMPOSITION/INFORMATION ON INGREDIENTS
Component Weight% ACGIH; TLV-TWA OSHA PEL
ETHYL CYANOACRYLATE >70 0.2 ppm Not listed
7085-85-0
POLY (METHYL METHACRYLATE) <30 Not listed Not listed
9011-14-7
1 mg/m3 2 mg/m3
1,4-DIHYDROXYBENZENE 0.1-1.0
123-31-9
3. HAZARDS IDENTIFICATION
Skin contact may cause burns. Bonds skin rapidly and strongly. Causes eye irritation. Irritates mucous
Toxicity:
membranes.
Eye and skin contact, inhalation
Primary Routes of Entry:
Vapor is irritating to eyes and mucous membranes above TLV. Prolonged and repeated overexposure to
Signs and Symptoms of Exposure:
vapors may produce symptoms of non-allergic asthma in sensitive individuals.
Component Weight% NTP ACGIH Carcinogens IARC
POLY (METHYL METHACRYLATE) <30 Group 3 Vol. 19, pg 187;
9011-14-7 1979
1,4-DIHYDROXYBENZENE 0.1-1.0 male rat-some A3 - Animal Group 3; Monograph 71,
123-31-9 evidence; female rat- Carcinogen 1999; Supplement 7, 1987;
some evidence; male Monograph 15, 1977
mice-no evidence;
female mice-some
evidence
None known.
Medical Conditions Recognized as
Being Aggravated by Exposure:
4. FIRST AID MEASURES
Ingestion is not likely. The adhesive solidifies and adheres in the mouth. If lips are accidentally stuck
Ingestion:
together, apply lots of warm water to the lips and encourage maximum wetting and pressure from saliva
inside the mouth. Peel or roll lips apart. Do not try to pull the lips with direct opposing action. Saliva will lift
the adhesive in one half to two days.
Move to fresh air in case of accidental inhalation of vapours. Oxygen or artificial respiration if needed.
Inhalation:
Obtain medical attention.
Remove excess adhesive. Soak in warm, soapy water. The adhesive will come loose from the skin in
Skin Contact:
several hours. Cured adhesive does not present a health hazard even when bonded to the skin. For skin
adhesion, first immerse the bonded surfaces in warm, soapy water. Peel or roll the surfaces apart with the
aid of a blunt edge, e.g., spatula or teaspoon handle; then remove adhesive from the skin with soap and
water. Do not try to pull surfaces apart with a direct opposing action. Cyanoacrylates give off heat on
solidification. In rare cases, a large drop will increase in temperature enough to cause a burn. Burns
should be treated normally after the lump of cyanoacrylate is released from the tissue as described above.
In the event that eyelids are stuck together or bonded to the eyeball, wash thoroughly with warm water and
Eye Contact:
apply a gauze patch. The eye will open without further action, typically in 1-4 days. There will be no
residual damage. Do not try to open the eyes by manipulation. If cyanoacrylate is introduced into the eyes,
it will attach to the eye protein and will disassociate from it over intermittent periods, generally several
hours. This will cause periods of weeping until clearance is achieved. During this period, double vision may
be experienced together with a lachrymatory effect, and it is important to understand the cause and realize
that disassociation will normally occur within a matter of hours, even with gross contamination.
1 of 3
Product Name: 00112 O-RING SPLICING KIT WITH Item No: 150095B
ADHESIVE
5. FIRE FIGHTING MEASURES
185癋 TCC
Flash Point 癋(C?:
Carbon Dioxide, Dry Chemicals, Foam.
Recommended Extinguishing Media:
Firefighters should wear self-contained breathing apparatus.
Special Fire-Fighting Procedures:
Oxides of carbon
Hazardous Products of Combustion:
May polymerize exothermically.
Unusual Fire/Explosion Hazards:
Not determined.
Lower Explosive Limit:
Not determined.
Upper Explosive Limit:
6. ACCIDENTAL RELEASE MEASURES
Flood with water to polymerize. Maintain good ventilation. Take up with an inert absorbent. Store in a
Spill Procedures:
closed waste container until disposal.
7. HANDLING AND STORAGE
Store below 77癋 (25癈).
Storage:
Avoid contact with skin and eyes. Avoid contact with clothing. Do not inhale vapors. Keep container closed
Handling:
when not in use. Wash hands before eating and smoking.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Safety glasses.
Eyes:
Neoprene or nitrile gloves recommended. Do not wear protective clothes containing cotton.
Skin:
General; local exhaust ventilation as necessary to control any air contaminants to within their exposure
Ventilation:
limits (or to the lowest feasible levels when limits have not been established) during the use of this product.
An approved organic vapor respirator should be worn when exposures are expected to exceed the
Respiratory Protection:
applicable limits.
