MATERIAL SAFETY DATA SHEET
Revised/ Reviewed: July 23, 2007
POLISHING PASTE for LAPAROSCOPES
Section 1- Product and Company Information
Manufactured for: Miltex, Inc; 589 Davies Drive, York, PA 17402
Information: 717-840-9335, 717-840-9347 (fax)
Chemical Name & Synonyms: --
Chemical Formula: --
Section 2 鈥? Composition/ Information on Ingredients
No known hazardous ingredients. The material is a mixture of aluminum oxide, wool fat, and other
ingredients. As contained within the mixture, the aluminum oxide is not in respirable form.
Section 3 - Health Identification
No hazards are anticipated under normal conditions of use. The material is not known to have a skin
irritating or sensitization effect. The material is not known to have an eye irritating effect.
Primary Route(s) of Entry: Eye and Ingestion.
Carcinogen: No known carcinogenic effects.
Medical Conditions Aggravated by Exposure: None known.
Section 4 - First Aid Measures
Eyes: Flush with tepid water for at least 15 minutes. If irritation develops, seek medical attention.
Skin: Flush affected area and wash with mild soap and water.
Ingestion: Do not give anything to an unconscious or convulsing person. In case of persistent
symptoms, seek medical attention.
Inhalation: If any ill effects are noticed, remove person to fresh air. As needed, seek medical attention.
Section 5 鈥? Fire Fighting Measures
Flash Point (Test Method): 76掳C
Flammable Limits- LEL: Not established UEL: Not established
Extinguishing Media: Dry chemical, carbon dioxide, or water spray.
Special Fire Fighting Procedures: No special measures required
Unusual Fire and Explosion Hazards: None known.
Section 6 - Physical and Chemical Properties
Physical State: Solid (contains 40-percent solids)
Appearance and Odor: Color is according to specification; characteristic odor
Boiling Point (掳C): 2980 Vapor Density (Air=1): Not determined
3
Density (@20掳C): 25.58 g/cm Solubility in Water: Insoluble
Evaporation Rate (butyl acetate=1): Not determined Self-flammability: Not self-igniting.
Vapor Pressure (mm Hg): Not determined
Page 1 of 2 Laparoscope Polishing Paste MSDS
Section 7 鈥? Stability and Reactivity
Stability: Stable
Conditions to Avoid: None known.
Incompatibility/ Materials to Avoid: None known.
Hazardous Polymerization: Will not occur
Hazardous Decomposition Products: None known.
Section 8 鈥? Accidental Release, Disposal, and Ecological Information
Spill Response: Do not allow material to enter drainage system or surface or ground water. Collect
mechanically for disposal.
Waste Disposal Method: Dispose of in accordance with all applicable federal, state, and local
regulations. Small quantities can likely be disposed of with household-type waste.
Ecological, General: Slightly hazardous for water. Do not allow undiluted material to reach ground
water, water bodies, or sewage system.
Section 9 鈥? Exposure Controls/ Personal Protection
Eye Protection: Not required under normal conditions of use
Respiratory Protection: Not required under normal conditions of use
Ventilation Recommendations: General room ventilation is normally sufficient
Skin Protection: Not required under normal conditions of use.
Other: Adhere to the usual precautionary measures employed when handling chemicals
Section 10 鈥? Storage and Handling
Storage: No special requirements.
Handling: No special methods required.
Section 11 鈥? Miscellaneous
Transportation Information: Not known to be a DOT, IATA, or IMG hazardous material. Not known
to be a marine pollutant.
Other: --
Liability Disclaimer: MSDS information is provided based on OSHA鈥檚 Hazardous Communication Regulation and for use of the persons
required to receive this information under this regulation. The information is neither designed nor recommended for any other use or for
use by any other person, including compliance with other laws. Miltex does not warrant the suitability for use of this MSDS for any
other material or product not specifically identified herein. Miltex does not warrant the accuracy or authenticity of this MSDS unless it
has been obtained directly from Miltex or posted or viewed on a Miltex website. This MSDS is based on information that is believed to
be reliable, but may be subject to change as new information becomes available. Because it is not possible to anticipate all conditions of
use, additional safety precautions may be required. Since the use of this material is not under Miltex鈥檚 control, each user is responsible
for making their own determination as to the safe and proper handling of this material in their own particular use of this material. Miltex
makes no representation or warranty, either express or implied, including as to merchantability or fitness for a particular purpose.
Page 2 of 2 Laparoscope Polishing Paste MSDS
|