MATERIAL SAFETY DATA SHEET PROD #.: 1800
MSDS DATE: 4/24/02
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: FLEXIBLE BUMPER COAT (BLACK)
IES PART NUMBER: 1800
MANUFACTURER: INTERNATIONAL EPOXIES & SEALERS
ADDRESS: 30241 COMMERCE DRIVE
SAN ANTONIO, FL 33576
24 HOUR EMERGENCY PHONE (INFOTRAC) (800) 535-5053
INFORMATION PHONE: (800) 451-7206
DATE PREPARED: APRIL 24, 2002
SECTION 1 NOTES: This material safety data sheet complies with OSHA'S Hazard Communication Standard,
1910.1200. If any item is not applicable (N/A) or no information is available (N/I), the space is marked to indicate
that.
SECTION 2: COMPOSITION / INFORMATION ON INGREDIENTS
WT. PERCENT OCCUPATIONAL EXPOSURE LIMITS
INGREDIENT: CAS NO. IS LESS THAN TLV-TWA TLV-STEL PEL-TWA PEL-CEILING SKIN
METHYL ETHYL KETONE 78-93-3 45.0% 200 ppm 300 ppm 200 ppm 300 ppm YES
TOULENE 108-88-3 20.0% 50 ppm N/E 100 ppm 150 ppm YES
ACETONE 67-64-1 10.0% 750 ppm 1000 ppm 750 ppm 1000 ppm YES
METHYL AMYL KETONE 110-43-0 10.0% 50 ppm N/E 100 ppm N/E YES
1-METHOXY-2-PROPANOL
ACETATE 108-65-6 5.0% N/E N/E N/E N/E YES
CRYSTALLINE SILICA 14808-60-7 5.0% 0.1 mg/M3 N/E 0.1 mg/M3 N/E NO
ETHYL 3-ETHOXY-
PROPIONATE 763-69-9 5.0% N/E N/E N/E N/E YES
CARBON BLACK 1333-86-4 5.0% 3.05 ppm N/E N/E N/E NO
ETHYLBENZENE 100-41-4 1.0% 100 ppm 125 ppm 100 ppm N/E YES
SECTION 2 NOTES: (See Section XIII for abbreviation legend)
SECTION 3: PHYSICAL DATA
APPEARANCE: Black liquid
ODOR: Solvent
BOILING POINT: 133 ?to 337?F (56.1?to 169.4?C)
VAPOR DENSITY (AIR = 1): Is heavier than air
SPECIFIC GRAVITY (H2O = 1): 0.9106
EVAPORATION RATE: Is slower than Butyl Acetate
SOLUBILITY IN WATER: Insoluble in H2O
PERCENT VOLATILE:
BY WT = 78.6% BY VOL = 84.3%
VOLATILE ORGANIC COMPOUNDS (VOC):
LBS/GAL: 5.88
GRAMS/LTR: 705
SECTION 4: FIRE AND EXPLOSION HAZARD DATA
Page 1 of 4
MATERIAL SAFETY DATA SHEET PROD #.: 1800
MSDS DATE: 4/24/02
FLASH POINT FLAMMABLE LIMITS IN AIR, UPPER:
13.1%
F: 10?F (% BY VOLUME) LOWER: 1.0%
F: 10?F (12.2?C)
(Tagliabue closed cup)
EXTINGUISHING MEDIA: CO2 Dry Chemical Foam Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS: Keep containers tightly closed when not in use. Vapors
are heavier than air and can travel long distances to a source of ignition. Isolate from excessive heat,
open flame, sparks and electrical equipment. Application of this product to hot surfaces requires special
precautions. Closed containers may explode due to pressure build-up when exposed to extreme heat.
Follow label warnings until container has been thoroughly cleaned or destroyed.
SPECIAL FIRE FIGHTING PROCEDURES: Wear full protective equipment, including self-contained
breathing apparatus. Water may be used to cool unruptured containers to prevent pressure build-up and
possible autoignition or explosion.
SECTION 5: HEALTH HAZARDS DATA
EFFECTS OF OVEREXPOSURE:
EYES: May cause severe irritation, redness, tearing and blurred vision.
SKIN: Prolonged or repeated contact may cause irritation, defatting and dermatitis. May be
harmful if absorbed through skin.
INHALATION: Vapors may irritate mucous membranes and cause headaches, nausea,
dizziness, vomiting, fatigue and/or impairment of coordination.
INGESTION: May cause nausea, vomiting, irritation and/or diarrhea.
EFFECTS OF OVEREXPOSURE- CHRONIC HEALTH HAZARDS: Chronic exposure to high
concentrations of hazardous material in this product may cause loss of appetite, diarrhea, nose bleeds,
encephalopathy and neural disfunctions. Cancer hazard: This product contains crystalline silica, which
can cause cancer. The risk of cancer depends on the level and duration of exposure.
WARNING! This product contains a chemical known to the State of California to cause cancer, birth
defects, or other reproductive harm.
FIRST AID MEASURES
EYES: Flush eyes immediately with large amounts of fresh water for at least 15 minutes. Obtain
medical treatment.
SKIN: Wash affected areas of skin with soap and water. Remove all contaminated clothing.
Consult a physician if irritation persists.
