SECTION X - HMIS RATINGS



HMIS RATINGS - HEALTH: 3                 FLAMMABILITY: 0                    REACTIVITY : 0





                           SECTION XI - OTHER REGULATIONS



SARA SECTION 313:

This product contains the following substances subject to the reporting requirements of Section

313 of the Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40

CFR Part 372:



--------CHEMICAL NAME-----------       CAS NUMBER            WT/ WT % IS LESS THAN



ALIPHATIC POLYISOCYANATE                      N/A                              90.0%





PREVIOUS MSDS REVISION DATE: 01/ 30 / 04



LEGEND: N. A. - Not Applicable, N. E.           -   Not Established,

        N. D. - Not Determined









The information contained on this MSDS is to the best of our knowledge and

belief, accurate. However, since the conditions of handling and use are beyond

our control, we make no guarantee of results, and assume no liability for damage

incurred by use of this material. It is the responsibility of the user to comply with

all applicable federal, state and local laws and regulations.









       < END OF MSDS >

                                   MATERIAL SAFETY DATA SHEET



                   SECTION I - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION



PRODUCT NAME                             : CHEM LOCK PART B

IDENTIFICATION NUMBER                    : M7307B                                                 DATE PRINTED: 03/12/04

PRODUCT USE/ CLASS                       :



SUPPLIER:                                                            MANUFACTURER:

FAR FROM NORMAL                                                      T. J. RONAN PAINT CORPORATION

 1318 39TH ST. NW                                                       749 EAST 135TH ST.

 FARGO, ND 58102                                                        BRONX, NY 10454



CHEMTREC: ( 800) 424- 9300                                           CHEMTREC : ( 800 ) 424-9300

24 HOUR EMERGENCY HOTLINE                                            24 HOUR EMERGENCY HOTLINE



PREPARER: JD, PHONE : 718-292-1100, PREPARE DATE: 01/30/04



                       SECTION II - COMPOSITION/ INFORMATION ON INGREDIENTS



                                                                WT. PERCENT -------------------OCCUPATIONAL EXPOSURE LIMITS ------------

-----------CHEMICAL NAME-------------CAS NUMBER     IS LESS THAN    TLV- TWA     TLV- STEL        PEL- TWA PEL- CEILING    SKIN







ALIPHATIC POLYISOCYANATE                N/A                90. 0 %   .005 mg / M 3     1 . 0 mg / M 3                           YES

METHOXY- ETHYL ESTER                     763-69-9          15. 0 %      NO INFO       NO INFO                                   NO



(SEE SECTION 11 FOR ABBREVIATION LEGEND)



                                             SECTION III - PHYSICAL DATA



BOILING RANGE                  : 169- 169 F                          VAPOR DENSTIY                 : Is heavier than air

ODOR                           : AROMATIC                            SPECIFIC GRAVITY              : 1.1611

APPERANCE                      : CLEAR LIQUID                        EVAPORATION RATE              : Is slower than Ether

SOLUBILITY IN H20              : YES

VOLATILE BY WEIGHT             : 12 . 5 %                            VOLATILE BY VOLUME : 15 . 3%

VOCS, lbs / gal                : 1 . 21                              VOCS, grams / l t r : 145



(See Section XI for abbreviation legend)



                             SECTION IV - FIRE AND EXPLOSION HAZARD DATA



 FLASH POINT: 138 F                                                            LOWER EXPLOSIVE LIMIT: 1 . 1 %

( TAGLIABUE CLOSED CUP )                                                       UPPER EXPLOSIVE LIMIT: 12. 1 %



EXTINGUISHING MEDIA: CO2 DRY CHEMICAL FOAM

 UNUSUAL FIRE AND EXPLOSION HAZARDS:          SOLVENT VAPORS MAY BE HEAVIER THAN

AIR. STAGNANT AIR MAY CAUSE VAPORS TO ACCUMULATE AND TRAVEL ALONG THE GROUND TO

AN IGNITION SOURCE WHICH MAY RESULT IN A FLASH BACK TO THE SOURCE OF THE VAPORS.

ISOLATE FROM HEAT, ELECTRICAL EQUIPMENT , SPARKS AND OPEN FLAME.