9. PHYSICAL AND CHEMICAL PROPERTIES
Clear liquid
Appearance:
Irritating
Odor:
>300癋
Boiling Point:
Does not apply
pH:
Insoluble, material hardens
Solubility in Water:
1.05
Specific Gravity:
<20 g/l (California SCAQMD Method 316B)
VOC(Wt.%):
1 mm Hg @ 20癈
Vapor Pressure:
Approximately 3
Vapor Density (Air=1):
Nil
Evaporation Rate:
10. STABILITY AND REACTIVITY
Stable at normal conditions
Chemical Stability:
Hazardous polymerization may occur if over-catalyzed or insufficiently
Hazardous Polymerization:
aerated after catalyzation. This polymerization is exothermic.
Polymerized by contact with water, alcohols, amines or alkalies.
Incompatabilities:
Avoid contact with clothes, fabrics, rags or tissue. Contact with these
Conditions to Avoid:
material may cause polymerization..
Oxides of carbon
Hazardous Products of Combustion:
11. TOXICOLOGICAL INFORMATION
See Section 3
12. ECOLOGICAL INFORMATION
No data available
13. DISPOSAL CONSIDERATIONS
Recommended Method of Disposal: Disposal should be made in accordance with federal, state and local regulations..
NH - Not a RCRA Hazardous Waste Material
US EPA Waste Number:
2 of 3
Product Name: 00112 O-RING SPLICING KIT WITH Item No: 150095B
ADHESIVE
14. TRANSPORTATION INFORMATION
DOT (49CFR 172)
Ground Transport (DOT)
Not Regulated
DOT Shipping Name:
None
Hazard Class:
None
UN/ID Number:
IATA
Not regulated
Proper Shipping Name:
None
Class or Division:
None
UN/ID Number:
IMDG
Not regulated
Proper Shipping:
None
Hazard Class:
None
UN Number:
None
Marine Pollutant:
15. REGULATORY INFORMATION
SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313 Toxic Chemical.
NONE
California Proposition 65: No California Prop 65 chemicals are known to be present.
TSCA Inventory Status: All components of this product are listed (or exempt) on the EPA TSCA inventory.
16. OTHER INFORMATION
HEALTH 2, FLAMMABILITY 2 , REACTIVITY 1.
Estimated NFPA Rating:
HEALTH 2, FLAMMABILITY 2, PHYSICAL HAZARD 0
Estimated HMIS Classification:
NFPA is a registered trademark of the National Fire Protection Assn.
HMIS is a registered trademark of the National Paint and Coatings Assn.
Denise Boyd, Manager-Environmental, Health & Safety
Prepared By: Revision Date: June 01, 2009
Permatex. Inc. 10 Columbus Blvd. Hartford, CT USA 06106 2
Company: Revision
Number:
1-87-Permatex (877) 376-2839
Telephone No.:
3 of 3
Permatex, Inc.
10 Columbus Blvd.
Hartford, CT 06106 USA
Telephone: 1-87-Permatex
(877) 376-2839
Emergency: 800-255-3924
International Emergency: +01-813-248-0585
Material Safety Data Sheet
1. PRODUCT IDENTIFICATION
Product Name: 00112 O-RING SPLICING KIT
Item No: 741260B
Product Type: Surface treating solution
2. COMPOSITION/INFORMATION ON INGREDIENTS
Component Weight% ACGIH; TLV-TWA OSHA PEL
TOLUENE 30-50 20 ppm 200 ppm
108-88-3
200 ppm; 590 mg/m3
METHYL ETHYL KETONE 35-45 200 ppm
(BUTANONE)
78-93-3
3.5 mg/m3 3.5 mg/m3
CARBON BLACK <5
1333-86-4
PHENOLIC RESIN <5 Not listed Not listed
25085-50-1
3. HAZARDS IDENTIFICATION
May cause eye and skin irritation. May cause nose, throat and respiratory irritation. The solvent(s) listed
Toxicity:
have been reported to affect the central nervous system. Long term exposure to high concentrations of
vapor may cause lung, liver or kidney damage.
Eye and skin contact, ingestion, inhalation
Primary Routes of Entry:
Excessive accidental exposure may cause headache, dizziness, nausea and mild respiratory irritation.
Signs and Symptoms of Exposure:
Moderately toxic if swallowed. Irritating to mouth, throat and stomach with nausea. Overexposure may
cause eye and skin redness.
Component Weight% NTP ACGIH Carcinogens IARC
TOLUENE 30-50 male rat-no evidence; A4 - Not Classifiable Group 3; Monograph 71,
108-88-3 female rat-no as a Human 1999; Monograph 47, 1989
evidence; male mice- Carcinogen
no, female mice-no
CARBON BLACK <5 Group A4 - Not Group 2B; Monograph 65,
1333-86-4 classifiable as a 1996
human carcinogen
Toluene: Eye, liver, skin, respiratory and central nervous system disorders, alcoholism. Carbon black:
Medical Conditions Recognized as
respiratory disorders.
