Material Safety Data Sheet CS: 1.4.22
1 of 4
Page:
ACRDW Issue Date :May 2008
Infosafe NoTM ISSUED by HILTI CS: 1.4.22
Product Name :HILTI HVU ADHESIVE CAPSULE
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER
HILTI HVU ADHESIVE CAPSULE
Product Name
HILTI(AUST.) PTY LTD
Company Name
1G Homebush Bay Drive, Rhodes 2138
Address
Tel: (02) 8748-1000
Telephone/Fax
Fax: (02) 8748-1190
Number
Not available.
Recommended Use
2-component foil capsule with liquid and powder.
Additional
Information
2. HAZARDS IDENTIFICATION
HAZARDOUS SUBSTANCE.
Hazard
NON-DANGEROUS GOODS.
Classification
Hazard classification according to the criteria of NOHSC.
Dangerous goods classification according to the Australia Dangerous Goods
Code.
Risk Phrase(s) R36 Irritating to eyes.
R43 May cause sensitization by skin contact.
Safety Phrase(s) S26 In case of contact with eyes, rinse immediately with plenty of water and
seek medical advice.
S28 After contact with skin, wash immediately with plenty of soap and water.
S3 Keep in a cool place.
S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Name CAS Proportion
Ingredients
Balance
Other ingredients
determined not to
be hazardous
27813-02-1 < 10%
Hydroxypropyl
methacrylate
94-36-0 < 2%
Dibenzoyl
peroxide
Other Information Chemical comoposition: Adhesive anchor, contains urethane methacrylate resin
with reactive diluent, dibenzoyl peroxide, phlegmatized.
4. FIRST AID MEASURES
Inhalation If inhaled, remove from contaminated area. Apply artificial respiration if not
breathing. If symptoms develop seek medical attention.
Ingestion Do NOT induce vomiting. Wash out mouth with water. If symptoms develop seek
medical attention.
Skin Remove contaminated clothing. Wash skin with soap and water. If symptoms
develop seek medical advice.
Eye If contact with the eye(s) occurs, wash with copious amounts of water for at
least 15 minutes holding eyelid(s) open. Take care not to rinse contaminated
water into the non-affected eye. Seek medical advice.
Eye wash and normal washroom facilities.
First Aid Facilities
5. FIRE FIGHTING MEASURES
Carbon dioxide, dry chemical, foam, water spray.
Suitable
Extinguishing Media
Under fire conditions this product may emit toxic and/or irritating fumes
Hazards from
including oxides of carbon and nitrogen.
Combustion
Products
Specific Hazards Classified as a Class C1 (COMBUSTIBLE LIQUID) for the purposes of storage and
handling, in accordance with the requirements of AS1940. This product should
Print Date: 28/05/2008 CS: 1.4.22
Material Safety Data Sheet CS: 1.4.22
2 of 4
Page:
ACRDW Issue Date :May 2008
Infosafe NoTM ISSUED by HILTI CS: 1.4.22
Product Name :HILTI HVU ADHESIVE CAPSULE
be stored and used in a well ventilated area away from naked flames, sparks
and other sources of ignition.
Component B: Decomposition begins above +50癈
Decomposition
Temp.
Fire-fighters should wear full protective clothing and self contained
Precautions in
breathing apparatus (SCBA) operated in positive pressure mode.
connection with Fire
6. ACCIDENTAL RELEASE MEASURES
Remove ignition sources. Ensure adequate ventilation or wear self-contained
Emergency
breathing apparatus. Wear full protective clothing and avoid contact with skin
Procedures
and eyes. Take up by mechanical means. Remove remainder with solvent or inert,
non-combustible absorbent such as vermiculite, sand or dirt. Dispose of
according to relevant local, state and federal government regulations.
