Distributed By: MSDS 045
Invensys Foxboro Foxboro Rev Date: October 2004
Foxboro, MA 02035 U.S.A. Part Number D0116MR
1-866-746-6477 Page 1 of 9
MATERIAL SAFETY DATA SHEET
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
M35460 04-19-00
MSDS NUMBER : ISSUE DATE :
FLUOROLUBE¶ OIL - ALL GRADES
PRODUCT NAME :
Occidental Chemical Corporation, Occidental Tower
Manufacturer's
5005 LBJ Freeway, P.O. Box 809050
Name and
Dallas, TX 75380 (972) 404-3800
Address :
1-800-733-3665 OR 972-404-3228
24 HOUR EMERGENCY TELEPHONE :
1-800-699-4970
TO REQUEST AN MSDS :
1-800-752-5151
CUSTOMER SERVICE :
Lubricant
PRODUCT USE :
CHEMICAL NAME : Chlorotrifluoroethylene Polymer
CHEMICAL FORMULA : (C2ClF3)x
SYNONYMS/COMMON NAMES : None
______________________________________________________________________
2. COMPOSITION/INFORMATION ON INGREDIENTS
______________________________________________________________________
CAS NUMBER / NAME
9002-83-9 Ethene, chlorotrifluoro-, homopolymer
EXPOSURE LIMITS PERCENTAGE
PEL:Not Established VOL ND
TLV:Not Established WT 100
COMMON NAMES:
Listed On(List Legend Below):
00 19 22 23 50
-----------------------------------
LIST LEGEND
00 TSCA INVENTORY 19 PA REQUIREMENT- 3% OR GREATER
22 CANADIAN DOMESTIC SUB LIST 23 NJ REQUIREMENT- 1% OR GREATER
50 PHILIPPINES INVENTORY (PICCS)
MSDS 045
Part Number D0116MR
Page 2 of 9
OCCIDENTAL CHEMICAL CORPORATION PAGE 2 OF 9
MSDS NUMBER : M35460 04-19-00
PRODUCT NAME : FLUOROLUBE OIL - ALL GRADES
______________________________________________________________________
Revised
3. HAZARDS IDENTIFICATION
______________________________________________________________________
*********************** EMERGENCY OVERVIEW ***************************
* *
MAY CAUSE EYE IRRITATION.
* *
* Translucent oil *
**********************************************************************
POTENTIAL HEALTH EFFECTS
ROUTES OF ENTRY:
None known.
TARGET ORGANS:
None known.
IRRITANCY:
MAY CAUSE EYE IRRITATION.
SENSITIZING CAPABILITY:
Not expected to be a sensitizer.
REPRODUCTIVE EFFECTS:
No relevant data found.
CANCER INFORMATION:
Not classified as carcinogenic by NTP, IARC, OSHA, ACGIH, or NIOSH.
SHORT-TERM EXPOSURE (ACUTE)
INHALATION:
Due to low vapor pressure, significant exposure by inhalation appears
unlikely. However, exposure to high concentrations of mist, aerosol,
or vapors at elevated temperatures may cause irritation, coughing and
discomfort in the nose, throat, and chest.
See "Hazardous Decomposition Products" in section 10 of this MSDS for
additional information.
EYES:
May be irritating.
SKIN:
May be irritating with prolonged or repeated contact.
INGESTION:
Believed to be practically non-toxic by ingestion.
The single dose oral toxicity of this product is considered low.
MSDS 045
Part Number D0116MR
Page 3 of 9
OCCIDENTAL CHEMICAL CORPORATION PAGE 3 OF 9
MSDS NUMBER : M35460 04-19-00
PRODUCT NAME : FLUOROLUBE OIL - ALL GRADES
______________________________________________________________________
3. HAZARDS IDENTIFICATION (Continued)
______________________________________________________________________
REPEATED EXPOSURE (CHRONIC)
No adverse effects have been documented in humans as a result of
chronic exposure.
SYNERGISTIC MATERIALS:
No relevant data found.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE:
None known.
______________________________________________________________________
Revised
4. FIRST AID MEASURES
______________________________________________________________________
EYES:
IMMEDIATELY FLUSH EYES WITH A DIRECTED STREAM OF WATER for at least 15
minutes, forcibly holding eyelids apart to ensure complete irrigation
of all eye and lid tissue. Washing eyes within several seconds is
essential to achieve maximum effectiveness. GET MEDICAL ATTENTION
IMMEDIATELY.
