M102-0411 Pre-catalyzed Aerosol Finish Flat
FR102-0411
M102-0411
S82.1642
102-0411
MATERIAL SAFETY DATA SHEET
RPM Wood Finishes Group
3194 Hickory Boulevard
Hudson, North Carolina 28638
828-728-8266
EMERGENCY PHONE (CHEM TREC): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-800-424-9300
FOR ALL INTERNATIONAL TRANSPORTATION ACCIDENTS. . . . . . . . . . . . . . . . .1-703-527-3887 (collect)
Health: 2 Flammability: 4 Reactivity 0
PRODUCT NAME: M102-0411 Pre-catalyzed Aerosol Finish Flat
I. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
REVISION DATE: 23/01/03
SUPERCEDES: 04/01/02
MSDS NO. M102-0411
II. COMPOSITION/INFORMATION ON INGREDIENTS
CHEMICAL NAME % CAS # PEL
n-Butyl acetate 21-30 123-86-4 150 ppm TWA; 710 mg/m3 TWA
isobutanol 11-20 78-83-1 100 ppm TWA; 300 mg/m3 TWA
Propane 11-20 74-98-6 1000 ppm TWA; 1800 mg/m3 TWA
acetone 11-20 67-64-1 1000 ppm TWA; 2400 mg/m3 TWA
Isobutane 1-10 75-28-5 No PEL established
propylene glycol monomethyl ether 1-10 107-98-2 No PEL established
isopropanol 1-10 67-63-0 400 ppm TWA; 980 mg/m3 TWA
toluene 1-10 108-88-3 200 ppm TWA; C 300 ppm
Cellulose Nitrate, Cellulose Ester 1-10 9004-70-0 No PEL established
xylene, mixed isomers 1-10 1330-20-7 100 ppm TWA; 435 mg/m3 TWA
sec-Butyl alcohol <1 78-92-2 150 ppm TWA; 450 mg/m3 TWA
ethylbenzene <1 100-41-4 100 ppm TWA; 435 mg/m3 TWA
m-xylene <1 108-38-3 No PEL established
o-xylene <1 95-47-6 No PEL established
p-xylene <1 106-42-3 No PEL established
formaldehyde <1 50-00-0 0.75 ppm TWA
III. HAZARDS IDENTIFICATION
Inhalation., Eye contact., Skin contact., Absorption., Ingestion.
Routes of Entry:
Skin disease including eczema and sensitization. Respiratory disease including
Medical Conditions Aggravated:
asthma and bronchitis. Eye disease. Kidney disease. Liver disease. Digestive tract
disease.
M102-0411 Pre-catalyzed Aerosol Finish Flat Page 1 of 7
Immediate (Acute) Health Effects
Irritation may be delayed for several hours. Can cause severe respiratory irritation,
Inhalation:
dizziness, weakness, fatigue, nausea, headache and possible unconsciousness.
Substance causes moderate skin irritation. Moderately irritating to the skin. Can cause
Skin Contact:
minor skin irritation, defatting, and dermatitis.
Irritating but will not permanently injure eye tissue. Can cause moderate irritation,
Eye Contact:
tearing and reddening, but not likely to permanently injure eye tissue. Contact with
the eyes may cause moderate to severe eye injury. Eye contact may result in tearing
and reddening, but not likely to permanently injure eye tissue. Temporary vision
impairment (cloudy or blurred vision) is possible.
Component(s) may be absorbed through intact skin, but it is unlikely that harmful
Skin Absorption:
affects will occur unless contact is prolonged, repeated, and extensive. Can be
absorbed through the skin but exposure must be extensive before adverse health
effects occur. Toxic and may be harmful if absorbed through the skin; may produce
target organ damage. Minimal hazard in normal industrial use. May cause
gastrointestinal discomfort.
Aspiration of material into the lungs can cause chemical pneumonitis which can be
Ingestion:
fatal. Irritating to mouth, throat, and stomach. Can cause abdominal discomfort,
nausea, vomiting and diarrhea.