7. HANDLING AND STORAGE
Use in a well ventilated area. DO NOT store or use in confined spaces. Build
Precautions for Safe
up of mists or vapours in the atmosphere must be prevented. Avoid breathing in
Handling
spray or mists or vapours. Repeated or prolonged skin exposure without
protection should be prevented in order to lessen the possibility of skin
disorders. Observe expiry date. Do not use damaged capsules. It is essential
that all who come into contact with this material maintain high standards of
personal hygiene ie. washing hands prior to eating, drinking, smoking or using
toilet facilities.
Store in a well ventilated area away from sources of heat and ignition. Keep
Conditions for Safe
away from direct sunlight. Store in original packing in a cool (max. +25癈)
Storage
and dark place. This product should be stored away from foodstuffs and
oxidizing agents. For information on the design of the store-room reference
should be made to Australian Standard AS1940 - The storage and handling of
flammable and combustible liquids. Reference should also be made to any
relevant Commonwealth, State or Territory regulations.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Name TWA
STEL
National Exposure
Standards
mg/m3 ppm mg/m3 ppm Footnote
Dibenzoyl peroxide 5
No biological limit allocated.
Biological Limit
Values
No exposure standards have been established for this material by the National
Other Exposure
Occupational Health And Safety Commission (NOHSC). However, exposure standards
Information
for ingredients are stated above:
As published by the National Occupational Health and Safety Commission
(NOHSC):
TWA - the Time-Weighted Average airborne concentration over an eight-hour
working day, for a five-day working week over an entire working life.
STEL (Short Term Exposure Limit) - the average airborne concentration over a
15 minute period which should not be exceeded at any time during a normal
eight-hour workday.
Ensure sufficient ventilation to maintain airborne concentrations below
Engineering
exposure limits and prevent exposure to vapours, mists and fumes.
Controls
If engineering controls are not effective in controlling airborne exposure
Respiratory
then respiratory protective equipment should be used suitable for protecting
Protection
against airborne contaminants. Final choice of appropriate breathing
protection is dependant upon actual airborne concentrations and the type of
breathing protection required will vary according to individual circumstances.
Expert advice may be required to make this decision. Reference should be made
to Australian/New Zealand Standards AS/NZS 1715, Selection, Use and
maintenance of Respiratory Protective Devices; and AS/NZS 1716, Respiratory
Protective Devices.
Print Date: 28/05/2008 CS: 1.4.22
Material Safety Data Sheet CS: 1.4.22
3 of 4
Page:
ACRDW Issue Date :May 2008
Infosafe NoTM ISSUED by HILTI CS: 1.4.22
Product Name :HILTI HVU ADHESIVE CAPSULE
Eye Protection Safety glasses with side shields, goggles or full-face shield as appropriate
recommended. Final choice of appropriate eye/face protection will vary
according to individual circumstances i.e. methods of handling or engineering
controls and according to risk assessments undertaken. Eye protection should
conform with Australian/New Zealand Standard AS/NZS 1337 - Eye Protectors for
Industrial Applications.
Hand Protection Wear gloves of impervious material such as PVC or rubber gloves. Final choice
of appropriate gloves will vary according to individual circumstances i.e.
methods of handling or according to risk assessments undertaken. Reference
should be made to AS/NZS 2161.1: Occupational protective gloves - Selection,
use and maintenance.
Body Protection Suitable protective clothing should be worn e.g. cotton overalls buttoned at
neck and wrist.
9. PHYSICAL AND CHEMICAL PROPERTIES
2-component foil capsule with liquid and powder.
Appearance
Ester-like.
Odour
Component B: Decomposition begins above +50癈
Decomposition
Temperature
Not available
Melting Point
Not available
Boiling Point
Solubility in Water Component A: 107 g/L @ 25癈 (HPMA)
Component B: insoluble
Not applicable
pH Value
Component A: < 0.1 mbar @ 20癈 (HPMA)
Vapour Pressure
Viscosity Component A: < 300 mPa.s @ 23癈 (DIN 53 015)
Efflux time 4 mm nozzle: 22s @ 23癈 (DIN 53 211)
Efflux time 4 mm nozzle: ---
Colour Component A (resin): yellowish liquid.
