Material Safety Data Sheet
EpoxAmite 100 Resin and EpoxAmite 101 Hardener
Date of Preparation: February 11, 2010 MSDS No. 30AB
Revision: 0001
Section 1 - Chemical Product and Company Identification
Product/Chemical Name: EpoxAmite 100 Resin
Other Designations: Formulated Epoxy
General Use: Laminating, Adhesive and Casting Resin
Manufacturer: Smooth-On Inc., 2000 St. John St., Easton PA 18042
Phone (610) 252-5800, FAX (610) 252-6200
Emergency Contact: Chem-Tel
Domestic 800-255-3924
International 813-248-0585
Section 2- Hazards Identification
Not hazardous according to United States Occupational Safety and Health Administration HMIS
(OSHA) Hazard Communication Standard (29 CFR 1910.1200), the Canadian Workplace 1
H
Hazardous Materials Information System (WHMIS) and Council directive 1999/45/EC and 1
F
its subsequent amendments. 0
R
Section 3 - Composition / Information on Ingredients
No hazardous ingredients
Section 4 - First Aid Measures
Inhalation: Remove to fresh air: if breathing is labored seek medical attention.
Eye Contact: Flush with water for 15 minutes: seek medical attention
Skin Contact: Remove with soap and water: if redness or rash develops seek medical attention:
Launder contaminated clothing before reuse.
Ingestion: seek medical attention
After first aid, get appropriate in-plant, paramedic, or community medical support.
Section 5 - Fire-Fighting Measures
Flash Point: >485 ?(252 ?br>
F C) NFPA
Flash Point Method: PMCC
Flammability Classification: Non-Flammable 1
Extinguishing Media: Foam, Dry Chemical, and Carbon Dioxide 1 0
Unusual Fire or Explosion Hazards: None
0
Hazardous Combustion Products: Oxides of Nitrogen and Carbon, Acids
and Aldehydes when burned.
Fire-Fighting Instructions: Do not release runoff from fire control methods to sewers or waterways.
Fire-Fighting Equipment: Because fire may produce toxic thermal decomposition products, wear a
self-contained breathing apparatus (SCBA) with a full-face piece operated in pressure-demand or
positive-pressure mode.
MSDS No. 30AB EpoxAmite 100 Resin and EpoxAmite 101 Hardener Revision: 0001
Section 6 - Accidental Release Measures
Spill /Leak Procedures
Containment: Dike and contain for later disposal. Do not release into sewers or waterways.
Cleanup: Scrape up excess.
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Section 7 - Handling and Storage
Handling Precautions: Avoid prolonged or repeated skin contact. Use good general housekeeping
procedures.
Storage Requirements: Store in Closed containers. Use only with adequate ventilation.
Section 8 - Exposure Controls / Personal Protection
Respiratory Protection: Follow OSHA respirator regulations 29 CFR 1910.134 and European
Standard EN 149; wear an MSHA/NIOSH or European Standard EN149 approved respirator.
Protective Clothing/Equipment: Wear chemically protective gloves to prevent prolonged or repeated
skin contact. Wear protective eyeglasses or chemical safety goggles, per OSHA eye- and face-
protection regulations 29 CFR 1910.133 and European Standard EN166. Contact lenses are not eye
protective devices. Appropriate eye protection must be worn instead of, or in conjunction with contact
lenses.
Comments: Never eat, drink, or smoke in work areas. Practice good personal hygiene after using this
material, especially before eating, drinking, smoking, using the toilet, or applying cosmetics
Section 9 - Physical and Chemical Properties
Physical State: Liquid Water Solubility: negligible
Appearance and Odor: Water-White to Boiling Point: None (Polymeric Resin)
Yellow; Faint Epoxy Odor Freezing/Melting Point: None (Polymeric
Vapor Pressure: None (Polymeric Resin) Resin)
Vapor Density (Air=1): None (Polymeric Evaporation Rate: None (Polymeric Resin)
Resin) Viscosity: 10 poise
Specific Gravity (H2O=1, at 4 ?1.14
C):
Section 10 - Stability and Reactivity
Stability: This product is stable at room temperature in closed containers under normal storage and
handling conditions.
Polymerization: Hazardous polymerization cannot occur.