Target Organ Acute Toxicity:
n-Butyl acetate eyes, skin, respiratory system, CNS
Isobutyl alcohol eyes, skin, respiratory system, CNS
Propane CNS
Acetone respiratory system, skin, eyes, CNS
Isobutane CNS
Propylene glycol monomethyl ether eyes, skin, respiratory system, CNS
Isopropyl alcohol eyes, skin, respiratory system
Toluene CNS, liver, kidneys, skin, eyes, respiratory system
Xylenes (o-, m-, p- isomers) CNS, eyes, blood, liver, kidneys, skin, GI tract, respiratory system
n-Butyl alcohol eyes, CNS, skin, respiratory system
Ethyl benzene eyes, respiratory system, skin, CNS
m-Xylene CNS, eyes, blood, liver, kidneys, skin, GI tract, respiratory system
o-Xylene CNS, eyes, blood, liver, kidneys, skin, GI tract, respiratory system
p-Xylene CNS, eyes, blood, liver, kidneys, skin, GI tract, respiratory system
Formaldehyde (and formalin) eyes, skin, respiratory system, nasal cancer
Long-Term (Chronic) Health Effects:
OSHA. Contains a substance that is a probable cancer hazard based on human
Carcinogenicity:
studies.
Possible reproductive hazard. A component in this product has been shown to cause
Reproductive and Developmental
Toxicity: birth defects and reproductive disorders in laboratory animals at doses that could be
encountered in the workplace.
No data available to indicate product or any components present at greater than 0.1%
Mutagenicity:
is mutagenic or genotoxic.
M102-0411 Pre-catalyzed Aerosol Finish Flat Page 2 of 7
Upon prolonged and/or repeated exposure, can cause severe respiratory irritation,
Inhalation:
dizziness, weakness, fatigue, nausea, headache and possible unconsciousness.
Prolonged or repeated contact may cause irritation. May cause lingering affects but
Skin Contact:
not likely to result in permanent damage if the exposure is eliminated. Upon
prolonged or repeated contact, can cause moderate skin irritation, defatting, and
dermatitis. Not likely to cause permanent damage.
Upon prolonged or repeated contact, can cause severe irritation. Eye contact may
Eye Contact:
result in corneal injury. Symptoms may include discomfort or pain, excess blinking
and tear production, with marked redness and swelling of the conjunctiva. Temporary
vision impairment (cloudy or blurred vision) is possible.
Upon prolonged or repeated exposure, toxic if absorbed through the skin. Likely to
Skin Absorption:
cause systemic damage.
Skin. Respiratory Tract. Nervous System. Eyes. Kidneys. Liver. Digestive Tract.
Target Organ Chronic Toxicity:
Blood.
No additional health information available.
Supplemental Health Hazard
Information:
IV. FIRST AID
Remove to fresh air. If breathing is difficult, have a trained individual administer
Inhalation:
oxygen. If not breathing, give artificial respiration and have a trained individual
administer oxygen. Get medical attention immediately.
Immediately flush eyes with plenty of water for at least 20 minutes retracting eyelids
Eyes:
often. Tilt the head to prevent chemical from transferring to the uncontaminated eye.
Get immediate medical attention and monitor the eye daily as advised by your
physician.
Wash with soap and water. Get medical attention if irritation develops or persists.
Skin Contact:
Wash with soap and water under a drench shower. Remove contaminated clothing,
launder immediately, and discard contaminated leather goods. Get medical attention
immediately.
No hazard in normal industrial use. Do not induce vomiting. Seek medical attention
Ingestion:
if symptoms develop. Provide medical care provider with this MSDS.
No additional first aid information available.
Notes to MD:
V. FIRE FIGHTING MEASURES
Flammability Summary:
12.8 @ 77?F
Upper Flammable/Explosive
Limit, % in air:
0.8 @ 77?F
Lower Flammable/Explosive
Limit, % in air:
Flammable Liquid. Can release vapors that form explosive mixtures at temperatures at
Fire Hazards:
or above the flash point. Vapors may be ignited by heat, sparks, flames or other
sources of ignition at or above the low flash point giving rise to a Class B fire. Vapors
are heavier than air and may travel to a source of ignition and flash back.