                                                                  ( Continued on Page 2 )

Product: M7307B               Preparation Date: 01/ 30 / 04                           Page 2

                    SECTION IV - FIRE AND EXPLOSION HAZARD DATA



CLOSED CONTAINER MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT OR BURST WHEN

CONTAMINATED WITH WATER ( CO2 EVOLVED ) .



SPECIAL FIREFIGHTING PROCEDURES: DO NOT BREATHE FUMES. WEAR SELF ?CONTAINED

BREATHING APPARATUS ( PRESSURE DEMAND, MSHA/ NOISH- APPROVED OR EQUIVALENT)

AND FULL PROTECTIVE GEAR. DURING A FIRE, HEXAMETHYLENE DIISOCYANATE ( HDI )

VAPORS AND OTHER IRRITATING, HIGHLY TOXIC GASES MAY BE GENERATED BY THERMAL

DECOMPOSITION OR COMBUSTION.

                         SECTION V - HEALTH AND HAZARD DATA





EFFECTS OF OVEREXPOSURE: ACUTE INHALATION: HDI VAPORS OR MISTS AT CONCENTRATIONS ABOVE

THE TLV OR MGL CAN IRRITATE ( BURNING SENSATION) THE MUCOUS MEMBRANES IN THE RESPIRATORY

TRACT ( NOSE, THROAT, LUNGS ) . THIS CAN CAUSE RUNNY NOSE, SORE THROAT, COUGHING, CHEST

DISCOMFORT, SHORTNESS OF BREATH AND REDUCED LUNG FUNCTION ( LUNG OBSTRUCTION) . PERSONS

WITH A PREEXISTING, NONSPECIFIC BRONCHIAL HYPERACTIVITY CAN RESPONDTO CONCENTRATIONS

BELOW THE TLV OR MGL WITH SIMILAR SYMPTOMS AS WELL AS ASTHMA ATTACK.           EXPOSURE WELL

ABOVE THE TLV OR MGL MAY LEAD TO BRONCHITIS, BRONCHIAL SPASM AND PULMONARY EDEMA ( FLUID

IN THE LUNGS ) . THESE EFFECTS ARE USUALLY REVERSIBLE. CHEMICAL OR HYPERSENSITIVE PNEUMONITIS,

WITH FLU LIKE SYMPTOMS ( E. G. FEVER, CHILLS ) HAS BEEN REPORTED. SOLVENT VAPORS MAY BE

IRRITATING TO THE EYES, NOSE AND THROAT. SYMPTOMS OF IRRITATION MAY INCLUDE: REDNESS, BURNING

AND ITCHING OF THE EYES, DRYNESS OF THE THROAT AND TIGHTNESS OF THE CHEST.        OTHER POSSIBLE

SYMPTOMS OF OVEREXPOSURE INCLUDE HEADACHE, NAUSEA, NARCOSIS, FATIGUE AND LOSS OF APPETITE.

A CONCENTRATION OF 200 PPM BA CAN CAUSE EYE, NOSE AND THROAT IRRITATION.

AT 300 PPM THESE EFFECTS CAN BECOME SEVERE. PERSONS EXPOSED TO 200 PPM OF NYLENE EXPERIENCES

EYE NOSE AND THROAT IRRITATION. CONCENTRATIONS OF 10, 000 PPM OF XYLENE CAN BE IMMEDIATELY

DANGEROUS TO LIFE AND HEALTH.

CHRONIC INHALATION...AS A RESULT OF PREVIOUS REPEATED OVEREXPOSURES OR A SINGLE LARGE DOSE,

CERTAIN INDIVIDUALS WILL DEVELOP ISOCYANATE SENSITIZATION (CHEMICAL ASTHMA). THIS WILL CAUSE

THEM TO REACT TO A LATER EXPOSURE TO ISOCYANATES AT LEVELS WELL BELOW THE TLV OR MGL.

THESE SYMPTOMS WHICH INCLUDE: CHEST TIGHTNESS, WHEEZING, COUGH, SHORTNESS OF BREATHE OR

ASTHMATIC ATTACK, COULD BE IMMEDIATE OR DELAYED UP TO SEVERAL HOURS AFTER EXPOSURE.