SKIN:
Wash thoroughly with soap and water. Wash clothing before reuse. IF
IRRITATION OCCURS, GET MEDICAL ATTENTION.
INHALATION:
Remove to fresh air. IF SYMPTOMS OF OVEREXPOSURE OCCUR, GET MEDICAL
ATTENTION.
INGESTION:
No effect expected. If large amounts are ingested, GET MEDICAL
ATTENTION.
NOTES TO PHYSICIAN:
Material from high pressure equipment, pinhole leaks, or high pressure
line failure can penetrate the skin and, if not properly treated, can
cause severe injury, including disfigurement, loss of function, or
even require amputation of the affected area. To prevent such serious
injury, immediate medical attention should be sought even if the
injection injury appears to be minor.
______________________________________________________________________
Revised
5. FIRE FIGHTING MEASURES
______________________________________________________________________
Flash Point: Not applicable
Method: Not applicable
Autoignition Temperature: Not applicable
MSDS 045
Part Number D0116MR
Page 4 of 9
OCCIDENTAL CHEMICAL CORPORATION PAGE 4 OF 9
MSDS NUMBER : M35460 04-19-00
PRODUCT NAME : FLUOROLUBE OIL - ALL GRADES
______________________________________________________________________
5. FIRE FIGHTING MEASURES (Continued)
______________________________________________________________________
FLAMMABLE LIMITS IN AIR, BY % VOLUME
Upper: Not applicable
Lower: Not applicable
EXTINGUISHING MEDIA:
Use agents appropriate for surrounding fire.
FIRE FIGHTING PROCEDURES:
Keep unauthorized personnel removed and upwind. Wear NIOSH/MSHA
approved positive pressure self-contained breathing apparatus and full
protective clothing.
FIRE AND EXPLOSION HAZARD:
Fluorolubes decompose and depolymerize above 500°F. Decomposition
products may be toxic and hazardous. Avoid friction or galling in
contact with aluminum or magnesium parts. Friction or galling can
cause localized areas of instantaneously high pressure and temperature
which may result in localized detonation. See Stability and Reactivity
(Section 10) of the MSDS.
SENSITIVITY TO MECHANICAL IMPACT:
Not sensitive.
SENSITIVITY TO STATIC DISCHARGE:
Not sensitive.
______________________________________________________________________
6. ACCIDENTAL RELEASE MEASURES
______________________________________________________________________
PERSONAL PRECAUTIONS:
Follow protective measures provided under Personal Protection in
Section 8.
ENVIRONMENTAL PRECAUTIONS:
Contain spill with dike to prevent entry into sewers or waterways.
METHODS FOR CLEANING UP:
For small spills, soak up with absorbent material and place in
properly labeled containers for disposal.
Large spills should be removed by vacuum truck.
______________________________________________________________________
7. HANDLING AND STORAGE
______________________________________________________________________
HANDLING:
Do not reuse containers.
MSDS 045
Part Number D0116MR
Page 5 of 9
OCCIDENTAL CHEMICAL CORPORATION PAGE 5 OF 9
MSDS NUMBER : M35460 04-19-00
PRODUCT NAME : FLUOROLUBE OIL - ALL GRADES
______________________________________________________________________
7. HANDLING AND STORAGE (Continued)
______________________________________________________________________
Wash thoroughly with soap and water after handling.
Wear personal protective equipment as described in Exposure
Controls/Personal Protection (Section 8) of the MSDS.
SPECIAL MIXING AND HANDLING INSTRUCTIONS:
Do not allow contact with materials as noted in Section 10.
STORAGE:
Keep container tightly closed and properly labeled.
______________________________________________________________________
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
______________________________________________________________________
ENGINEERING CONTROLS:
No special ventilation required under normal use.
PERSONAL PROTECTION
RESPIRATORY:
Respiratory protection is not required under normal use.
Wear a NIOSH/MSHA approved respirator following manufacturer's
recommendations, where airborne contaminants may occur.
EYE/FACE:
Wear safety glasses with side shields or chemical safety goggles
(ANSI Z87.1).
SKIN:
Wear chemical resistant gloves such as rubber, neoprene or
vinyl.
OTHER:
None known.