INGESTION: Drink 1-2 large glasses of water to dilute. DO NOT INDUCE VOMITING! If vomiting
does occur, keep head below hips to prevent aspiration of material into lungs, as
even small amounts may cause chemical pneumonitis, pulmonary edema and/or
hemorrhage. Never give anything by mouth to an unconscious person. Call a
physician or poison control center immediately. Induce vomiting as directed by
medical personnel.
INHALATION: Remove too fresh air and, if necessary, restore breathing. Treat symptomatically
and consult a physician.
PRIMARY ROUTES OF ENTRY: Skin contact Skin absorption Inhalation Eye contact
SECTION 6; REACTIVITY DATA
HAZARDOUS DECOMPOSITION PRODUCTS: Smoke, carbon monoxide, carbon dioxide and other
potentially toxic gases may be released when this product is heated to decomposition. Overexposure to
Page 2 of 4
MATERIAL SAFETY DATA SHEET PROD #.: 1800
MSDS DATE: 4/24/02
these decomposition products may cause a health hazard. Symptoms may not be immediately apparent.
Obtain medical attention.
CONDITIONS TO AVOID (STABILITY): High temperature, sources or ignition and poor ventilation.
INCOMPATIBILITY (MATERIAL TO AVOID): Strong oxidizers, acids and caustics.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal conditions
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Evacuate non-essential
personnel from immediate area and remove all sources of ignition. Ventilate area if possible and avoid
breathing vapors. Wear a respirator while collecting material with inert absorbent and non-sparking
tools. Large spills beyond normal maintenance should be collected by trained emergency response
personnel.
WASTE DISPOSAL METHOD: Dispose of material in accordance with federal, state and local regulations.
Refer to hazard caution statements in Sections IV, V, and VI.
SECTION 8: SAFE HANDLING AND USE INFORMATION
RESPIRATORY PROTECTION: If ventilation is not adequate to reduce vapors below the listed
requirement in Section II, use a self-contained, positive-pressure breathing apparatus or a NIOSH/MSHA
approved respirator for organic vapors. The user must be properly fitted and trained to assure effective
protection.
VENTILATION : Sufficient ventilation, in volume and pattern, should be provided to keep the air
contaminant concentration below the current OSHA Permissible Exposure Limit (PEL) or ACGIH
Threshold Limit Value (TLV). Heavy solvent vapors should be removed from the lower levels of the work
area. All ignition sources, including non-explosion proof equipment, should be eliminated. Remove all
decomposition products formed during welding or flame cutting of surfaces coated with this product.
EYE PROTECTION: Use safety glasses with splash guards or side shields, splash goggles or face
shield.
SKIN PROTECTION: Use solvent-impervious gloves for prolonged or repeated contact.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: A protective apron or solvent-impervious clothing is
recommended for splash protection. Wear chemical resistant footwear.
WORK HYGIENIC PRACTICES: Wash hands and face before eating, drinking, using tobacco products
or using the bathroom. Remove and wash contaminated clothing before reuse. Do not reuse
contaminated footwear unless they are decontaminated. Store personal items, such as cigarettes and
gum, away from the work area.
SECTION 9: SPECIAL PRECAUTIONS
HANDLING AND STORAGE: EXTREMELY FLAMMABLE LIQUID! Keep container tightly closed when not
in use. Ground all holding and transfer containers. Avoid storage above 120癋 or near fire or open flame.
Do not transfer to unlabeled containers.
OTHER PRECAUTIONS: For industrial use only. Reports have associated repeated or prolonged
occupational overexposure to solvents with permanent brain damage. Intentional misuse by deliberately
concentrating and inhaling the contents of this product may be harmful or fatal.
SECTION 10: HMIS RATINGS
HMIS HAZARD CLASSIFICATION
HEALTH: 2 FLAMMABILITY: 3 REACTIVITY: 0
Page 3 of 4
MATERIAL SAFETY DATA SHEET PROD #.: 1800
MSDS DATE: 4/24/02
SECTION 11: OTHER REGULATIONS
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
313 REPORTABLE INGREDIENTS: This product contains the following substances subject to the
reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act
of 1986 and 40 CFR Part 372:
CHEMICAL NAME CAS NUMBER WT/WT % IS LESS THAN
METHYL ETHYL KETONE 78-93-3 45.0 %
TOLUENE 108-88-3 20.0 %
ETHYLBENZENE 100-41-4 1.0 %
TOXIC SUBSTANCES CONTROL ACT: This product contains the following chemical substances
subject to the reporting requirements of TSCA 12(B) if exported from the United States.
CHEMICAL NAME CAS NUMBER
ACETONE 67-64-1
ISOPROPANOL 67-63-0
METHYL ISOBUTYL KETONE 108-10-1
n-BUTYL ACETATE 123-86-4
N-BUTANOL 71-36-3
ISOBUTANOL 78-83-1
CALIFORNIA PROPOSITION 65:
WARNING: The chemical (s) noted below and contained in this product are known to the state of
California to cause cancer, birth defects or other reproductive harm.
CHEMICAL NAME CAS NUMBER
TOLUENE 108-88-3
SECTION 12: OTHER INFORMATION
OTHER INFORMATION:
LEGEND: N.A. - Not applicable
N.D. - Not determined
N.E. - Not established
PREPARATION INFORMATION:
DISCLAIMER: The information and recommendations provided herein are believed to be accurate as of the date
hereof. However, such information and recommendations are provided without warranty of any kind and
International Epoxies & Sealers disclaims any and all liability or legal responsibility or use or reliance upon
same.
Page 4 of 4
|