degussa
creating essentials
Material Safety Data Sheet
KRESTO?KREME MSDS ID: SK-140C-AS
* * * Section 1 - Chemical Product and Company Identi cation * * *
Product Name: KRESTO?KREME
Product Use: Hand Cleanser
Manufacturer Information: Phone: NON EMERGENCY
Stockhausen, Inc. Pryme Australia: + 61 7 3374 4544
2401 Doyle Street Pryme New Zealand: + 64 9 580 0157
Greensboro, NC 27406
Australian/New Zealand Supplier Information:
Address: Unit 10/38 Limestone Street, Darra QLD 4076 Phone: EMERGENCY
Phone: +61 7 3374 4544 Australia : 000
Fax: +61 7 3374 4768 New Zealand: 111
Email: custserv@pryme.net.au
General Comments
Emergency telephone numbers are to be used only in the event of chemical emergencies involving a spill, leak,
re, exposure or accident involving the product. All Non-emergency questions should be directed to the
Australian, Non-Emergency number above.
* * * Section 2 ?Hazards Identi cation * * *
Emergency Overview
No particular hazards known.
Potential Health E ects: Eyes
This product may cause slight irritation to the eyes.
Potential Health E ects: Skin
None.
Potential Health E ects: Ingestion
If swallowed seek medical attention.
Potential Health E ects: Inhalation
None.
HMIS Ratings: Health: 1 Fire: 0 Reactivity: 0 Pers. Prot.: None required.
Hazard Scale: 0 = Minimal 1 = Slight 2 = Moderate 3 = Serious 4 = Severe * = Chronic hazard
* * * Section 3 ?Composition / Information on ingredients * * *
Component Information/Information on Non-Hazardous Components
The manufacturer lists no ingredients as hazardous according to 29CFR1910.1200
This product is a cosmetic intended for personal use in the workplace and is thus regulated by the FDA.
See container label regarding proper handling and use of this product.
Ingredients are listed in descending order of concentration on the container label.
For OSHA workplace hazards, investigate and read and understand component MSDS's before manufacturing.
Toxic Substances Control Act (TSCA): Exempt
Workplace Hazardous Materials Information System(WHIMS-Canada): Exempt-cosmetic hand cleaner.
____________________________________________________________
P a ge 1 of 5 I s s ue D a te : F E B 9 , 2 0 0 7 R e v: 1 . 0 0 0 0 P rint D a te : 9 F e brua ry 2 0 0 7
Material Safety Data Sheet
KRESTO?KREME MSDS ID: SK-140C-AS
* * * Section 4 - First Aid Measures * * *
First Aid: Eyes
In case of contact, immediately flush eyes with large amounts of water, continuing to flush for 15 minutes. If
irritation persists get medical attention.
First Aid: Skin
Intended as a cosmetic hand cleaner.
First Aid: Ingestion
If material is swallowed, get medical attention or advice.
First Aid: Inhalation
If material is inhaled, immediately remove the affected person to fresh air.
* * * Section 5 - Fire Fighting Measures * * *
General Fire Hazards
None.
Upper Flammable Limit (UFL): Not determined
Lower Flammable Limit (LFL): Not determined
Method Used: DIN 51758
Flash Point: >100癈
Flammability Classification: Not applicable
Auto Ignition: Not determined
Hazardous Combustion Products
None identified.
Extinguishing Media
Dry chemical, alcohol-resistant foam, or water spray/fog.
Fire Fighting Equipment/Instructions
Fire fighters should wear self contained air supplied breathing apparatus in enclosed areas or in areas of heavy
smoke or flames.
NFPA Ratings: Health: 1 Fire: 0 Reactivity: 0
Hazard Scale: 0 = Minimal 1 = Slight 2 = Moderate 3 = Serious 4 = Severe
* * * Section 6 - Accidental Release Measures * * *
Containment Procedures
Absorb spill with inert material.
Clean-Up Procedures
Absorb spill with inert material. Shovel material into appropriate container for disposal. Flush small residuals to
the drain for normal biological wastewater treatment.
Evacuation Procedures
None.
Special Procedures
None.
* * * Section 7 - Handling and Storage * * *
Handling Procedures
No special requirements.
Storage Procedures
No special requirements.
____________________________________________________________
Page 2 of 5 Issue Date: FEB 9, 2007 Rev: 1.0000 Print Date: 9 February 2007
Material Safety Data Sheet
KRESTO?KREME MSDS ID: SK-140C-AS
* * * Section 8 - Exposure Controls / Personal Protection * * *
Exposure Guidelines
A: General Product Information
FDA regulated.
