MATERIAL                   SAFETY               DATA             SHEET



 PRODUCT NAME: Pre-Coat Self-Etch Primer

 PRODUCT CODE: PCSEP1                                                                            Page 1

                                                                                 HMIS CODES: H F R P

                                                                                             230I



                         SECTION I : MANUFACTURER'S IDENTIFICATION



MANUFACTURER'S NAME:                                                          ADDRESS:

                                                                              630 N. 13th Street

Kline's Auto, Inc.

                                                                              Allentown, PA 18102

EMERGENCY PHONE (Chemtrec): (800) 424 - 9300                                  DATE PRINTED: 2/19/03

INFORMATION PHONE         : (610) 434 - 7470

FAX NUMBER                : (610) 433 ?5417



             SECTION II : HAZARDOUS INGREDIENTS/SARA III INFORMATION

                                                    VAPOR PRESSURE WEIGHT

REPORTABLE COMPONENTS                        CAS#        mm Hg@TEMP PERCENT

* Ethanol                                                         64-17-5        44       20 C     40 - 45

       ACGIH TWA 1000ppm, OSHA TWA 1000ppm

Isobutyl Alcohol                                                  78-83-1        8.8      20 C     10 - 15

       ACGIH (TLV) 50 ppm TWA

       OSHA (USA) PEL 50 ppm TWA

* Toluene                                                         108-88-3       38       20 C     5 - 10

       OSHA TWA 100 ppm

* Xylene                                                          1330-20-7      9.5      20 C     1-5

       OSHA TWA 100ppm, STEL 150ppm

* Mineral Spirits                                                 8052-41-3      3.4      20 C     <1



* Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR

372. WARNING: DETECTABLE AMOUNTS OF A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND/OR BIRTH

DEFECTS OR OTHER REPRODUCTIVE HARM MAY BE PRESENT IN THIS PRODUCT.





                         SECTION III: PHYSICAL/CHEMICAL CHARACTERISTICS



BOILING RANGE:                                                     SPECIFIC GRAVITY (H2O=1):

173 F - 360 F                                                      .9323

VAPOR DENSITY:                                                     EVAPORATION RATE:

Heavier than air.                                                  Faster than n-butyl acetate.

COATING V.O.C.:                                                    MATERIAL V.O.C.:

6.08 lb/gl                                                         5.91 lb/gl

SOLUBILITY IN WATER:                                               APPEARANCE AND ODOR:

Non Soluble.                                                       Gray in color, solvent odor.



                            SECTION IV : FIRE AND EXPLOSION HAZARD DATA



FLASH POINT:                                                       METHOD USED:

45 F                                                               TCC

FLAMMABLE LIMITS IN AIR BY VOLUME:                                 LOWER:       UPPER:

                                                                   0.7          19.

EXTINGUISHING MEDIA:

Foam, alcohol foam, CO2, dry chemical, water fog.

               MATERIAL             SAFETY       DATA        SHEET



PRODUCT NAME: Pre-Coat Self-Etch Primer

PRODUCT CODE: PCSEP1                                                 Page 2



SPECIAL FIREFIGHTING PROCEDURES:

Never use welding or cutting torch on or near containers (even empty)

because product (even just residue) can ignite explosively. Respiratory

equipment should be worn to avoid inhalation of concentrated vapors. Water

should not be used except as a fog to keep nearby containers cold.



UNUSUAL FIRE AND EXPLOSION HAZARDS:

Handle as flammable liquid. Vapors form explosive mixture in air between

upper and lower explosive limits which can be ignited by many sources such

as pilot lights, open flames, electrical motors and switches. Water should

be used to cool containers exposed to fire. Fire fighting personnel should

wear self-contained breathing apparatus.



                              SECTION V : REACTIVITY DATA



STABILITY:

Stable.



CONDITIONS TO AVOID:

High temperatures, flame, sparks. Poor ventilation, corrosive atmospheres.

Avoid strong acids or bases in bulk and elevated temperatures.



INCOMPATIBILITY (MATERIALS TO AVOID):

Alkaline materials, strong acids, and oxidizing agents.



HAZARDOUS DECOMPOSITION OR BYPRODUCTS:

Oxides of carbon, toxic fumes, peroxides.



HAZARDOUS POLYMERIZATION:

Will not occur.



                           SECTION VI : HEALTH HAZARD DATA



INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:

Routes of Entry: inhalation, skin contact, ingestion, eyes. Acute: Nose and

throat irritation, lung injury, allergic respiratory reaction, nausea,

cough, shortness of breath, dehydration, dizziness, weakness, headache,

anesthesia, drowsiness, fatigue, chest pain, vomiting, central nervous

system effects, and asphyxiation.



SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:

Eye Contact: acute: irritation, redness, pain, blurred vision, sensation of

seeing halos around lights and reversible damage. Eye Contact: contact

lenses must be removed, flush water for at least 15 minutes, consult a

physician immediately.

               MATERIAL             SAFETY       DATA      SHEET



PRODUCT NAME: Pre-Coat Self-Etch Primer

PRODUCT CODE: PCSEP1                                                    Page 3



SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:

Skin Contact: acute: extraction of natural oils with resulting dry skin,

irritation, allergic skin reactions, redness and dermatitis. Can be

absorbed through the skin causing drowsiness.



INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:

Acute: gastrointestinal irritation, nausea, vomiting, diarrhea, weakness,

dizziness, drowsiness, fatigue, lack of coordination, central nervous

system effects, and depression.



HEALTH HAZARDS (ACUTE AND CHRONIC):

In all cases if symptoms persist, seek medical attention. Other Health

Effects: intentional misuse by deliberately concentrating and inhaling the

contents may be harmful or fatal. Reports have associated repeated and

prolonged occupational overexposure to solvents with permanent brain and

nervous system damage.



