MATERIAL SAFETY DATA SHEET
Liqua Pro Date Prepared:07-09-2004
SECTION 1 ?MATERIAL AND MANUFACTURER IDENTIFICATION
Product Identifier: Liqua Pro
Product Use: Extraction Emulsifier
MANUFACTURER
CTI (Chemical Technologies International Inc.)
PO BOX 968
Rancho Cordova, CA 95741
Phone: (916) 638-1315 Fax: (916) 638-0712
Emergency Assistance Calls: Chemtrec (800) 424-9300 (U.S.A.) 24hrs.
SECTION 2 ?COMPOSITION / INFORMATION ON INGREDIENTS
COMPONENT CAS #
1. Salicic Acid Disodium Salt 6834-92-0
2. EDTA Trisodium Salt 18662-53-8
3. Proprietary surfactant blend
4. Methoxypropanol 108-65-6
5. Dimethyl Carbinol 67-63-0
(SEE SECTION 8 FOR EXPOSURE GUIDELINES)
SECTION 3 ?Hazards Identification
Emergency Overview
Clear liquid with light odor.
Irritating to respiratory and digestive tract, acute nervous system, eyes and skin, harmful if swallowed.
Potential Health Effects
Routes of entry: (skin: yes) (inhalation: yes) (ingestion: yes) (eye: yes)
Inhalation:
Excessive inhalation may cause irritation of the respiratory tract.
Eye Contact:
Vapors may irritate eyes. Direct or prolonged contact with eyes will be painful and irritating may also cause possible
permanent damage.
Skin Contact:
Repeated exposure may cause skin irritation, drying, chapping.
Ingestion:
If swallowed can cause GI irritation.
Chronic effects: Not established.
SECTION 4 ?FIRST AID MEASURES
Inhalation: Remove to fresh air. If breathing is difficult , have trained person administer oxygen. If breathing stops
administer artificial respiration. Get medical attention immediately.
MSDS Product: Liquid Pro 1
Page 1 of 5, Revised Date: 07-09-2004
MATERIAL SAFETY DATA SHEET
Eye Contact: Immediately flush eyes with a directed stream of water for at least 15 minutes, forcibly holding eyelids
apart to ensure complete irrigation of all eye and lid tissue. Washing eyes within several seconds is essential to
achieve maximum effectiveness. Get medical attention immediately.
Skin Contact: Flush thoroughly with cool water while removing any contaminated clothing and shoes. Wash clothing
before reuse. Get medical attention if irritation persists after washing.
Ingestion: Get medical attention immediately.
Do not induce vomiting. Never give anything by mouth to an unconscious person. Give large quantities of water and
if available give several glasses of milk. If vomiting occurs spontaneously , keep airway clear and give more water.
SECTION 5 ?Fire Fighting Measures
Flashpoint: N/A
Flammable Limits: N/A
Autoignition Temperature: N/A
General Hazard:
During a fire smoke may contain the original material in addition to toxic and or irritating compounds. Avoid heat
sparks or open flame.
Fire Fighting Instructions:
Use dry chemical or CO2 . Use water (only to cool) nearby containers and structures exposed to fire. Direct water
stream may spread fire. Keep people away from fire, isolate fire area and deny unnecessary entry.
Fire fighting equipment:
Fire fighters should wear a self contained, positive pressure breathing apparatus and full protective clothing
(NICSH/MSHA APPROVED).
Hazardous combustion products:
Hazardous combustion products may include and are not limited to ; carbon dioxide, carbon monoxide.
SECTION 6 ?ACCIDENTAL RELEASE MEASURES
Small Spills: Wipe or mop up and dispose of in DOT approved waste container.
Large Spills: Contain by diking with soil or other non-combustible sorbant material, then dispose into DOT approved
waste container. Comply with all applicable governmental regulations on spill reporting, handling and disposal of
waste.
Contain all spills or leaks to prevent discharge into the environment. All spills or releases should be reported to the
appropriate local, state and federal agencies.
SECTION 7 ?PRECAUTIONS FOR SAFE HANDLING AND STORAGE
The manufacturer and seller warrant that this product conforms to its standard specifications when used according to
directions. As the conditions of method of its use are beyond our control, we do not assume any responsibility and
expressly disclaim any liability for use of this product. Information contained herein is believed to be true but all
statements and suggestions are made without any warranty, expressed or implied, regarding accuracy of the
information. The hazards connected with the use of this material and the results to be obtained from the use thereof.
For use by professionals ONLY.
Avoid breathing vapors of this product.
Always ensure good ventilation of surroundings during use of this chemical. Do not use this chemical in a poorly
ventilated area.
Always keep container tightly closed and properly labels.
Avoid contact with skin, eyes or clothing.
MSDS Product: Liquid Pro
Page 2 of 5, Revised Date: 07-09-2004
MATERIAL SAFETY DATA SHEET
Wash thoroughly after handling
Loosen closures cautiously.
Follow dilution recommendations
Storage temperature: store in cool dry place
Storage pressure: Atmospheric
Avoid excessive heat. Avoid storage with oxidizing or reducing agents, acids.
