MATERIAL SAFETY DATA SHEET
Revised/ Reviewed: September 13, 2004
DIAMOND POLISHING PASTE
REF 404-40400 & 404-40412
A dental abrasive polishing paste used to make chair-side adjustments and to quickly polish porcelain
to a re-glaze finish.
Section 1- Product and Company Information
Manufactured for: Miltex, Inc.; 589 Davies Drive, York, PA 17402
Information: 717-840-9335, 717-840-9347 (fax)
Chemical Name & Synonyms: --
Chemical Formula: --
Section 2 鈥? Composition/ Information on Ingredients
Polyalkylene glycol monobutyl ether; CAS # 9038-95-3; 70-95%; exposure limits not established
Silicone dioxide; CAS # 112945-52-5; 5-20%; OSHA PEL = 20 mppcf, ACGIH TLV = 10 mg/m3
Section 3 - Health Identification
Emergency Overview: Prolonged or repeated contact with this product may cause redness, dryness, or
itchiness of the skin.
Potential Health Effects: Eye Contact may cause moderate to severe irritation seen as swelling and
redness of the conjunctiva. Skin Contact may cause mild irritation, redness, or dryness.
Primary Route(s) of Entry: Skin and eye contact
Carcinogen: NTP Program- Not listed IARC Program- Not listed OSHA Program- Not listed
Medical Conditions Aggravated by Exposure: May aggravate existing dermatitis.
HMIS Ratings: Health = 1; Flammability = 2; Reactivity = 0; PPE = B
Section 4 - First Aid Measures
Eyes: Flush with water for at least 15 minutes while holding eyelids open. Seek medical attention.
Skin: Wash thoroughly with soap and water.
Ingestion: No harmful effects are expected.
Inhalation: Remove to fresh air.
Section 5 鈥? Fire Fighting Measures
Flash Point: 194掳F
Auto Ignition Temperature: Not Established
Flammable Limits- LEL: N/E UEL: N/E
Extinguishing Media: All-purpose type or alcohol-type foam, carbon dioxide, or dry chemical.
Special Fire Fighting Procedures: Do not direct a solid stream of water into hot burning mass of this
material.
Unusual Fire and Explosion Hazards: Not Established
Page 1 of 2 Diamond Polishing Paste MSDS
Section 6 - Physical and Chemical Properties
Physical State: Opaque paste
Appearance and Odor: Mild, characteristic odor. Color may vary.
Melting Point (掳C): Not established (decomposes above 392掳F)
Specific Gravity (H2O=1): 0.971 Evaporation Rate (butyl acetate=1): Negligible
Vapor Pressure (mm Hg): Negligible Solubility in Water: Soluble
Vapor Density (Air=1): 9.3 pH: Not applicable
Section 7 鈥? Stability and Reactivity
Stability: Stable Conditions to Avoid: Normally unreactive
Incompatibility/ Materials to Avoid: Strong bases at high temperatures, strong acids, strong oxidizing
agents, and materials reactive with hydroxyl compounds.
Hazardous Polymerization: Will not occur
Hazardous Decomposition Products: Carbon monoxide, carbon dioxide, and vapors.
Section 8 鈥? Accidental Release, Disposal, and Ecological Information
Spill Response: Wear suitable protective clothing, especially eye protection. Wipe up small spills with
absorbent material.
Waste Disposal Method: Dispose of in accordance with all applicable federal, state, and local
regulations. Incinerate where permitted.
Ecological, General: No information available.
Section 9 鈥? Exposure Controls/ Personal Protection
Eye Protection: Splash-proof goggles
Respiratory Protection: None required at low temperatures; if mists are present, use NIOSH-approved
respirator with organic vapor cartridge.
Ventilation Recommendations: General ventilation adequate for use at low temperatures. At elevated
temperatures, or if mist is generated, use local ventilation to keep material out of workplace air.
Skin Protection: Polyvinyl chloride-coated gloves
Other: Eyewash and safety shower should be available.
Section 10 鈥? Storage and Handling
Storage: Store away from heat and flame. Keep container closed when in use.
Handling: Avoid contact with eyes, skin, and clothing. Use adequate ventilation. Wash thoroughly
after handling.
Section 11 鈥? Miscellaneous
Toxicological Information: Not known to be acutely toxic by oral, inhalation, or dermal contact.
Transportation Information: Not a DOT Hazardous Material or IATA Dangerous Good.
Other: All ingredients of this material are on the TSCA inventory.
Liability Disclaimer: MSDS information is provided based on OSHA鈥檚 Hazardous Communication Regulation and for use of the persons
required to receive this information under this regulation. The information is neither designed nor recommended for any other use or for
use by any other person, including compliance with other laws. Miltex does not warrant the suitability for use of this MSDS for any
other material or product not specifically identified herein. Miltex does not warrant the accuracy or authenticity of this MSDS unless it
has been obtained directly from Miltex, or posted or viewed on a Miltex website. This MSDS is based on information that is believed to
be reliable, but may be subject to change as new information becomes available. Because it is not possible to anticipate all conditions of
use, additional safety precautions may be required. Since the use of this material is not under Miltex鈥檚 control, each user is responsible
for making their own determination as to the safe and proper handling of this material in their own particular use of this material. Miltex
makes no representation or warranty, either express or implied, including as to merchantability or fitness for a particular purpose.
Page 2 of 2 Diamond Polishing Paste MSDS
|