SIMILAR TO MANY NON - SPECIFIC ASTHMATIC RESPONSES, THERE ARE REPORTS THAT ONCE SENSITIZED AN

INDIVIDUAL, CAN EXPERIENCETHESE SYMPTOMS ON EXPOSURE TO DUST, COLD AIR OR OTHER IRRITANTS.

THIS INCREASED LUNG SENSITIVITY CAN PERSIST FOR WEEKS AND IN SEVERE CASES FOR SEVERAL YEARS.

CHRONIC OVEREXPOSURE TO ISOCYANATES HAS ALSO BEEN REPORTED TO CAUSE LUNG DAMAGE,

INCLUDING DECREASE IN LUNG FUNCTION, WHICH MAY BE PERMANENT. SENSITIZATION MAY BE EITHER

TEMPORARY OR PERMANENT.         CHRONIC EXPOSURE TO ORGANIC SOLVENTS HAS BEEN ASSOCIATED WITH

VARIOUS NEUROTOXIC EFFECTS, INCLUDING PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.

SYMPTOMS INCLUDE: LOSS OF MEMORY, LOSS OF INTELLECTUAL ABILITY AND LOSS OF COORDINATION.

ACUTE SKIN CONTACT: ISOCYANATES REACT WITH SKIN PROTEIN AND MOISTURE CAN CAUSE SKIN

IRRITATION; SUCH AS REDDENING, SWELLING, RASH, SCALING OR BLISTERING. PERSONS MAY DEVELOP

SKIN SENSITIZATION. CURED MATERIAL IS DIFFICULT TO REMOVE. REPEATED OR PROLONGED SKIN

CONTACT WITH SOLVENTS CAN RESULT IN DRY DEFATTED AND CRACKED SKIN CAUSING INCREASED

SUSCEPTIBILITY TO INFECTION. IN ADDITION, SKIN IRRITATION ( I. E. REDNESS, SWELLING), WHICH









                                                                          (Continued on Page 3)

Product: M7307B                     Preparation Date : 01 / 30 / 04                  Page 4

                              SECTION VI - REACTIVITY DATA



CONDITIONS TO AVOID: AVOID HEAT, SPARKS, AND OPEN FLAME. AVOID CONTACT WITH

MOISTURE.



INCOMPATABILITY : WATER, AMINES, STRONG BASES, ALCOHOLS, METAL COMPOUNDS AND

SURFACE ACTIVE MATERIALS.



HAZARDOUS POLYMERIZATION: COULD OCCUR UNDER NORMAL CONDITIONS.



STABILITY: THIS PRODUCT IS STABLE UNDER NORMAL STORAGE CONDITIONS.



                         SECTION VII - SPILL OR LEAK PROCEDURES



STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: WARNING! ELIMINATE ALL IGNITION

SOURCES. HANDLING EQUIPMENT MUST BE GROUNDED TO PREVENT SPARKING. VENTILATE THE AREA.

WEAR APPROPRIATE PROTECTIVE CLOTHING AND RESPIRATORY PROTECTION EQUIPMENT WHEN ENTERING

THE SPILL AREA. LARGE SPILLS: KEEP SPECTATORS AWAY. FLOOR MAY BE SLIPPERY: USE CARE TO AVOID

FALLING. DIKE AND CONTAIN SPILL WITH INERT MATERIAL ( E. G SAND, EARTH ). SMALL SPILLS: TAKE UP

WITH AN ABSORBENT MATERIAL AND SEAL TIGHTLY FOR PROPER DISPOSAL. POUR DECONTAMINATION

SOLUTION OVER SPILL AREA AND ALLOW TO REACT FOR AT LEAST 10 MINUTES. COLLECT MATERIAL IN

OPEN CONTAINERS AND FURTHER AMOUNTS OF DECONTAMINATION SOLUTION. REMOVE CONTAINERS TO A

SAFE PLACE, COVER LOOSELY, AND ALLOW TO STAND FOR 24 TO 48 HOURS. WASH DOWN SPILL AREA WITH

DECONTAMINATIONS SOLUTIONS. DECONTAMINATION SOLUTIONS:

