CHEMTRONICS MSDS #4001
SECTION 1: CHEMICAL PRODUCT AND COMPANY INFORMATION
Company Address:
8125 Cobb Center Drive
Kennesaw, GA 30152
Product Information: 800-TECH-401 Emergency: (Chemtrec) 800-424-9300
Customer Service: 800-645-5244 Revision Date: February 12, 2004
Product Identification
CIRCUITWORKS CONDUCTIVE PEN
Product Code: CW2200MTP, CW2200STP, CW2200BLK
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS No. Wt. % Range
Silver 7440-22-4 35.0-65.0
Propylene Glycol Methyl Ether Acetate 108-65-6 2.0-20.0
Ethylene Glycol Monobutyl Ether Acetate 112-07-2 2.0-20.0
n-Butyl Acetate 123-86-4 5.0-35.0
Acrylic Resin mixture 15.0-40.0
SECTION 3: HAZARDOUS IDENTIFICATION
Emergency Overview: Silver colored paint with an aromatic hydrocarbon odor. This product is flammable. Liquid and vapors will irritate eyes and skin. Breathing
high concentrations of product may produce headache, nausea, and drowsiness.
Potential Health Effects:
Eyes: Vapors of this product may irritate the eyes. Liquid is irritating and may cause tearing, redness, swelling or temporary corneal damage.
Skin: Contact may cause irritation. prolonged contact may cause dermatitis.
Ingestion: Harmful if swallowed. May cause nervous system depression.
Inhalation: Harmful if inhaled. May cause headache, nausea, vomiting, dizziness, drowsiness, irritation of the respiratory tract/mucous membranes. Extreme over-
exposure may cause loss of consciousness and narcosis.
Pre-Existing Medical Conditions Aggravated by Exposure: Heart, lung, eye, skin.
SECTION 4: FIRST AID MEASURES
Eyes: Immediately flush with large amounts of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes. Have eyes
examined by a Physician if discomfort persists.
Skin: Remove contaminated clothing and wash skin with soap and water. Get medical attention if irritation develops or persists. Wash clothing separately before
reuse.
Ingestion: If swallowed, give two or more glasses of water immediately. DO NOT induce vomiting. Get medical attention.
Inhalation: In case of exposure to high concentrations of vapor or mist, remove to fresh air. If breathing is difficult, give oxygen and call a Physician. If breathing has
stopped, apply artificial respiration and call a Physician.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point: 76癋 (TCC) LEL/UEL: 1.5/10.0 (% by volume in air)
Extinguishing Media: Use alcohol foam, water foam, carbon dioxide, dry chemical, or water spray. Water may not be effective in fighting the fire but can be used to
cool overheated areas. Care must be taken to not spread the fire.
Fire Fighting Instructions: Remove all ignition sources. Use water spray to cool overheated containers. Take care not the spread fire with water. As in any fire, wear
self-contained breathing apparatus (pressure demand, OSHA/NIOSH approved or equivalent) and full protective gear. Solvent vapors are an explosion hazard. Keep
material away from all sources of ignition, extreme heat, sparks or open flame. Material can be easily ignited and burns with intense heat.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Large Spills: Remove all sources of ignition (sparks, open flames, etc.). Wear self-contained breathing apparatus and appropriate personal protective equipment.
Ventilate area and contain and absorb spill with inert material. Collect spill by scooping up liquids and absorbent material and place in a chemical waste container for
proper disposal. Do not flush to sewer. Prevent material from entering storm sewers, ditches that lead to waterways and ground.
Small Spills: Absorb spill with absorbent material, then place in a chemical waste container for proper disposal.
SECTION 7: HANDLING AND STORAGE
Avoid prolonged or repeated contact with skin, eyes or clothing. Wash hands before eating. Use with adequate ventilation. Avoid breathing product vapor. Do not
reuse this container. Store in a cool dry place, away from heat, sparks or flames. Keep container tightly closed when not in use. Do not store in direct sunlight.
KEEP OUT OF REACH OF CHILDREN.