Component B (hardener): white powder.
Density Component A (resin): 1.1 g/cm?br>
Component B (hardener): 1.3 g/cm?@ 20癈
Component A: > 100癈 (DIN 53 213)
Flash Point
This product is not self-igniting.
Auto-Ignition
Temperature
Not available
Flammable Limits -
Lower
Not available
Flammable Limits -
Upper
Other Information Changes in condition:
Component A: polymerisation > 110癈.
Component B: decomposition temperature dibenzoyl peroxide > 50癈.
Bulk density:
Component B: 0.6 kg/cm?
10. STABILITY AND REACTIVITY
Stable under normal use conditions.
Chemical Stability
Conditions to Avoid - At storage temperatures above 30癈, dibenzoyl peroxide in component B
decomposes/degrades and the resulting carbon dioxide makes the capsule swell.
- Exposure to direct sunlight can cause the resin to polymerise. This makes
the adhesive anchor unusable.
Strong oxidizing agents.
Incompatible
Materials
Print Date: 28/05/2008 CS: 1.4.22
Material Safety Data Sheet CS: 1.4.22
4 of 4
Page:
ACRDW Issue Date :May 2008
Infosafe NoTM ISSUED by HILTI CS: 1.4.22
Product Name :HILTI HVU ADHESIVE CAPSULE
None, if used for the intended purpose.
Hazardous
Decomposition
Products
Will not occur.
Hazardous
Polymerization
11. TOXICOLOGICAL INFORMATION
No toxicology data available for this product.
Toxicology
Information
Inhalation of vapours or mists may irritate the respiratory system.
Inhalation
Ingestion may irritate the gastric tract causing nausea and vomiting.
Ingestion
Skin Skin contact may cause irritation. May cause sensitization in some
individuals.
Eye contact will cause irritation.
Eye
Prolonged or repeated skin contact may cause irritation.
Chronic Effects
12. ECOLOGICAL INFORMATION
No data available for this specific product.
Ecotoxicity
Not available.
Persistence /
Degradability
Not available.
Mobility
Keep away from drains, surface water, ground water and soil.
Environ. Protection
13. DISPOSAL CONSIDERATIONS
Dispose of according to relevant local, state and federal government
Disposal
regulations. Foil capsules that have become unusable (e.g. expiry date
Considerations
exceeded) must be disposed of as special waste in accordance with legislation.
14. TRANSPORT INFORMATION
Not classified as a Dangerous Good according to the Australian Code for the
Transport
Transport of Dangerous Goods by Road and Rail.
Information
15. REGULATORY INFORMATION
Not Scheduled
Poisons Schedule
Irritant
Hazard Category
16. OTHER INFORMATION
MSDS Reviewed: May 2008
Date of preparation
MSDS Created: May 2003
or last revision of
MSDS
Contact Person/Point For further information call Hilti (Aust) Pty. Ltd. on: (02) 8748 1000
(Business Hours).
...End Of MSDS...
?Copyright ACOHS Pty Ltd
Copyright in the source code of the HTML, PDF, XML, XFO and any other electronic files rendered by an Infosafe system for Infosafe MSDS displayed on this site is the
intellectual property of Acohs Pty Ltd.
Copyright in the layout, presentation and appearance of each Infosafe MSDS displayed on this site is the intellectual property of Acohs Pty Ltd.
The compilation of MSDS's displayed on this site is the intellectual property of Acohs Pty Ltd.
Copying of any MSDS displayed on this site is permitted for personal use only and otherwise is not permitted. In particular the MSDS's displayed on this site cannot be
copied for the purpose of sale or licence or for inclusion as part of a collection of MSDS without the express written consent of Acohs Pty Ltd.
Print Date: 28/05/2008 CS: 1.4.22
|