 # 1) - NON IONIC SURFACTANT UNION CARBIDE TERGITOL TMN ?10 ( 20 ) AND WATER ( 80%.

 # 2) - CONCENTRATED AMMONIA ( 3 - 8 % ) , DETERGENT ( 2 % ) , AND WATER ( 90 ?95 %) .



WASTE DISPOSAL METHOD: DISPOSE OF PRODUCT IN ACCORDANCE WITH LOCAL, COUNTY, STATE AND

FEDERAL REGULATIONS. INCINERATION IS THE PREFEERED METHOD. PLACE CONTAMINATED MATERIAL IN

SUITABLE CONTAINERS FOR DISPOSAL. PLACE IN A DISPOSAL FACILITY APPROVED UNDER RCRA

REGULATIONS FOR HAZARDOUS WASTE. USE NON ?LEAKING CONTAINERS, SEAL TIGHTLY AND LABEL

PROPERLY. EMPTY CONTAINERS MUST BE HANDLED WITH CARE DUE TO THE PRODUCT RESIDUE AND THE

FLAMMABLE SOLVENT VAPOR. DECONTAMINATE CONTAINERS PRIOR TO DISPOSAL. DO NOT HEAT OR CUT

EMPTY CONTAINERS WITH ELECTRIC OR GAS TORCH.



                  SECTION V I I I - SAFE HANDLING AND USE INFORMATION





RESPIRATORY PROTECTION: A RESPIRATOR THAT IS RECOMMENDED OR APPROVED FOR USE IN ISOCYANATE

CONTAINING ENVIORNMENTS ( AIR PURIFYING OR FRESH AIR SUPPLIED ) MAY BE NECESSARY. CONSIDER

THE TYPE OF APPLICATION AND ENVIORNMENTAL CONCENTRATIONS. OBSERVE OSHA REGULATIONS FOR

RESPIRATOR USE ( 29 CPR 1910, 134 ) . IN SPRAY APPLICATIONS, WHEN THE AIRBORNE ISOCYANATE

MONOMER CONCENTRATIONS ARE KNOWN TO BE BELOW 0.2 PPM AND IF THE POLYISOCYANATE (

POLYMERIX, OLIGOMER ) CONCENTRATIONS ARE KNOWN TO BE BELOW 10 MG/ M3, A PROPERLY FITTED AIR

PURIFYING ( ORGANIC VAPOR/ PARTICULATE) RESPIRATOR, PROVEN BY TEST TO BE EFFECTIVE IN

ISOCYANATE CONTAINING SPRAY PAINT ENVIORNMENTS, WILL PROVIDE SUFFICIENT PROTECTION. WHEN

THE AIRBORNE ISOCYANATE CONCENTRATIONS AIR NOT KNOWN, OR IF EITHER OF THE ABOVE GUIDELINES

IS EXCEEDED, OR IF SPRAYING IS PERFORMED IN A CONFINED SPACE OR

                                                                       ( CONTINUED ON PAGE 5 )

                                           MATERIAL           SAFETY          DATA      SHEET



              SECTION I              -     CHEMICAL PRODUCT AND COMPANY IDENTIFICATION



    PRODUCT NAME         : CH LOCK UV GL PART FROG SHEILD

    IDENTIFICATION NUMBER: CLUVGL                       DATE PRINTED: 10/07/04

    PRODUCT USE/ CLASS    :



    SUPPLIER:                                                                   MANUFACTURER:

     FAR FROM NORMAL                                                             T. J. RONAN PAINT CORPORATION

     1318 39TH ST NW                                                                 749 EAST 135TH ST.

     FARGO, ND 58102                                                                 BRONX, NY 10454



    CHEMTREC: (800) 424-9300                                                    CHEMTREC: ( 800 ) 424-9300

    24 HOUR EMERGENCY HOTLINE                                                   24 HOUR EMERGENCY HOTLINE



    PREPARER: JD, PHONE: 718-292-1100, PREPARE DATE: 10/07/04



                           SECTION II - COMPOSITION/ INFORMATION ON INGREDIENTS



                                                              WT. PERCENT -----------------OCCUPATIONAL EXPOSURE LIMITS-----

--------CHEMICAL NAME--------------------- CAS NUMBER     IS LESS THAN TLV-TWA           TLV- STEL   PEL- TWA   PEL-CEILING    SKIN