Chemical Incompatibilities: Strong oxidizing agents, strong Lewis or mineral acids.
Conditions to Avoid: Mixing with Amines under uncontrolled conditions.
Hazardous Decomposition Products: Thermal oxidative decomposition of Epoxy Resin EEW-190
can produce: Oxides of Nitrogen and Carbon, Acids and Aldehydes when burned.
Page 2
MSDS No. 30AB EpoxAmite 100 Resin and EpoxAmite 101 Hardener Revision: 0001
Section 11- Toxicological Information
Carcinogenicity: None
Eye Effects: Irritation
Mutagenicity: None Determined
Skin Effects: Irritation
Teratogenicity: None Determined
Section 12 - Ecological Information
None Determined
Section 13 - Disposal Considerations
Disposal: Contact your supplier or a licensed contractor for detailed recommendations. Follow
applicable Federal, state, and local regulations.
Section 14 - Transport Information
DOT IATA IMDG
Not Regulated Not Regulated Not Regulated
Section 15 - Regulatory Information
EPA Regulations: This material in not considered a hazardous material.
RCRA Hazardous Waste Number: Not listed (40 CFR 261.33): None
RCRA Hazardous Waste Classification (40 CFR 261): Not classified
CERCLA Hazardous Substance (40 CFR 302.4) unlisted specific per RCRA, Sec. 3001; CWA, Sec.
311 (b)(4); CWA, Sec. 307(a), CAA, Sec. 112
CERCLA Reportable Quantity (RQ), None
SARA 311/312 Codes: None
SARA Toxic Chemical (40 CFR 372.65): None
SARA EHS (Extremely Hazardous Substance) (40 CFR 355): Not listed,
TSCA Inventory Status (40CFR710): All components of this formula are on the TSCA inventory
California Proposition 65: This product does not intentionally contain any chemicals which have been
identified by the state of California to cause cancer, birth defects or other reproductive harm.
Page 3
MSDS No. 30AB EpoxAmite 100 Resin and EpoxAmite 101 Hardener Revision: 0001
16 - Other Information
Disclaimer: The information contained in this MSDS is considered accurate as of the version date.
However, no warranty is expressed or implied regarding the accuracy of the data. Since the use of
this product is not within the control of Smooth-On Inc., it is the user's obligation to determine the
suitability of the product for its intended application and assumes all risk and liability for its safe use.
This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health
Administration (OSHA)Hazard Communication Standard (29 CFR 1910.1200), the Canadian Workplace
Hazardous Materials Information System (WHMIS), and European Union Directive 1907/2006/EEC (REACH).
Hazard symbols and risk phrases are based on maximum listed concentration of each hazardous ingredient.
Unlisted ingredients are not "hazardous" per the OSHA Hazard Communication Standard (29 CFR
1910.1200), the Canadian Workplace Hazardous Materials Information System (WHMIS) or the European
Union (EU/EEC) directive 1907/2006/EEC and are considered trade secrets under US Federal Law (29CFR
and 40CFR), Canadian Law (Health Canada Legislation), and European Union Directives
Page 4
Material Safety Data Sheet
EpoxAmite 100 Resin and EpoxAmite 101 Hardener
Date of Preparation: February 11, 2010 MSDS No. 30AB
Revision: 0001
Section 1 - Chemical Product and Company Identification
Product/Chemical Name: EpoxAmite 101 Hardener
Other Designations: Curing Agent, Epoxy
General Use: Laminating, Adhesive and Casting Resin
Manufacturer: Smooth-On Inc., 2000 St. John St., Easton PA 18042
Phone (610) 252-5800, FAX (610) 252-6200
Emergency Contact: Chem-Tel
Domestic 800-255-3924
International 813-248-0585
Section 2- Hazards Identification
Hazard Designation:
HMIS
Europe Canada 2
H
1
F
0
R
T:Toxic C: Corrosive
Risk Phrases pertaining to particular dangers
R48/20/21/22: Harmful: danger of serious damage to health by prolonged exposure through
inhalation, in contact with skin and if swallowed.
R23/24: Toxic by inhalation and in contact with skin.
R34: Irritating to skin.
R41: Risk of serious damage to eyes.
R43: May cause sensitization by skin contact.
