Page 1 of 3 White Glazing Putty
MATERIAL SAFETY DATA SHEET
U. S. CHEMICAL & PLASTICS
600 NOVA DRIVE SE
MASSILLON, OH 44646
Telephone: 330-830-6000
Fax: 330-830-6005
===============================================================================
SECTION I - IDENTIFICATION OF PRODUCT
===============================================================================
PRODUCT NAME: White Glazing Putty (Military Model)
PRODUCT CODE: (31170), 31171
SYNONYM OR CROSS REFERENCE: Filler Paste
SCHEDULE B NUMBER: 3214.10.0090
===============================================================================
SECTION II - HAZARDOUS INGREDIENTS
===============================================================================
INGREDIENTS WEIGHT % CAS NUMBER TLV/PEL
ACGIH: TLV 10 mg/m3
Calcium Carbonate 15-20% 1317-65-3
471-34-1
ACGIH: TLV 2 mg/m3
Talc non-asbestiform 40-45% 14807-96-6
Toluene 12-14% 108-88-3 ACGIH: TLV 100 ppm
STEL 100 ppm
OSHA: PEL-TWA 200 ppm
Butyl Acetate 1-3% 123-86-4 ACGIH: TLV 100 ppm
STEL 100 ppm
OSHA: TWA 150 ppm
Isopropanol 1-3% 63-67-0 ACGIH: TLV 400 ppm
OSHA: PEL 500 ppm
Xylene 2-4% 1330-20-7 ACGIH: TLV 100 ppm
STEL 150 ppm
OSHA: PEL-TWA 100
ACGIH: TLV 10 mg/m3
Titanium Dioxide 1-2 % 13463-67-7
Methyl Ethyl Ketone < 1% 78-93-3 ACGIH TLV 200 ppm
ACGIH TLV 5mg/m3
Dioctylphthalate 3-5% 117-81-7
Isobutyl Acetate 3-5% 110-19-0 ACGIH TLV 150 ppm
==========================================================================================
SECTION III - PHYSICAL DATA
==========================================================================================
APPEARANCE: White Paste VAPOR DENSITY: Heavier than air
SPECIFIC GRAVITY: 1.57 EVAPORATION RATE: (Ethyl Ether = 1)
VAPOR PRESSURE (mmHg): N/E Slower than Ethyl Ether
BOILING POINT: N/E VOLATILES BY WEIGHT: Approximately 26%
MELTING POINT: N/E SOLUBILITY IN WATER: Limited
VOC: 407 Grams/Liter 3.4 lbs/gal
==========================================================================================
SECTION IV - FIRE AND EXPLOSION DATA
==========================================================================================
FLASH POINT: 25oF/-4oC Seta Flash Closed Cup
LOWER FLAMMABLE LIMIT %: N/E
UPPER FLAMMABLE LIMIT %: N/E
FIRE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam.
SPECIAL FIRE FIGHTING PROCEDURES: Fight like a fuel oil fire. Cool fire exposed containers with water spray. Fire
Fighter should wear OSHA/NIOSH approved self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARD: Closed containers exposed to high temperatures, such as fire conditions may
rupture.
PDF created with pdfFactory trial version www.softwarelabs.com
Page 2 of 3 White Glazing Putty
==========================================================================================
SECTION V - HEALTH HAZARD/TOXICOLOGICAL PROPERTIES
==========================================================================================
OVEREXPOSURE EFFECTS:
ACUTE EFFECTS:
EYES - Contact with eyes can cause irritation, redness, tearing, blurred vision, and/or swelling.
SKIN - Contact with skin can cause irritation, (minor itching, burning and/or redness), Dermatitis, defatting may be
readily absorbed through the skin.
INHALATION - Inhalation of vapors can cause nasal and respiratory irritation, dizziness, weakness, fatigue,
nausea, headache, possible unconsciousness and/or asphyxiation. Aspiration of material into lungs may result in
chemical pneumonitis which can be fatal. May be toxic.
INGESTION - Ingestion can cause gastrointestinal irritation, nausea, vomiting, diarrhea.
CHRONIC EFFECTS:
Overexposure to this material has apparently been known to cause the following effects in lab animals: Central
Nervous System, skin, respiratory system, blood, kidney, and liver damage.
CARCINOGENIC YES X NO TOLUENE STATEMENT: Prolonged breathing of 2,000
TERATOGEN YES X NO ppm Toluene by pregnant rats was toxic to their fetuses
MUTAGEN YES X NO (reduced body weight, delayed ossification, skeletal
variations), but was not teratogenic. (API Study, 1986).