For OSHA workplace hazards, investigate and read and understand component MSDS's before manufacturing.
B: Component Exposure Limits
The following component information is mainly for manufacturing, since the individual components are handled by
the manufacturer employees, and the need for exposure limit communication is critical for those handlers of
components.
Component Exposure Limits
Dichloroacetic acid (79-43-6) (in the Betain @ < 0.01%)
ACGIH: 0.5 ppm TWA
Silica, cristobalite (14464-46-1) (in the organo clay @ <0.005%)
ACGIH: 0.025 mg/m3 TWA (respirable fraction)
Quartz (14808-60-7) ( in the organo clay @ < 0.01%)
ACGIH: 0.025 mg/m3 TWA (respirable fraction)
Engineering Controls
None necessary.
PERSONAL PROTECTIVE EQUIPMENT
Personal Protective Equipment: Eyes/Face
Avoid eye contact.
Personal Protective Equipment: Skin
None.
Personal Protective Equipment: Respiratory
Not required for product end use.
Personal Protective Equipment: General
Obey reasonable safety precautions and practice good housekeeping.
* * * Section 9 - Physical & Chemical Properties * * *
White emulsion Perfume fragrance
Appearance: Odor:
Emulsion ~5.3@100g/l (20癈)
Physical State: pH:
Not Established Not established
Vapor Pressure: Vapor Density:
~100癈 Not established
Boiling Point: Melting Point:
1.04 gm/cm3 (20癈)
Water soluble @20癈
Solubility (H2O): Specific Gravity:
>100癈 (DIN51758)
Flash Point:
* * * Section 10 - Chemical Stability & Reactivity Information * * *
Chemical Stability
Stable under usual application conditions.
Chemical Stability: Conditions to Avoid
None.
Incompatibility
None identified.
Hazardous Decomposition
____________________________________________________________
Page 3 of 5 Issue Date: FEB 9, 2007 Rev: 1.0000 Print Date: 9 February 2007
Material Safety Data Sheet
KRESTO?KREME MSDS ID: SK-140C-AS
None identified.
Hazardous Polymerization
Hazardous polymerization will not occur.
* * * Section 11 - Toxicological Information * * *
Acute and Chronic Toxicity
A: General Product Information
None.
B: Product Toxicity
No information is available
Carcinogenicity
A: General Product Information
Not listed by ACGIH, IARC, NIOSH, NTP OR OSHA.
Other Toxicological Information
No information is available.
* * * Section 12 - Ecological Information * * *
Ecotoxicity
A: General Product Information
Readily degradable. Prevent concentrated product from entering surface waters without biological waste water
treatment.
B: Component Analysis - Ecotoxicity - Aquatic Toxicity
Pertoleum distillates hydrotreated middle (64742-46-7)
96 Hr LC50 Pimephales promelas: 35 mg/L [flow-through]
Environmental Fate
No information available.
* * * Section 13 - Disposal Considerations * * *
A: General Product Information
Controlled release of diluted product into a biological wastewater treatment plant.
B: Component Waste Numbers
None
Disposal Instructions
Dispose of waste material according to Local, State, Federal, and Provincial Environmental Regulations.
* * * Section 14 - Transportation Information * * *
International Transportation Regulations
This product is not regulated as a hazardous material by the United States (DOT) or Canadian (TDG)
transportation regulations.
____________________________________________________________
Page 4 of 5 Issue Date: FEB 9, 2007 Rev: 1.0000 Print Date: 9 February 2007
Material Safety Data Sheet
KRESTO?KREME MSDS ID: SK-140C-AS
* * * Section 15 - Other Information * * *
Other Information
The information provided in this Material Safety Data Sheet is correct to the best of our knowledge, information
and belief at the date of its publication. The information given is designed only as guidance for safe handling,
use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality
specification. The information relates only to the specific material designated and may not be valid for such
material used in combination with any other materials or in any process unless specified in the text.
MSDS History
This is a revised MSDS for Australia from the US manufacturer.
Contact: Customer Service Manager
Contact Phone: (07) 3374 4544
This is the end of MSDS ID: SK-140C-AS
____________________________________________________________
Page 5 of 5 Issue Date: FEB 9, 2007 Rev: 1.0000 Print Date: 9 February 2007
|