R68: Possible risks of irreversible effects.
Classified according to Articles 6 & of Directive 1999/45/EC
Section 3 ?Composition / Information on Ingredients
Component ACGIH TWA Exposure Limits Hazard Designation Weight Percent
OSHA PEL (%)
Teta, reaction products with
60-65
None Established None Established Not Classified
phenol/formaldehyde
CAS Number: 32610-77-8
EINECS Number: none
Triethylenetetramine
20-25
None Established None Established
CAS Number: 112-24-3
C
EINECS Number: 203-950-6
Phenol
5 ppm/19mg/m3 5 ppm/19mg/m3 15-20
CAS Number: 108-95-2
T C
EINECS Number: 203-632-7
MSDS No. 30AB EpoxAmite 100 Resin and EpoxAmite 101 Hardener Revision: 0001
Section 4 - First Aid Measures
Inhalation: Remove too fresh air; if breathing is labored seek medical attention.
Eye Contact: Flush with water for 15 minutes; seek medical attention
Skin Contact: remove with soap and water: if redness or rash develops seek medical attention:
Launder contaminated clothing before reuse.
Ingestion: do not induce vomiting; seek medical attention
After first aid, get appropriate in-plant, paramedic, or community medical support.
Section 5 - Fire-Fighting Measures
Flash Point: 280 ?(135.6?br>
F C) NFPA
Flammability Classification: Combustible Liquid, Class III
1
Extinguishing Media: Foam, Dry Chemical, and Carbon Dioxide
Unusual Fire or Explosion Hazards: None 2 0
Hazardous Combustion Products: May generate Ammonia gas, Oxides of Nitrogen and
0
Carbon when burned
Fire-Fighting Instructions: Do not release runoff from fire control methods to sewers or
waterways.
Fire-Fighting Equipment: Because fire may produce toxic thermal decomposition products, wear a
self-contained breathing apparatus (SCBA) with a full face piece operated in pressure-demand or
positive-pressure mode.
Section 6 - Accidental Release Measures
Spill /Leak Procedures
Containment: Dike and contain for later disposal. Do not release into sewers or waterways.
Cleanup: Cover minor spills with sodium bisulfate to neutralize and reduce vapors. Spray with water.
Place in metal containers for recovery or disposal. Clean-up personnel must be equipped with self-
contained breathing apparatus and butyl rubber protective clothing.
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Section 7 - Handling and Storage
Handling Precautions: Avoid prolonged or repeated eye and skin contact. Avoid breathing vapors
and use only with adequate ventilation. Use good general housekeeping procedures.
Storage Requirements: Keep away from oxidizers. Store in Closed containers. Use only with
adequate ventilation.
Section 8 - Exposure Controls / Personal Protection
Respiratory Protection: Follow OSHA respirator regulations 29 CFR 1910.134 and European
Standard EN 149; wear an MSHA/NIOSH or European Standard EN149 approved respirator.
Warning! Air-purifying respirators do not protect workers in oxygen-deficient atmospheres. If
respirators are used, OSHA requires a written respiratory protection program that includes at least:
medical certification, training, fit-testing, periodic environmental monitoring, maintenance, inspection,
cleaning, and convenient, sanitary storage areas
Protective Clothing/Equipment: Wear chemically protective gloves, boots, and aprons to prevent
prolonged or repeated skin contact. Wear protective eyeglasses or chemical safety goggles, per
OSHA eye- and face-protection regulations 29 CFR 1910.133 and European Standard EN166.
Contact lenses are not eye protective devices. Appropriate eye protection must be worn instead of,
or in conjunction with contact lenses.
Page 6
MSDS No. 30AB EpoxAmite 100 Resin and EpoxAmite 101 Hardener Revision: 0001
Section 8 - Exposure Controls / Personal Protection (continued)
Comments: Never eat, drink, or smoke in work areas. Practice good personal hygiene after using this
material, especially before eating, drinking, smoking, using the toilet, or applying cosmetics.