                                                               45. 0 %      110 ppm       150 ppm                                No

POLYACRYLATE RESIN IN WATER                  N/A

                                             111-76-2            5.0%         25 ppm        50 ppm       50 ppm      N. E.       No

ETHYLENEGLYCOL MONOBUTYL ETHER

                                             64742-95-6          5.0%        No Info       No Info                               No

PETROLEUM DISTILLATE

                                             95-63-6             5.0%         N. E.         N. E.          N. E.      N. E.      No

1,2,4 ?TRIMETHYLBENZENE



(See Section 11 for abbreviation legend)

                                              SECTION III - PHYSICAL DATA



BOILING RANGE                     : 212 - 350 F                          VAPOR DENSTIY    : Is heavier than air

ODOR                              : LOW                                  SPECIFIC GRAVITY : 1. 0555

APPEARANCE                        : CLEAR LIQUID                         EVAPORATION RATE : Is slower than Ether

SOLUBILITY IN H20                 : YES

VOLATILE BY WEIGHT               : 58. 3 %                               VOLATILE BY VOL :           62.4%

VOCS, ILS/ GAL                   :  1. 57                                VOCS, GRAMS/ LTR :          188



( See Section XI for abbreviation legend )

                                SECTION IV - FIRE AND EXPLOSION HAZARD DATA

FLASH POINT : 106 F                                                      LOWER EXPLOSIVE LIMIT: 1.0%

( TAGLIABUE CLOSED CUP)                                                  UPPER EXPLOSIVE LIMIT: 10.6%



EXTINGUISHING MEDIA : CO2 DRY CHEMICAL FOAM WATER FOG

UNUSUAL FIRE AND EXPLOSIVE HAZARDS: KEEP CONTAINER CLOSED TIGHTLY.

ISOLATE FROM HEAT, SPARKS AND OPEN FLAME. CLOSED CONTAINERS MAY EXPLODE.



                                                                                Preparation Date : 10/ 07/ 04

            SECTION IV - FIRE AND EXPLOSION HAZARD DATA



WHEN EXPOSED TO EXTREME HEAT.



SPECIAL FIREFIGHTING PROCEDURES: WEAR SELF CONTAINED BREATHING APPARATUS.

WATER MAY SPREAD FIRE. WATER SPRAY SHOULD BE USED TO COOL CONTAINERS

EXPOSED TO FIRE.



                  SECTION V- HEALTH HAZARD DATA



EFFECTS OF OVEREXPOSURE: INHALATION: NAUSEA, DIZZINESS, HEADACHE, VOMITING.

SKIN CONTACT: REPEATED CONTACT MAY CAUSE IRRITATION, AND DERMATITIS. EYE

CONTACT : CAUSES IRRITATION, REDNESS, TEARING, BLURRED VISION. INGESTION: CAN

CAUSE IRRITATION OF THE DIGESTIVE TRACT, NAUSEA, VOMITING AND DIARRHEA. IN SEVERE

CASES INGESTION CAN BE FATAL. ASPIRATION INTO LUNGS CAN CAUSE CHEMICAL

PNEUMONITIS WHICH CAN BE FATAL. REPORTS HAVE ASSOCIATED REPEATED AND PROLONGED

OCCUPATIONAL OVEREXPOSURE TO SOLVENTS WITH PERMANENT BRAIN AND NERVOUS

SYSTEM DAMAGE. INTENTIONAL MISUSE BY DELIBERATELY CONCENTRATING AND INHALING

THIS PRODUCT MAY BE HARMFUL OR FATAL.



MEDICAL CONDITIONS PRONE TO AGGRAVATION: PRE EXISTING EYE, SKIN OR RESPIRATORY

DISORDERS.



EMERGENCY AND FIRST AID PROCEDURES: EYE CONTACT : FLUSH WITH LARGE QUANTITIES

OF WATER FOR 15 MINUTES. IF IRRITATION PERSISTS GET MEDICAL ATTENTION. SKIN

CONTACT: REMOVE SATURATED CLOTHING. WASH WITH SOAP AND WATER. SEEK MEDICAL

ATTENTION IF IRRITATION DEVELOPS. LAUNDER SATURATED CLOTHING AND CLEAN SHOES

BEFORE REUSE. INHALATION: REMOVE TO FRESH AIR. GIVE ARTIFICIAL RESPIRATION IF

NECESSARY. GET MEDICAL ATTENTION. INGESTION: DO NOT INDUCE VOMITING. IF VOMITING

OCCURS SPONTANEOUSLY KEEP HEAD BELOW HIPS TO PREVENT INHALATION. SEEK MEDICAL

ATTENTION IMMEDIATELY.



