Telephone: (716) 282-6950
MATERIAL SAFETY DATA SHEET
Fax: (716) 282-6971
4011 Hyde Park Blvd.
P. O. Box 1075
JANUARY 2010
Niagara Falls, NY 14302-1075
SECTION I ?MATERIAL IDENTIFICATION
BLACK EPDXY PCWDER
Trade/Material Name:
SECTION 2. HAZARDOUS INGREDIENTS
OSHA ACG-111
CAS No. PEL TLV
Phenol 108-95-2 < 3 5 PPm 5 ppm
10
Fiberglass 65997-17-3 >10-<50 5 rug/m3
/?
(Bound in Polymer Respirable Nuisance Dust
M t i ) Lime
Hydrated 1305-62-0 < 3 5 mg/me 5 mg/m3
10
7631-86-9 <20 80 m g/m3
Amorphous Silica
% SiO, 0.1
< 1 0.1 mg/m3
Crystalline Silica 14808-60-7 mg/In'
Carbon Black* 1333-86-4 < 1 3.5 mg/m' 3.5
mg/in'
*See Section V
SECTION 3. PHYSICAL DATA
Boiling Point NA Specific Gravity: 1.5 -2.0
Vapor Pressure: Negligible @ 20癈 Evaporation Rate: NA
Solubility in Negligible pH: NA
Water:
Appearance: Black or Blue- Odor: Mild & Characteristic
Green Pellets
SECTION 4. EXPLOSION HAZARD DATA
Flash Point: NA Flammable Limits: NA LelNA Uel
Method Used: NA
Extinguishing Media:X Water Fog Foam X CO2
X Dry Chemical Other
Special Fire Fighting Procedures:
Unusual Fire and Explosion Hazards:
Hazardous Decomposition Products:
Autoignition Temperature:
Firefighters should be equipped with a self-contained breathing apparatus
as decomposition in a fire may produce toxic fumes.
None known.
Telephone: (716) 282-6950
MATERIAL SAFETY DATA SHEET
Fax: (716) 282-6971
4011 Hyde Park Blvd.
P. O. Box 1075
JANUARY 2010
Niagara Falls, NY 14302-1075
May include: phenol, formaldehyde, ammonia, carbon monoxide., carbon
dioxide, hydrogen cyanide, particulate matter, and other organic compounds
including benzo(a)pyrene.
None known.Call poison control center, hospital emergency room or physician
immediately.
SECTION 5. HEALTH HAZARD DATA
Effects of Overexposure:
Phenol, formaldehyde, and ammonia vapors may be released during molding
processes. Overexposure to these vapors may cause irritation to eyes, nose,
throat, and skin. Allergic skin reactions may be experienced by sensitized
individuals. Exposure to dust from machining operations may cause nose and
throat irritation. Fiberglass component is a continuous filament fiber and
considered a mechanical irritant and nuisance dust.
*IARC has listed carbon black as a Class 2B possible human carcinogen based
on laboratory studies with animals.
FIRST AID PROCEDURES
Remove to fresh air. If respiration stops, apply appropriate emergency
resuscitation techniques. Get medical attention.
Flush eyes with a large amount of water for at least 15 minutes. Call a
physician if irritation persists.
Wash affected areas with soap and water at first opportunity.
If accidentally swallowed, dilute by drinking large quantities of water.
Immediately contact poison control center or hospital emergency room for
any other treatment directions.
Inhalation:
Eye Contact:
Skin Contact: Ingestion:
SECTION 6. REACTIVITY DATA
Stability:___X___ Stable Unstable
Conditions to Avoid:NA
Incompatibility: NA (Materials to Avoid)
Hazardous Polymerization:May Occur X Does Not Occur
Hazardous Decomposition: May occur during fire or at very high temperatures
(see Section IV for hazardous products generated).
Telephone: (716) 282-6950
MATERIAL SAFETY DATA SHEET
Fax: (716) 282-6971
4011 Hyde Park Blvd.
P. O. Box 1075
JANUARY 2010
Niagara Falls, NY 14302-1075
SECTION 7. SPECIAL PROTECTION INFORMATION
Respiratory Protection: Use NIOSH/MSHA approved respiratory protection if
level of air contaminants exceed action levels set by OSHA.
Ventilation:
Local Exhaust: At points of emission to maintain exposure below OSHA action
levels.
Mechanical (General): General room ventilation should be present.
Eye Protection:Wear safety glasses with side shields,
Protective Clothing:Impervious gloves should be worn to prevent skin
contact (neoprene, latex, rubber, milled nitrite, butyl).
SECTION 8. ENVIRONMENTAL DATA
nvironmental Toxicity Data: NA
Waste Disposal Method: In accordance with all local, state, and federal
regulations (landfill).
Container Disposal: In accordance with all local, state, and federal
regulations (landfill).
This product contains the following toxic chemicals subject to the
reporting requirements of Section 313 of the Emergency Planning and
Community Right-To-Know Act of 1986 and 40 CFR 372:
EXTREMELY
HAZARDOUS PERCENT BY
CAS # CHEMICAL NAME SI.,THS TAN CF.WEIGHT
108-95-2 Phenol Yes < 3
SECTION 10. SPILL OR LEAK PROCEDURES
Response to Spills: Sweep or vacuum spills. To minimize dust, vacuum
cleaning is preferred.
Reportable Quantity:NE
SECT
Recommended Storage Practice and Conditions:
Other Precautions:
Keep container closed and sealed when not in use. Store in cool, dry place
below 77癋 (25'C).
Avoid breathing fumes from molding or other heating operations. Avoid
breathing dust from cutting, machining, or deburring operations. Avoid high
concentrations of dust in air and accumulation of dust on equipment. A fine
dust of this material can create a dust explosion hazard.
NA = Not Applicable NE = Not Established
DATE: JANUARY 2004
THE INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED ACCURATE.
HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF
THESE DATA OR THE RESULT TO BE OBTAINED FROM THE USE THEREOF.
METLAB CORPORATION ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR
PROPERTY
DAMAGE TO VENDEES, USERS OR THIRD PARTIES CAUSED BY THE MATERIAL. SUCH
VENDEES OR USERS ASSUME ALL RISKS ASSOCIATED WITH THE USE OF THE MATERIAL.
|