Section 9 - Physical and Chemical Properties
Physical State: Water Solubility: 0.25 g/l
Appearance and Odor: Amber liquid, Boiling Point: >446?(>230?br>
F C)
Phenolic odor Freezing/Melting Point: No Data
Vapor Pressure: <1 mm/Hg @ 21? C Evaporation Rate: No Data
Vapor Density (Air=1): No Data pH: 10
Specific Gravity (H2O=1, at 4 癈): 1.08
Section 10 - Stability and Reactivity
Stability: This material is stable at room temperature in closed containers under normal storage and
handling conditions.
Polymerization: Hazardous polymerization cannot occur.
Chemical Incompatibilities: Strong oxidizing agents, strong Lewis or mineral acids.
Conditions to Avoid: Mixing with epoxies under uncontrolled conditions.
Hazardous Decomposition Products: Thermal oxidative decomposition of can produce: Ammonia
gas, Oxides of Nitrogen and Carbon when burned. Combustion of product under oxygen-starved
conditions can be expected to produce numerous toxic products including nitriles, cyanic acid,
isocyanates, cyanogens, nitrosamines, amides, and carbamates.
Section 11- Toxicological Information
Mutagenicity: No Data
Eye Effects: can cause burns
Teratogenicity: No Data
Skin Effects: will cause burns
Acute Toxicity Effects Data:
Oral LD50 (rat): >2,200 mg/kg
Dermal LD50 (rat): >2000 mg/kg
Skin LD50 (rat) > 20 mg/l
Section 12 - Ecological Information
None Determined
Section 13 - Disposal Considerations
Disposal: Contact your supplier or a licensed contractor for detailed recommendations. Follow
applicable Federal, state, and local regulations.
Section 14 - Transport Information
DOT IATA IMDG
Not Regulated Not Regulated Not Regulated
Section 15 - Regulatory Information
EPA REGULATIONS:
SARA Title III Section 313 (40 CFR 372)
Chemical Name CAS # % by Weight
Phenol 108-95-2 20% Max
Page 7
MSDS No. 30AB EpoxAmite 100 Resin and EpoxAmite 101 Hardener Revision: 0001
Section 15 - Regulatory Information (continued)
TSCA Inventory Status (40CFR710): All components of this formula are on the TSCA inventory
California Proposition 65: This product does not intentionally contain any chemicals, which have been
identified by the state of California to cause cancer, birth defects or other reproductive harm.
Canadian Regulations;
WHMIS Identification: D2
CDSL/NDL (Canadian Domestic Substance List/Non Domestic Substance List): Listed on CDSL
Labeling according to EEC Directive
Risk Phrases Symbol(s) Required for EU Label Safety Phrases
R48/20/21/22: Harmful: S1/2: Keep locked up and
danger of serious damage to out of reach of children
health by prolonged exposure S26: In case of contact with
through inhalation, in contact eyes, rinse immediately with
with skin and if swallowed. plenty of water and seek
R23/24: Toxic by inhalation medical advice
T: Toxic
and in contact with skin. S28: After contact with skin,
R38: Irritating to skin. wash immediately with plenty
R41: Risk of serious damage of soap and water.
to eyes. S38: In case of insufficient
R43: May cause ventilation, wear suitable
sensitization by skin contact. respiratory equipment.
C: Corrosive
S45: In case of an accident
R68: Possible risks of
irreversible effects. or if you feel sick , seek
medical attention
16 - Other Information
Disclaimer: The information contained in this MSDS is considered accurate as of the version date.
However, no warranty is expressed or implied regarding the accuracy of the data. Since the use of
this product is not within the control of Smooth-On Inc., it is the user's obligation to determine the
suitability of the product for its intended application and assumes all risk and liability for its safe use.
This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety
and Health Administration (OSHA)Hazard Communication Standard (29 CFR 1910.1200), the
Canadian Workplace Hazardous Materials Information System (WHMIS), and European Union
Directive 1907/2006/EEC (REACH). Hazard symbols and risk phrases are based on maximum listed
concentration of each hazardous ingredient. Unlisted ingredients are not "hazardous" per the OSHA
Hazard Communication Standard (29 CFR 1910.1200), the Canadian Workplace Hazardous
Materials Information System (WHMIS) or the European Union (EU/EEC) directive 1907/2006/EEC
and are considered trade secrets under US Federal Law (29CFR and 40CFR), Canadian Law
(Health Canada Legislation), and European Union Directives.
Page 8
|