______________________________________________________________________
Revised
9. PHYSICAL AND CHEMICAL PROPERTIES
______________________________________________________________________
Appearance and Odor: Translucent oil
Odor Threshold: Not determined
Specific Gravity (Water=1): 1.87-1.96 @ 38°C (100°F)
Vapor Pressure: 0.07-2.2 mm Hg @ 93°C (200°F)
Vapor Density (Air=1): Not determined
Density: 1.87-1.96 @ 38°C (100°F)
MSDS 045
Part Number D0116MR
Page 6 of 9
OCCIDENTAL CHEMICAL CORPORATION PAGE 6 OF 9
MSDS NUMBER : M35460 04-19-00
PRODUCT NAME : FLUOROLUBE OIL - ALL GRADES
______________________________________________________________________
9. PHYSICAL AND CHEMICAL PROPERTIES (Continued)
______________________________________________________________________
Evaporation Rate: Not determined
% Volatiles by Wt: Not determined
Boiling Point: Decomposes above 260°C (500°F)
Freezing Point: -90°F to 65°F (See Product Data Sheet)
Melting Point: Not determined
Solubility in Water (% by wt.): Not determined
pH: (of a water extract): 6.0 - 7.5
Octanol/Water Partition Coefficient: Not determined
Thermal Decomposition Temperature: >260°C (>500°F)
Other: Not applicable
VOC (% by wt;g/l): 100 %
______________________________________________________________________
10. STABILITY AND REACTIVITY
______________________________________________________________________
CHEMICAL STABILITY:
_____ STABLE
X _____ UNSTABLE
REACTS WITH:
_____ AIR _____ OXIDIZERS _____ METALS
_____ WATER _____ ACIDS _____ OTHER
X
_____ HEAT _____ ALKALIS _____ NONE
HAZARDOUS POLYMERIZATION:
_____ OCCURS _____ WILL NOT OCCUR
X
COMMENTS:
Do not use on aluminum or magnesium parts when heavy friction or
galling can occur. Detonation can occur when Fluorolube is allowed to
contact aluminum or magnesium, free of its oxide coating, in confined
spaces and under heavy loads or high pressure.
Reacts violently with sodium, potassium, amines, liquid fluorine,
liquid chlorine trifluoride.
HAZARDOUS DECOMPOSITION PRODUCTS:
Decomposes when heated above 500°F, releasing hazardous decomposition
products including hydrogen fluoride, hydrogen chloride,
chlorotrifluoroethylene and other toxic organic fluorine compounds.
MSDS 045
Part Number D0116MR
Page 7 of 9
OCCIDENTAL CHEMICAL CORPORATION PAGE 7 OF 9
MSDS NUMBER : M35460 04-19-00
PRODUCT NAME : FLUOROLUBE OIL - ALL GRADES
______________________________________________________________________
Revised
11. TOXICOLOGICAL INFORMATION
______________________________________________________________________
Fluorolube® Oil
A representative member of this product family was tested. This
substance is practically non-toxic by the oral and dermal routes,
slightly irritating to the skin, and has no appreciable irritation to
the eyes.
For further information call or write the telephone number on page 1
of the MSDS.
______________________________________________________________________
Revised
12. ECOLOGICAL INFORMATION
______________________________________________________________________
There are no available data on the environmental fate and potential
effects of this product. Caution should be excercised to avoid the
accidental release of this material to the environment.
______________________________________________________________________
Revised
13. DISPOSAL CONSIDERATIONS
______________________________________________________________________
Dispose of all waste and contaminated equipment in accordance with all
applicable federal, state and local health and environmental
regulations.
______________________________________________________________________
Revised
14. TRANSPORT INFORMATION
______________________________________________________________________
DOT INFORMATION: Not Regulated
______________________________________________________________________
Revised
15. REGULATORY INFORMATION
______________________________________________________________________
U.S. FEDERAL REGULATIONS:
OSHA Standard 29 CFR 1910.1200 requires that information be provided
to employees regarding the hazards of chemicals by means of a hazard
communication program including labeling, material safety data sheets,
training and access to written records. We request that you, and it
is your legal duty to, make all information in this Material Safety
Data Sheet available to your employees.
TSCA:
All components of this product that are required to be on the TSCA
inventory are listed on the inventory.
SARA/TITLE III HAZARD CATEGORIES:
If the word "YES" appears next to any category, this product may be
reportable by you under the requirements of 40 CFR 370. Please
consult those regulations for details.