SECTION 8 ?EXPOSURE / PERSONAL PROTECTION
EXPOSURE LIMITS
#
COMPONENT OSHA ACGIH OTHER HAZARD
(Refer to section 2 for component #) PEL TLV LIMIT
1. 2mg/M3 2mg/M3
2. Not established
3. Not established
4. 100ppm
5. 400ppm 400ppm
Respiratory: These precautions are not usually necessary in adequately ventilated areas. Wear NIOSH/MSHA
approved respirator when ventilation is not adequate. A NIOSH /MSHA 璦pproved air purifying respirator with an
organic vapor cartridge or canister may be advisable under certain circumstances where airborne concentrations are
expected to exceed exposure limits. Protection provided by air purifying respirators is limited. Use a positive
pressure, air supplied respirator if there is any potential for uncontrolled release, exposure levels are unknown, or any
other circumstances where air-purifying respirators may not provide adequate protection.
Ventilation: Always assure adequate ventilation.
Eye Protection: Wear safety goggles to protect against contact when appropriate.
Skin: Wear protective clothing to minimize skin contact. Wash skin after use. Wash contaminated clothing and dry
before reuse.
Other:
One should always use chemicals with an awareness of the potential hazard of the effect on the human system.
To minimize employee exposure to all chemicals, including this product, use good industrial hygiene practices.
SECTION 9 ?Physical and Chemical properties
Clear liquid with light clean odor.
PH: 8.5. At ready to use 650 to 1 dilution.
PH: 13 As shipped.
Vapor pressure: not available
Vapor density: not available
Boiling point: not available >100C
Freezing/Melting point: N/A
Solubility in water: soluble
Heat Value: not available
Particle size: N/A
Evaporation rate: not available
MSDS Product: Liquid Pro
Page 3 of 5, Revised Date: 07-09-2004
MATERIAL SAFETY DATA SHEET
SECTION 10 ?Stability and Reactivity
Chemical Stability: Stable under ambient temperature and atmospheric pressure. Stable under recommended storage
and handling conditions.
Conditions to avoid: Keep away from heat or excessive pressure.
Incompatibility with other materials: Although the mixture has no known incompatibilities, some components of this
mixture are not compatible with acids, metals, oxidizing or reducing materials.
Hazardous decomposition products: There are no known hazardous decomposition materials of this mixture, some
components of this mixture may liberate sulfur dioxide, carbon monoxide, carbon dioxide, and hydrogen sulfide.
Hazardous polymerization : Major components of this mixture show no hazardous polymerization.
Section 11- Toxicological Information
Toxicological information not available on this mixture. Limits given are for components as listed in section 2.
1. LD50 rat oral 1153mg/kg
2. LD50 rat oral 630mg/kg
3. Not available
4. LD50 rat oral 5660mg/kg
5. Not available
Section 12- Ecological Information
Ecological information not established on this mixture. Ecological information on components within this mixture are
given by component number as listed in section 2.
Component # Information
1 No information reported
Section 13- Disposal practices
Dispose of all waste, empty bottles and contaminated equipment in accordance with all applicable federal, state and
local health and environmental regulations.
Do not dump into storm drains, sanitary sewers or any body of water. All disposal methods must be in compliance
with all federal, State/ Provincial and local laws and regulations. Regulations may vary in different locations.
Waste characterizations and compliance with applicable laws are the responsibility solely of the waste generator. The
vendor has no control over the management practices or the processes by which the party who handles or uses this
material. The information presented here pertains only to the product as shipped in its intended condition and
recommended usage.
Section 14- Transport information
MSDS Product: Liquid Pro
Page 4 of 5, Revised Date: 07-09-2004
MATERIAL SAFETY DATA SHEET
This mixture has no established reportable concentrations of hazardous or flammable materials regulated by DOT.
Section 15- Regulatory Information
US Federal Regulations:
OSHA standards require that information be provided to employees regarding the hazards of chemicals by means of a
hazard communication program including labeling, MSDS sheets, training and access to written records. We request
that you, and it is your legal duty to, make all information in this material safety data sheet (MSDS) available to your
employees and those who handle or consume the product.
To aid our customers in complying with regulatory requirements regulatory information for components of this
product are indicated below.
This mixture has no established regulatory information all regulatory information given is based on individual
components of the mixture by component number.
Section 16- Other Information
All information appearing herein is based upon data obtained from the manufacturer and /or recognized technical
sources of each individual component. While the information is believed to be accurate, CTI makes no representations
as to its accuracy or sufficiency. Conditions of use are beyond CTI's control and therefore users are responsible to
verify this data under their own operating conditions to determine whether this product is suitable for their particular
purposes and they assume all risks of their use, handling, and disposal of the product, or from the publication or use of,
or reliance on information contained herein. This information relates only to the product designated herein, and does
not relate to its use in combination with any other material or in any other process.
Legend:
References:
MSDS Product: Liquid Pro
Page 5 of 5, Revised Date: 07-09-2004
|