PRIMARY ROUTES OF EXPOSURE: skin, inhalation
FIRST AID:
INHALATION -If inhaled, remove victim from exposure to well ventilated area. Make him/her comfortably warm, but not
hot. Use oxygen or artificial respiration as required. Consult a physician.
SKIN - For skin contact, wash promptly with soap and excess water.
EYES - For eye contact, flush promptly with excess water for at least fifteen minutes. Consult a physician.
INGESTION - If ingested, do not induce vomiting. Give victim a glass of water. Call a physician immediately.
==========================================================================================
SECTION VI - REACTIVITY DATA
==========================================================================================
STABILITY: Stable
CONDITIONS TO AVOID: Open flames, sparks, heat, electrical and static discharge.
INCOMPATIBILITY MATERIALS TO AVOID: Peroxides or strong oxidizing agents
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Dioxide, Carbon Monoxide and acrid fumes
HAZARDOUS POLYMERIZATION: Will not occur.
==========================================================================================
SECTION VII - SPILL AND DISPOSAL PROCEDURE
==========================================================================================
SPILLS, LEAK OR RELEASE: Ventilate area. Remove all possible sources of ignition. Avoid prolonged breathing of vapor.
Contain spill with inert absorbent.
WASTE DISPOSAL: Dispose of in accordance with local, state, and federal regulations.
=======================================================================================
SECTION VIII - PROTECTION INFORMATION
==========================================================================================
RESPIRATORY PROTECTION: With general room ventilation does not require any respiratory protection. If room ventilation is
lacking, use NIOSH approved respirator, if necessary.
VENTILATION: Use adequate ventilation in volume and pattern to keep TLV/PEL below recommended levels.
PROTECTIVE GLOVES: To prevent prolonged exposure, use neoprene or equivalent gloves
EYE PROTECTION: Safety Glasses or goggles with splash guards or side shields.
OTHER PROTECTIVE EQUIPMENT: Wear protective clothing as required to prevent skin contact.
==========================================================================================
SECTION IX - HANDLING AND STORAGE PRECAUTIONS
==========================================================================================
STORAGE AND HANDLING: Use with adequate ventilation. HARMFUL OR FATAL IF SWALLOWED! AVOID CONTACT
WITH EYES AND SKIN. AVOID BREATHING VAPORS. FLAMMABLE! Do not store the product above 100oF/38oC. Do not
flame, cut, braze weld or melt empty containers. Keep the product away from heat, open flame, and other sources of ignition. Avoid
contact with strong acids, alkalis and oxidizers.
PDF created with pdfFactory trial version www.softwarelabs.com
Page 3 of 3 White Glazing Putty
==========================================================================================
SECTION X - ADDITIONAL INFORMATION
==========================================================================================
SHIPPING INFORMATION: Please comply with DOT regulations in USA
HMIS RATING: Health 2 4 = Extreme
Fire 4 3 = High
Reactivity 1 2 = Moderate
Personal Protection - 1 = Slight
See Section VIII 0 = Insignificant
==========================================================================================
CALIFORNIA PROPOSITION 65:
WARNING: This product contains Toluene, a chemical known to the State of California to cause birth defects or other reproductive
harm.
SARA 313 SUPPLIER NOTIFICATION:
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning
and Community Right-To-Know Act of 1986 and 40 CFR 372:
CAS NUMBER CHEMICAL NAME % BY WEIGHT
108-88-3 Toluene 12-14%
1330-20-7 Xylene 2-4 %
78-93-3 Methyl Ethyl Ketone < 1%
This information must be included on all MSDS that are copied and distributed for this material.
==========================================================================================
ABBREVIATIONS:
IARC = International Agency for Research N/AV = Not Available
on Cancer
ACGIH =American Conference of Governmental N/AP = Not Applicable
Industrial Hygienists
NIOSH =National Institute of Occupational N/E = Not Established
Safety and Health
DOT = Department of Transportation N/D = Not Determined
TLV = Threshold Limit Value PEL = Permissible Emission Level
NTP = National Toxicology Program
===============================================================================
PREPARED BY: U. S. CHEMICAL & PLASTICS
600 Nova Dr SE
Massillon, OH 44646
TELEPHONE 330-830-6000
DATE REVIEWED: January 12, 2006
DATE REVISED: February 18, 2004
REVISION: Sections II, X
The information in the Material Safety Data Sheet has been compiled from our experience and data presented in various technical
publications. It is the user's responsibility to determine the suitability of this information for the adoption of the safety precautions as
may be necessary. We reserve the right to revise Material Safety Data Sheets from time to time as new technical information becomes
available. The user has the responsibility to contact the Company to make sure that the sheet is the latest one issued.
PDF created with pdfFactory trial version www.softwarelabs.com
|