M102-0411 Pre-catalyzed Aerosol Finish Flat Page 3 of 7
Use alcohol foam, carbon dioxide, or water spray when fighting fires involving this
Extinguishing Media:
material. Flammable component(s) of this material may be lighter than water and burn
while floating on the surface. Use alcohol resistant spray, Carbon Dioxide, water
spray or dry chemical to extinguish a fire involving this chemical. Use alcohol
resistant foam, carbon dioxide, or dry chemical extinguishing agents. Water spray or
fog may also be effective for extinguishing if swept across the base of the fire. Water
can also be used to absorb heat and keep exposed material from being damaged by
fire.
Flammable component(s) of this material may be lighter than water and burn while
Fire Fighting Instructions:
floating on the surface.Do not enter fire area without proper protection including self-
contained toxic breathing apparatus and full protective equipment. Fight fire from a
safe distance and a protected location due to the potential of hazardous vapors and
decomposition products. Flammable component(s) of this material may be lighter than
water and burn while floating on the surface. Use water spray/fog for cooling.
Hazardous Combustion Products: Toxic gases Carbon dioxide, Carbon monoxide Hydrogen cyanide Nitrogen
containing gases
VI. ACCIDENTAL RELEASE MEASURES
Exposure to the spilled material may be irritating or harmful. Follow personal
Health Consideration for Spill
Response: protective equipment recommendations found in Section VIII of this MSDS.
Additional precautions may be necessary based on special circumstances created by
the spill including; the material spilled, the quantity of the spill, the area in which the
spill occurred. Also consider the expertise of employees in the area responding to the
spill.
Prevent the spread of any spill to minimize harm to human health and the
Spill Mitigation Procedures
General Methods: environment if safe to do so. Wear complete and proper personal protective
equipment following the recommendation of Section VIII at a minimum. Dike with
suitable absorbent material like granulated clay. Gather and store in a sealed container
pending a waste disposal evaluation.
VII. HANDLING AND STORAGE
Wash thoroughly after handling. Avoid contact with material. Use spark-proof tools
Handling:
and explosion-proof equipment. "Empty" containers retain product residue (liquid
and/or vapor) and can be dangerous. Remove contaminated clothing and wash before
reuse. Harmful or irritating material. Avoid contact and avoid breathing the material.
Use only in a well ventilated area.
Keep away from sources of ignition. Keep away from heat, sparks, and flame. Store in
Storage:
a cool place in original container and protect from sunlight. Store in a cool dry
ventilated location. Isolate from incompatible materials and conditions. Keep
container(s) closed.
VIII. ENGINEERING CONTROLS AND PERSONAL PROTECTIVE EQUIPMENT
Ventilation should effectively remove and prevent buildup of any vapor/mist/fume
Engineering Controls:
generated from the handling of this product. Explosion proof exhaust ventilation
should be used. Local exhaust ventilation or other engineering controls are normally
required when handling or using this product to avoid overexposure.
M102-0411 Pre-catalyzed Aerosol Finish Flat Page 4 of 7
Protective Equipment
Respirators should be selected by and used under the direction of a trained health and
Respiratory Tract:
safety professional following requirements found in OSHA's respirator standard (29
CFR 1910.134) and ANSI's standard for respiratory protection (Z88.2-1992). A
written respiratory protection program, including provisions for medical certification,
training, fit testing, exposure assessments, maintenance, inspection, cleaning, and
convenient, sanitary storage should be implemented.
Wear chemically resistant safety glasses with side shields when handling this product.
Eyes:
Wear additional eye protection such as chemical splash goggles and/or face shield
when the possibility exists for eye contact with splashing or spraying liquid, or
airborne material. Do not wear contact lenses. Have an eye wash station available.
Avoid skin contact by wearing chemically resistant gloves, an apron and other
Skin:
protective equipment depending upon conditions of use. Inspect gloves for chemical
break-through and replace at regular intervals. Clean protective equipment regularly.
Wash hands and other exposed areas with mild soap and water before eating,
drinking, and when leaving work.
