Fiberlock Technologies, Inc.
150 Dascomb Road
Material Safety Data Sheet Andover, Ma 01810
1-800-342-3755
(Prepared According to 29 CFR 1910.1200)
SECTION I - PRODUCT IDENTIFICATION FibertackTM 6408
Fiberlock Technologies, Inc. Date of Preparation: February 17, 2006
150 Dascomb Rd. Information Telephone Number: 978-623-9987
Andover, MA 01810 Emergency Telephone Numbers:
978-623-9987 Weekdays: 978-623-9987
978-475-6205 fax After hours, weekends & holidays: CHEM-TEL
www.fiberlock.com Emergency Contact Number: (800) 255-3924
Chemical Family: Disinfectant
Chemical Formula: Proprietary Mixture
SECTION II -INGREDIENTS
COMPONANT NAME CAS NO. OSHA PEL ACGIH TLV
None*
* Note: Per 29cfr 1910.1200 (g)(2)(1)(c)(2), only hazardous substances present in excess of 1.0% by weight (or.01% for carcinogens must be listed on an MSDS
0
Melting Point Water(ICE): 32 F
SECTION III - PHYSICAL DATA
Max VOC鈥檚: 100 g/l (0.83 lbs/gal)
Boiling Point (掳F): 212
Solubility in Water: Complete
Specific Gravity (H20 =1) Wgt./gal., lbs:8.4 to 10
Evaporation Rate (Water=1):GT 1.0
Vapor Pressure (MM Hg): 17
Physical Description: Milky white liquid slight ammonia odor
Vapor Density (Air=1): <1 Water
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
Flash Point Methods Used: None
Flammable Limit: LEL: N/A UEL: N/A
DOT Proper Shipping Name: Not regulated
DOT ID#: Not regulated Marking: Keep from freezing
Extinguishing Media: Use extinguishing agent appropriate for surrounding fire.
Special Firefighting Procedures: Wear self contained positive pressurized breathing apparatus MSHA/NIOSH Approved or equivalent and
full protective gear.
0 0
Unusual Fire and Explosion Hazards: Material can splatter above 100 C/ 212 F. Dried product can burn.
SECTION V - REACTIVITY DATA
0 0
Chemical Stability: This material is considered stable. However, avoid temperatures above 177 C/ 350 F, the onset of polymer decomposition.Thermal
decomposition is dependant on time and temperature. Hazardous Polymerization: Will not occur
Decomposition Products: From thermal reaction carbon dioxide and carbon monoxide. Incompatibility (Materials to Avoid): none
SECTION VII - HEALTH HAZARDS AND FIRST AID
Carcinogenity NTP IARC Monographs OSHA Regulated
NE NE NE YES
Effects of Overexposure:
Eye Contact: Direct contact , inconsequential eye irritation.
Skin Contact: No effects of exposure expected due to contact. Product may cause slight irritation.
Inhalation: Vapors or spray may cause headache, nausea, irritation of nose, throat and lungs.
First Aid Procedures:
Eye Contact: Flush immediately with plenty of water for at least 15 minutes get medical attention if irritation persists.
Skin Contact: Rinse thoroughly with soap and water. Remove any affected clothing. Seek medical attention if irritation persists.
Inhalation: Remove to fresh air.
Ingestion: Have person drink 2 glasses of water. Get medical attention. Never give anything by mouth to an unconscious person.
SECTION VIII - SPECIAL PROTECTION INFORMATION Always maintain TLV
Respiratory Protection: None required if good ventilation is maintained. Wear respirator (MSHA/NIOSH_ approved or equivalent) suitable for
concentration and types of air contaminants encountered. Use approved Chemical/ Mechanical filters designed to remove particulates in open and
restricted ventilation areas. Use MSHA/ NIOSH- approved airline type respirators or hood in confined areas. Ventilation : Sufficient ventilation, in
pattern and volume, should be provided to keep the air contaminant concentration below applicable exposure limits. All application areas should be
ventilated in accordance with OSHA regulation 29CFR Part 1910.94 Protective Gloves: Impervious neoprene or rubber gloves. Eye Protection:
Safety glasses or chemical splash goggles. Other Protective Equipment: Disposable impervious clothing if work clothing contamination is likely. Use
protective cream if prolonged skin contact is likely. Hygienic Practices: Wash hands before eating, smoking, or using the washroom. Food and
beverages should not be consumed anywhere this product is being applied.
SECTION IX - SPILL OR LEAK PROCEDURES
For Spill: Dike or absorb with inert material and dispose of in accordance with applicable regulations.
Waste Disposal Method: The coating and any contaminated material should be thoroughly air dried and collected into drums. Dispose of in
accordance with local state, and federal regulations.
SECTION X - SPECIAL PRECAUTIONS
Label Summary: HMIS Health Hazard: 1
Flammability: 0 Personal Protection A
Physical Hazard: 1
Handling and Storage: Keep out of reach of children. For industrial or institutional use only. Keep from freezing.
|