Being Aggravated by Exposure:
4. FIRST AID MEASURES
Do not induce vomiting. Slowly dilute with 1-2 glasses of water or milk and seek medical attention. Never
Ingestion:
give anything by mouth to an unconscious person.
Move to fresh air in case of accidental inhalation of vapours. Obtain medical attention.
Inhalation:
Wash off with soap and water. If skin irritation persists, call a physician.
Skin Contact:
In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical
Eye Contact:
attention if irritation persists.
5. FIRE FIGHTING MEASURES
30癋 TCC
Flash Point 癋(C?:
Carbon Dioxide, Dry Chemicals, Foam.
Recommended Extinguishing Media:
Firefighters should wear self-contained breathing apparatus.
Special Fire-Fighting Procedures:
Irritating vapors, Oxides of carbon
Hazardous Products of Combustion:
Closed containers may rupture or explode when exposed to extreme heat.
Unusual Fire/Explosion Hazards:
Vapors may travel from container toward sources of ignition and flashback.
1 of 3
Product Name: 00112 O-RING SPLICING KIT Item No: 741260B
5. FIRE FIGHTING MEASURES
2.0%
Lower Explosive Limit:
9.0%
Upper Explosive Limit:
6. ACCIDENTAL RELEASE MEASURES
Eliminate all sources of ignition. Maintain good ventilation. Take up with an inert absorbent. Store in a
Spill Procedures:
closed waste container until disposal.
7. HANDLING AND STORAGE
Store below 100癋.
Storage:
Avoid prolonged skin contact. Keep away from eyes. Avoid breathing vapors, if exposed to high vapor
Handling:
concentration, leave area at once. Do not take internally.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Safety glasses.
Eyes:
Neoprene or nitrile gloves recommended.
Skin:
General; local exhaust ventilation as necessary to control any air contaminants to within their exposure
Ventilation:
limits (or to the lowest feasible levels when limits have not been established) during the use of this product.
An approved organic vapor respirator should be worn when exposures are expected to exceed the
Respiratory Protection:
applicable limits.
9. PHYSICAL AND CHEMICAL PROPERTIES
Black liquid
Appearance:
Solvent
Odor:
200癋
Boiling Point:
Does not apply
pH:
Nil
Solubility in Water:
0.86 @ 20癈
Specific Gravity:
81%
VOC(Wt.%):
<70 mmHg
Vapor Pressure:
2.9 (air = 1)
Vapor Density (Air=1):
4 (butyl acetate = 1)
Evaporation Rate:
10. STABILITY AND REACTIVITY
Stable
Chemical Stability:
Will not occur
Hazardous Polymerization:
Strong oxidizers
Incompatabilities:
Keep away from heat, sparks and open flame. - No smoking.
Conditions to Avoid:
Irritating vapors, Oxides of carbon
Hazardous Products of Combustion:
11. TOXICOLOGICAL INFORMATION
See Section 3
12. ECOLOGICAL INFORMATION
No data available
13. DISPOSAL CONSIDERATIONS
Recommended Method of Disposal: Disposal should be made in accordance with federal, state and local regulations.
D001/D035 as per 40CFR 261.21 and a TCLP waste per 261.24 (methyl ethyl ketone and benzene)
US EPA Waste Number:
14. TRANSPORTATION INFORMATION
DOT (49CFR 172)
Ground Transport (DOT)
Consumer Commodity (not more than one liter)
DOT Shipping Name:
ORM-D
Hazard Class:
None
UN/ID Number:
IATA
Consumer Commodity (Not more than 1 liter)
Proper Shipping Name:
2 of 3
Product Name: 00112 O-RING SPLICING KIT Item No: 741260B
14. TRANSPORTATION INFORMATION
Class 9
Class or Division:
ID 8000
UN/ID Number:
IMDG
Flammable liquids, n.o.s., (Toluene, methyl ethyl ketone)
Proper Shipping:
Class 3, PG II
Hazard Class:
UN 1993
UN Number:
None
Marine Pollutant:
15. REGULATORY INFORMATION
SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313 Toxic Chemical.
TOLUENE
California Proposition 65: WARNING: This product contains a chemical known to the State of California to cause birth defects or
other reproductive harm
TSCA Inventory Status: All components of this product are listed (or exempt) on the EPA TSCA inventory.
16. OTHER INFORMATION
HEALTH 3, FLAMMABILITY 3 , REACTIVITY 0.
Estimated NFPA Rating:
HEALTH 3, FLAMMABILITY 3, PHYSICAL HAZARD 0
Estimated HMIS Classification:
NFPA is a registered trademark of the National Fire Protection Assn.
HMIS is a registered trademark of the National Paint and Coatings Assn.
Denise Boyd, Manager-Environmental, Health & Safety
Prepared By: Revision Date: January 12, 2010
Permatex. Inc. 10 Columbus Blvd. Hartford, CT USA 06106 4
Company: Revision
Number:
1-87-Permatex (877) 376-2839
Telephone No.:
3 of 3
|