SECTION 8: EXPOSURE CONTROLS, PERSONAL PROTECTION
Exposure Guidelines:
CHEMICAL NAME ACGIH TLV OSHA PEL ACGIH STEL
Silver 0.1 mg/m3 0.01mg/m3 NA
Propylene Glycol Methyl Ether Acetate NA NA NA
Ethylene Glycol Monobutyl Ether Acetate NA NA NA
n-Butyl Acetate 150 ppm 150 ppm 200 ppm
Acrylic Resin NA NA NA
Work/Hygienic Practices: Good general ventilation should be sufficient to control airborne levels. Local exhaust ventilation may be necessary to control any air
contaminants to within their TLVs during the use of this product. If vapor concentration exceeds TLV, use NIOSH approved organic vapor cartridge respirator. Wear
safety glasses with side shields or goggles and rubber or other chemically resistant gloves when handling this material.
NFPA and HMIS Codes: NFPA HMIS
Health 2 2
Flammability 3 3
Reactivity 1 1
Personal Protection - B
Page 1 of 2
CHEMTRONICS MSDS #4001
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Silver colored paint Solubility in Water: > 10%
Odor: Aromatic hydrocarbon Specific Gravity: 1.8-2.0
pH: NA Evaporation Rate: >1
Vapor Pressure: 5-6 mmHg @ 20癈 (Butyl acetate=1)
Percent Volatile: 30-40% Boiling Range: 259-378癋
Vapor Density: >1 (Air = 1)
SECTION 10: STABILITY AND REACTIVITY
Stability: This product is stable. Conditions to Avoid: Avoid heat, sparks, open flame and strong oxidizing conditions.
Incompatibility: Do not mix strong oxidizers, acids, bases, caustics, amines and alkali contamination.
Products of Decomposition: Decomposition may release carbon monoxide, carbon dioxide, oxides of nitrogen, monomers and smoke. Depending on conditions, some
highly reactive peroxides may be formed.
Hazardous Polymerization: Will not occur. Material is not known to polymerize.
Conditions to avoid: NA
SECTION 11: TOXICOLOGICAL INFORMATION
LD50 LD50 LC50
Ingredients (rat) Oral (rbt) Dermal (rat) Inhalation
Silver >10000 mg/kg (mouse) 5,000 mg/kg
Propylene Glycol Methyl Ether Acetate 8,500 mg/kg >5000 mg/kg >4300 ppm
Ethylene Glycol Monobutyl Ether Acetate 2400 mg/kg 500 mg/24H MLD
n-Butyl Acetate 10,768 mg/kg 500 mg/24H MLD 2000 ppm/4H
Acrylic Resin NA NA NA
Cancer Information: No ingredients listed as human carcinogens by NTP or IARC
Reproductive effects: none Teratogenic effects: none Mutagenic effects: none
SECTION 12: ECOLOGICAL INFORMATION
Environmental Impact Information
Avoid runoff into storm sewers and ditches which lead to waterways. Water runoff can cause environmental damage.
REPORTING
US regulations require reporting spills of this material that could reach any surface waters. The toll free number for the US Coast Guard National Response Center is:
1-800-424-8802
SECTION 13: DISPOSAL CONSIDERATIONS
Dispose of in accordance with all federal, state and local regulations. Water runoff can cause environmental damage.
SECTION 14: TRANSPORTATION INFORMATION
Proper Sub. Pkg. Hazard Pkg. Max.
Shipping Name UN Number Class Risk Group Label Instr. Quantity
Air: PAINT UN1263 3 - III Flammable Y309 1L
Liquid 5L
Ground: Consumer Commodity - ORM-D - - ORM-D 173.150 5L
ORM-D
SECTION 15: REGULATORY INFORMATION
SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-To- Know
Act of 1986 (40 CFR 372).
Silver CAS# 7440-22-4 35.0-65.0%
This information should be included on all MSDSs copied and distributed for this material.
TOXIC SUBSTANCES CONTROL ACT (TSCA).
All ingredients of this product are listed on the TSCA Inventory.
WHMIS: Class B2; Class D2B
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all of the information required by the CPR.
SECTION 16: OTHER INFORMATION
Normal ventilation for standard manufacturing practices is usually adequate. Local exhaust should be used when large amounts are released.
To the best of our knowledge, the information contained herein is accurate. However, all materials may present unknown hazards and should be used with caution. In
particular, improper use of our products and their inappropriate combination with other products and substances may produce harmful results which cannot be
anticipated. Final determination of the suitability of any material is the sole responsibility of the user. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that may exist.
Page 2 of 2
|