IX. PHYSICAL DATA
Cloudy Liquid
Physical State:
Strong Solvent
Odor:
6.0000
Solids Vol %:
9.0000
Solids Wt %:
4.91
Material VOC lbs/gal:
589.91
Material VOC gms/l:
6.4115
Weight per gallon:
X. STABILITY AND REACTIVITY
Stable. Normally stable. Keep away from heat, sparks and flame.
Stability Information:
Avoid: heat, sparks, flame and oxidizing agents. None known.
Conditions to Avoid:
Strong oxidizing agents. Strong alkalies. Strong acids. Amines. Acids. Acetic
Chemical Incompatibility:
anhydride. Peroxides. Oxidizing materials.
XI. TOXICOLOGICAL INFORMATION
Chemical Name CAS Number LD50/LC50
Acetic acid, butyl ester 123-86-4 Inhalation LC50 Rat : 2000 ppm/4H; Inhalation LC50 Mouse : 6 gm/m3/2H;
Oral LD50 Rat : 10768 mg/kg; Oral LD50 Mouse : 6 gm/kg; Dermal LD50
Rabbit : >17600 mg/kg
Isobutyl alcohol 78-83-1 Oral LD50 Rat : 2460 mg/kg; Dermal LD50 Rabbit : 3400 mg/kg
Acetone 67-64-1 Inhalation LC50 Rat : 50100 mg/m3/8H; Inhalation LC50 Mouse : 44
gm/m3/4H; Oral LD50 Rat : 5800 mg/kg; Oral LD50 Mouse : 3 gm/kg
Propane, 2-methyl- 75-28-5 Inhalation LC50 Rat : 57 pph/15M
2-Propanol, 1-methoxy- 107-98-2 Inhalation LC50 Rat : 10000 ppm/5H; Oral LD50 Mouse : 11700 mg/kg;
Dermal LD50 Rabbit : 13 gm/kg
Isopropyl alcohol 67-63-0 Inhalation LC50 Rat : 16000 ppm/8H; Oral LD50 Rat : 5045 mg/kg; Oral
LD50 Mouse : 3600 mg/kg; Dermal LD50 Rabbit : 12800 mg/kg
Toluene 108-88-3 Inhalation LC50 Rat : 49 gm/m3/4H; Inhalation LC50 Mouse : 400 ppm/24H;
Oral LD50 Rat : 636 mg/kg; Dermal LD50 Rabbit : 14100 uL/kg
Nitrocellulose 9004-70-0 Oral LD50 Rat : >5 gm/kg; Oral LD50 Mouse : >5 gm/kg
Xylene 1330-20-7 Inhalation LC50 Rat : 5000 ppm/4H; Oral LD50 Rat : 4300 mg/kg; Dermal
LD50 Rabbit : >1700 mg/kg
M102-0411 Pre-catalyzed Aerosol Finish Flat Page 5 of 7
sec-Butyl alcohol 78-92-2 Inhalation LC50 Rat : 8000 ppm/4H; Oral LD50 Rat : 790 mg/kg; Oral LD50
Mouse : 2680 mg/kg; Dermal LD50 Rabbit : 3400 mg/kg
Benzene, ethyl- 100-41-4 Oral LD50 Rat : 3500 mg/kg; Dermal LD50 Rabbit : 17800 uL/kg
m-Xylene 108-38-3 Oral LD50 Rat : 5 gm/kg; Dermal LD50 Rabbit : 14100 uL/kg
p-Xylene 106-42-3 Inhalation LC50 Rat : 4550 ppm/4H; Oral LD50 Rat : 5 gm/kg
Formaldehyde 50-00-0 Inhalation LC50 Rat : 203 mg/m3; Inhalation LC50 Mouse : 454 gm/m3/4H;
Oral LD50 Rat : 100 mg/kg; Oral LD50 Mouse : 42 mg/kg; Dermal LD50
Rabbit : 270 uL/kg
XII. ECOLOGICAL INFORMATION
Keep out of waterways. Moderate ecological hazard. This product may be dangerous
Overview (for ingredients):
to plants and/or wildlife.