CARCINOGENICITY: NTP CARCINOGEN:

No



IARC MONOGRAPHS:

No



OSHA REGULATED:

Yes



MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:

Pulmonary conditions, liver conditions, kidney conditions, respiratory

conditions, neurological disorders, cardiovascular diseases, pregnancy,

reproductive system disorders.



EMERGENCY AND FIRST AID PROCEDURES:

Inhalation Overexposure: move person to fresh air. If breathing stops apply

artificial respiration and seek immediate medical attention. Eye Contact:

Flush with large quantities of water for 15 minutes. Skin Contact: Wash

thoroughly with soap and water and see a doctor. Ingestion: Do not induce

vomiting, can cause chemical pneumonitis and pulmonary edema. Contact

physician immediately.



                  SECTION VII : PRECAUTIONS FOR SAFE HANDLING AND USE



STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:

Eliminate ignition sources, provide good ventilation, dike spill area and

add absorbent earth or sawdust to spilled liquid.

               MATERIAL             SAFETY      DATA         SHEET



PRODUCT NAME: Pre-Coat Self-Etch Primer

PRODUCT CODE: PCSEP1                                                 Page 4



WASTE DISPOSAL METHOD:

Collect absorbent/spilled liquid mixture into metal container cover and

seal container. Consult local, state, & federal hazardous waste regulations

before disposing into approved hazardous waste landfill. Obey relevant

laws. Dispose of in accordance with federal, state or provincial and local

pollution requirements. In addition, rags spray booth filters, paint suits,

empty cans, etc., contaminated with product may be hazardous waste.

Determine whether contaminated items are hazardous and dispose of as

appropriate. Clean preferably with a detergent, avoid the use of solvents.



PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:

Handing & Storage: Use approved bonding and grounding procedures when

transferring liquid to another container. Do not transfer to unlabeled

containers. No smoking. Store plastic containers of flammable liquids

inside closed, approved boxes or safety cabinets. Store containers out of

sun and away from heat, sparks, and open flames. Close all containers after

each use.



OTHER PRECAUTIONS:

Smoking in area where this material is used should be strictly prohibited.

Tools used with this material should be made from aluminum, brass or

copper. Plastic utensils should not be used. Note: This information is

accurate to the best of our knowledge, but is furnished without any

expressed or implied warranties. These products may be mixed with other

components before use. Before opening the packages, READ AND FOLLOW WARNING

LABELS ON ALL COMPONENTS. Intentional misuse by deliberately concentrating

and inhaling the contents can be harmful or fatal.



                           SECTION VIII : CONTROL MEASURES



RESPIRATORY PROTECTION:

When spraying this material use NIOSH approved cartridge respirator to keep

airborne mists and vapor concentrations below the time weighted threshold

limit values. When using in poorly ventilated and confined spaces, use a

fresh-air supplying respirator or self-contained breathing apparatus.

Where overspray is present, a positive pressure air supplied respirator

should be worn. If unavailable, a properly fitted organic vapor/particulate

respirator approved by NIOSH/MSHA for protection against materials in

Section 2 may be effective. Follow respirator manufacturer's directions for

use. Wear the respirator for the whole time of spraying and until all

vapors and mists are gone. NO PERSONS SHOULD BE ALLOWED IN THE AREA WHERE

THESE PRODUCTS ARE BEING USED UNLESS EQUIPPED WITH THE SAME RESPIRATOR

PROTECTION RECOMMENDED FOR THE PAINTERS. When sanding or blasting the dried

film, wear a dust/mist respirator approved by NIOSH/MSHA for dust which may

be generated from this product, underlying paint, or the abrasive.

               MATERIAL             SAFETY       DATA     SHEET



PRODUCT NAME: Pre-Coat Self-Etch Primer

PRODUCT CODE: PCSEP1                                                 Page 5



VENTILATION:

General mechanical ventilation or local exhaust should be suitable to keep

vapor concentrations below TLV. Ventilation equipment must be explosion

proof. Ventilation: Provide sufficient ventilation to keep vapor

concentration below the given TLV and/or PEL. For baking finishes, exhaust

vapors emitted during heating. Remove decomposition products formed during

welding or flame cutting of surfaces coated with this product.



PROTECTIVE GLOVES:

Protective Gloves: Required for prolonged or repeated contact. Use solvent

resistant gloves. Barrier creams are not substitutes for full physical

protection. Refer to safety equipment supplier for effective glove

recommendations.



EYE PROTECTION:

Eye Protection: Use safety goggles or face shield designed to protect

against splash of liquids when spraying or when working with open liquids

such as during mixing or pouring.



OTHER PROTECTIVE CLOTHING OR EQUIPMENT:

In cases where no monitoring for airborne contaminants has been carried

out, assume maximum exposure and use antistatic paint suit, goggles,

gloves, and air supplied respiratory equipment. All personal protective

should meet NIOSH or OSHA requirements.



WORK/HYGIENIC PRACTICES:

Eye washes and safety showers in the workplace are recommended. Hygienic

Practices: Do not eat, drink or smoke in work areas. Wash hands before

eating, smoking, or using the washroom. Launder clothing before reuse.



                                SECTION IX : DISCLAIMER



Do not handle until the manufacturer's safety precautions have been read

and understood. Regulations require that all employees be trained on

Material Safety Data Sheets for all products with which they come in

contact. While we believe that the data contained herein is accurate and

derived from qualified sources, the data are not to be taken as a warranty

or representation for which we assume legal responsibility. They are

offered solely for your consideration, investigation, and verification.

Any use of these data and information must be determined by the user to be

in accordance with applicable federal, state, provincial and local laws and

regulations.