MSDS 045
Part Number D0116MR
Page 8 of 9
OCCIDENTAL CHEMICAL CORPORATION PAGE 8 OF 9
MSDS NUMBER : M35460 04-19-00
PRODUCT NAME : FLUOROLUBE OIL - ALL GRADES
______________________________________________________________________
15. REGULATORY INFORMATION (Continued)
______________________________________________________________________
Immediate(Acute) Health: _____
NO Reactive Hazard _____
NO
Delayed(Chronic) Health: _____
NO Sudden Release of Pressure _____
NO
Fire Hazard: _____
NO
HMIS HAZARD RATINGS:
HEALTH HAZARD: _____
0 FIRE HAZARD: _____
0 REACTIVITY: _____
1
STATE REGULATIONS:
See Section 2. COMPOSITION/INFORMATION ON INGREDIENTS list legend for
applicable state regulation.
INTERNATIONAL REGULATIONS:
Consult the regulations of the importing country.
CANADA:
WHMIS Hazard Class: NOT CLASSIFIABLE
______________________________________________________________________
16. OTHER INFORMATION
______________________________________________________________________
For additional non-emergency health, safety or environmental
information telephone (972) 404-2076 or write to:
Occidental Chemical Corporation
Product Stewardship Department
5005 LBJ Freeway
P.O. Box 809050
Dallas, Texas 75380
MSDS LEGEND:
ACGIH = American Conference of Governmental Industrial Hygienists
CAS = Chemical Abstracts Service Registry Number
CEILING = Ceiling Limit (15 Minutes)
CEL = Corporate Exposure Limit
OSHA = Occupational Safety and Health Administration
PEL = Permissible Exposure Limit (OSHA)
STEL = Short Term Exposure Limit (15 Minutes)
TDG = Transportation of Dangerous Goods (Canada)
TLV = Threshold Limit Value (ACGIH)
TWA = Time Weighted Average (8 Hours)
WHMIS = Worker Hazardous Materials Information System (Canada)
* = See Section 3 Hazards Identification - Repeated Exposure(Chronic)
Information
MSDS 045
Part Number D0116MR
Page 9 of 9
OCCIDENTAL CHEMICAL CORPORATION PAGE 9 OF 9
MSDS NUMBER : M35460 04-19-00
PRODUCT NAME : FLUOROLUBE OIL - ALL GRADES
______________________________________________________________________
16. OTHER INFORMATION (Continued)
______________________________________________________________________
IMPORTANT: The information presented herein, while not guaranteed,
was prepared by competent technical personnel and is true and accurate
to the best of our knowledge. NO WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PURPOSE, OR OF ANY OTHER KIND, EXPRESS OR IMPLIED, IS MADE
REGARDING PERFORMANCE, STABILITY OR OTHERWISE. This information is
not intended to be all-inclusive as to the manner and conditions of
use, handling and storage. Other factors may involve other or
additional safety or performance considerations. While our technical
personnel will be happy to respond to questions regarding safe
handling and use procedures, safe handling and use remains the
responsibility of the customer. No suggestions for use are intended
as, and nothing herein shall be construed as a recommendation to
infringe any existing patents or violate any federal, state or local
laws, rules, regulations or ordinances.
This Material Safety Data Sheet (MSDS) covers the following materials:
- FLUOROLUBE® OIL - ALL GRADES
- FLUOROLUBE® FS 5
- FLUOROLUBE® MO 10
- FLUOROLUBE® S 30
- FLUOROLUBE® T 80
- FLUOROLUBE® HO 125
- FLUOROLUBE® LG 160
- FLUOROLUBE® 160
- FLUOROLUBE® FS-5 BLUE
______________________________________________________________________
Revised
17. WARNING LABEL INFORMATION
______________________________________________________________________
CAUTION
MAY CAUSE MILD EYE IRRITATION.
DO NOT USE FOR LUBRICATION OF ALUMINUM OR MAGNESIUM PARTS.
In case of eye contact, flush eyes with water for at least 15 minutes.
If irritation persists, get medical attention.
This Product Contains: CAS# NAME
9002839 Ethene, chlorotrifluoro-,
homopolymer
24 HOUR EMERGENCY PHONE 1-800-733-3665
HMIS Rating System: Health 0 Flammability 0 Reactivity 1
FOR INDUSTRIAL USE ONLY
|