Form RD250
Issue 4 19/09/02
Resene Paints Limited Telephone: (64) (4) 577 0500
32-50 Vogel Street Fax: (64) (4) 577 0600
Naenae e-mail: advice@resene.co.nz
Wellington
Emergency Phone: NZ 0800 737363
P O Box 38242
Emergency Phone: Aust. 1800 738383
Wellington Mail Centre
NEW ZEALAND
MATERIAL SAFETY DATA SHEET Version Number: 2
15/10/2004
Date Issued:
IDENTIFICATION
Product Name: ARMOURCOTE 510 HARDENER
ARMOURCOTE 510 STANDARD HARDENER
Other Names:
Description: PAINT
Uses: Hardener component of two pack protective coating
Classification of Hazardous Nature:
U N Number: 1263 Hazardous according to NZ Dangerous Goods and Toxic Substance
Dangerous Goods Class: 3.3
Regulations.
Hazchem Code: 3[Y]
Toxic Substances Schedule: Third
Packing Code: III
Physical Description/Properties
Appearance-Viscosity-Odour-pH: Viscous liquid, light tan colour. Solvent and amine odour.
Not known
Melting or Freezing Point:
Not known
Boiling Point:
Not known
Vapour Pressure (mm Hg @ 25 C):
Vapour Density (Air=1): Greater than 1
Solubility in Water (g/L @20 C): Less than 50
Percent Volatile (by weight): 10%
Specific Gravity (Water=1): 1.35
Less than 1
Evaporation Rate (Butyl Acetate=1):
Approx. Proportion WES - TWA
INGREDIENTS CAS Reg. No.
Polyamide Resin Not known Med 10-60% None Established +
Med 10-60%
Magnesium Silicate (Talc) 14807-96-6 2mg/m鲁 +
Med 10-60%
Polyamine Resin Not known None Established +
Low 0-10%
Xylene 1330-20-7 50 ppm +
Low 0-10%
Aromatic Hydrocarbon Resin 5155-81-1 None Established +
Amino Phenol 90-72-2 Low 0-10% None Established +
None Established +
Low 0-10%
Hydrocarbon Resin Not known
100ppm +
Low 0-10%
Aromatic Hydrocarbon 64742-94-54
Low 0-10%
Thixotropic Additive Not known None Established +
+ NZ OSH (WES) 2002
HEALTH HAZARD INFORMATION
Health Effects:-
Skin: Irritating to skin upon repeated or prolonged contact. Can cause sensitization or allergic reaction such as rash or
hives.
Eyes: Moderately irritating to eyes.
Inhaled: Vapour or mist is irritating to mucous membranes and respiratory system. Excessive inhalation can cause
headache, nausea, dizziness, or asphyxiation.
Swallowed: Can be harmful if swallowed.
Long Term Hazard: Overexposure to solvents can damage kidneys, liver and lungs.
First Aid:-
Skin: Wash affected area thoroughly with soap and water.
Eyes: Flush eyes immediately with plenty of water for at least 15 minutes and get medical attention.
Product Name: ARMOURCOTE 510 HARDENER Page 1 of 2
Inhaled: Provide fresh air; give oxygen or artificial respiration if breathing laboured.
Swallowed: If swallowed dilute by giving two glasses of water to drink. DO NOT induce vomiting. Consult Physician or
New Zealand National Poisons Centre (Ph 0800 764 766) Australian National Poisons Centre (Ph 1800 131
126) IMMEDIATELY. Never give anything by mouth to an unconscious person.
Advice to Doctor: Treat symptomatically.
PRECAUTIONS FOR USE
Personal Protection:-
Skin: Protective clothing. Gloves of neoprene or nitrile rubber-Industrial weight lined gauntlet recommended
Eyes: Solvent resistant safety eyewear with splash guards or side shields to prevent eye contact
Class AUS 1 half face respirator with type A organic vapour filter and class P1 particulate filter.
Breathing:
Use in well ventilated area with explosion proof equipment. Mixed product contains hazards from both
Other:
components.
Ventilation: Sufficient ventilation , in volume and pattern, should be provided to keep air contaminant concentrations
below WES - TWA limits.
SAFE HANDLING INFORMATION
Storage and Transport:-
Maximum: 40掳C. Store cool at constant temperature.
Storage
Minimum: 1掳C
Temperature:
Container Type and Material: Steel tins.
Strong oxidizers, acids, alkalis.
Incompatible Substances:
Heat, open flame, arc or sparks
Conditions to Avoid:
Will not occur.
Hazardous Polymerisation:
Usual Decomposition Products Oxides of Carbon and Nitrogen.
Spills: Keep spectators away and avoid breathing vapours or dust. Floor may be slippery: use care to avoid falling. Dike
and contain spill with inert materials (eg sand). Transfer liquid to containers for recovery or disposal and solid
diking material to separate containers for disposal. Keep spills (and as much as possible cleaning runoffs) out of
municipal sewers and open bodies of water.
Disposal: Incinerate the liquid and contaminated diking material at a permitted facility, or otherwise dispose of in
accordance with all applicable regulations.
Fire/Explosion Hazard: Flash Point: 29掳C
Auto Ignition Temperature: Not known
Upper Explosion Limit %: 7.00
Lower Explosion Limit %: 1.00
Extinguishing Media: Foam, Carbon Dioxide, Dry Chemical.
Special Fire Fighting Procedures:
Wear self contained breathing apparatus. Closed containers may explode when exposed to extreme heat. Isolate from heat,
electrical equipment, sparks and open flame.
Other Information:
Keep container closed, upright when not in use. Store in cool, dry, well ventilated area.
Contact Point: New Zealand Telephone 0800 737363 Australia Telephone 1800 738383 (24 hour)
It is Company Policy to maintain the most accurate and up to date information possible, and Resene Paints Limited aims to review these Data regularly. The information
contained herein is based on data considered accurate and reliable to the best of our knowledge as of the date issued and subsequently made available from Resene Paints
Limited. However, no warranty is expressed or implied regarding the accuracy of these Data or the results to be obtained from the use hereof. Persons using these Data are
urged by Resene Paints Limited to satisfy themselves that these Data are the latest available from Resene Paints Limited and remain current and suitable for particular
applications after intervening periods of time. Resene Paints Limited assumes no responsibility for personal injury or property damage to vendees, users, or third parties caused
by the material. Such users or vendees assume all risks associated with the use of the material.
End of MSDS
Issue Date: 15/10/2004
Product Name: ARMOURCOTE 510 HARDENER Page 2 of 2
|