XIII. DISPOSAL CONSIDERATIONS
The waste may be a listed and/or characteristic hazardous waste. Spent or discarded
Waste Description for Spent
Product: material is a hazardous waste.
Comply with all Local, State, Federal, and Provincial Environmental Regulations.
Disposal Methods:
Dispose of by incineration following Federal, State, Local, or Provincial regulations.
If discarded, this product is considered a RCRA ignitable waste, D001.
Potential EPA Waste Codes:
Components Subject to USEPA Land Disposal Restrictions:
Isobutyl alcohol 78-83-1 17.33 %
Acetone 67-64-1 13.84 %
Toluene 108-88-3 3.42 %
Xylenes (o-, m-, p- isomers) 1330-20-7 1.3 %
n-Butyl alcohol 78-92-2 0.68 %
Ethyl benzene 100-41-4 0.43 %
XIV. TRANSPORTATION INFORMATION
Aerosols, flammable 2.1 UN1950
DOT
XV. REGULATORY INFORMATION
Chemical Name Regulation CASRN %
Isopropyl alcohol SARA 313 Reportable: 67-63-0 4.49
Toluene SARA 313 Reportable: 108-88-3 3.42
Xylene (mixed isomers) SARA 313 Reportable: 1330-20-7 1.3
sec-Butyl alcohol SARA 313 Reportable: 78-92-2 0.68
Ethyl benzene SARA 313 Reportable: 100-41-4 0.43
m-Xylene SARA 313 Reportable: 108-38-3 0.17
o-Xylene SARA 313 Reportable: 95-47-6 0.07
p-Xylene SARA 313 Reportable: 106-42-3 0.04
Formaldehyde SARA 313 Reportable: 50-00-0 0.01
Phosphoric acid SARA 313 Reportable: 7664-38-2 0.00
Formaldehyde Extremely Haz. Substances: 50-00-0 0.01
TPQ = 500 pounds; RQ = 100 pounds SARA Threshold Planning Quantity: 50-00-0 0.01
(does not meet toxicity criteria but
because of high production volume and
recognized toxicity is considered a
chemical of concern)
50-00-0 0.01
Formaldehyde (gas) California Proposition 65 Cancer List:
108-88-3 3.42
Toluene California Proposition 65
Developmental Toxicity:
123-86-4 22.06
n-Butyl acetate New Jersey Right To Know:
78-83-1 17.33
isobutanol New Jersey Right To Know:
M102-0411 Pre-catalyzed Aerosol Finish Flat Page 6 of 7
74-98-6 14.74
Propane New Jersey Right To Know:
67-64-1 13.84
acetone New Jersey Right To Know:
75-28-5 6.68
Isobutane New Jersey Right To Know:
XVI. ADDITIONAL INFORMATION
IMPORTANT: WHILE THE DESCRIPTIONS, DATA AND INFORMATION
Other Information:
CONTAINED HEREIN ARE PRESENTED IN GOOD FAITH AND BELIEVED TO BE
ACCURATE, IT IS PROVIDED FOR YOUR GUIDANCE ONLY. BECAUSE MANY
FACTORS MAY AFFECT PROCESSING OR APPLICATION/USE, WE RECOMMEND
THAT YOU PERFORM AN ASSESSMENT TO DETERMINE THE SUITABILITY OF A
PRODUCT FOR YOUR PARTICULAR PURPOSE PRIOR TO USE. NO WARRANTIES
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED, DATA
OR INFORMATION SET FORTH. IN NO CASE SHALL THE DESCRIPTIONS,
INFORMATION,OR DATA PROVIDED BE CONSIDERED A PART OF OUR TERMS
AND CONDITIONS OF SALE. FURTHER, THE DESCRIPTIONS, DATA AND
INFORMATION FURNISHED HEREUNDER ARE GIVEN GRATIS. NO OBLIGATION
OR LIABILITY FOR THE DESCRIPTION, DATA AND INFORMATION GIVEN ARE
ASSUMED. ALL SUCH BEING GIVEN AND ACCEPTED AT YOUR RISK.
MSDS glossary.
M102-0411 Pre-catalyzed Aerosol Finish Flat Page 7 of 7
|