PRIMARY ROUTE (S) OF ENTRY: SKIN CONTACT   INHALATION   INGESTION





                      SECTION VI - REACTIVITY DATA





HAZARDOUS DECOMPOSTION PRODUCTS: MAY PRODUCE TOXIC FUMES WHEN HEATED TO

DECOMPOSITION. FUMES MAY CONTAIN CARBON MONOXIDE AND/ OR CARBON DIOXIDE.

CONDITIONS TO AVOID: AVOID HEAT, SPARKS, AND OPEN FLAME.

INCOMPATABILITY: ISOLATE FROM OXIDIZERS, HEAT SPARKS AND OPEN FLAME.

HAZARDOUS POLYMERIZATION: WILL NOT OCCUR UNDER NORMAL CONDITIONS.

STABILITY: THIS PRODUCT IS STABLE UNDER NORMAL STORAGE CONDITIONS.









                 SECTION VII - SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: REMOVE ALL SOURCES OF

IGNITION. COVER WITH INERT ABSORBENT MATERIAL.



WASTE DISPOSAL METHOD: DISPOSE OF PRODUCT IN ACCORDANCE WITH LOCAL, COUNTY,

STATE AND FEDERAL REGULATIONS.





                 SECTION VIII - SAFE HANDLING AND USE INFORMATION



RESPIRATORY PROTECTION: WEAR TO AVOID BREATHING SPRAY MIST, HEATED VAPORS

OR FUMES OR IF EXPOSURE MAY OR DOES EXCEED OCCUPATIONAL EXPOSURE LIMITS

(SECTION II). USE A NIOSH- APPROVED RESPIRATOR TO PREVENT OVEREXPOSURE.



VENTILATION: USE EXPLOSION PROOF VENTILATION AS REQUIRED TO CONTROL VAPOR

CONCENTRATIONS.



PROTECTIVE GLOVES: WEAR IMPERVIOUS GLOVES.



EYE PROTECTION: WEAR CHEMICAL RESISTANT GOGGLES TO PREVENT EYE CONTACT.



OTHER PROTECTIVE EQUIPMENT: WEAR PROTECTIVE CLOTHING AS REQUIRED PREVENTING

SKIN CONTACT.



HYGIENIC PRACTICES: WASH WITH SOAP AND WATER AFTER HANDLING AND BEFORE EATING,

DRINKING, SMOKING OR USING TOLIET FACILITIES. LAUNDER CONTAMINATED CLOTHING

BEFORE REUSE.



                 SECTION IX - SPECIAL PRECAUTIONS



PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: KEEP AWAY FROM HEAT, SPARKS

AND OPEN FLAME. KEEP CONTAINERS TIGHTLY CLOSED. STORE AWAY FROM STRON OXIDIZING

AGENTS IN A COOL, DRY PLACE WITH ADEQUATE EXPLOSION - PROOF VENTILATION. AVOID

CONTACT WITH EYES SKIN AND CLOTHING.



OTHER PRECAUTIONS: DO NOT WELD, HEAT OR DRILL ON OR NEAR CONTAINER; EVEN EMPTIED

CONTAINERS CAN CONTAIN EXPLOSIVE VAPORS. UNIFORMS OR CLOTHING CONTAINING PAINT

RESIDUE SHOULD NOT BE LAUNDERED WITH HOUSEHOLD GARMENTS.

DO NOT TAKE INTERNALLY. OBSERVE LABEL PRECAUTIONS.





                            SECTION X - HMIS RATINGS





HMIS RATINGS - HEALTH : 3    FLAMMABILITY:   3      REACTIVITY : 0

PRODUCT: CLUVGL                                            Preparation Date : 10/07/04

                                     SECTION XI - OTHER REGULATIONS







SARA SECTION 313 :



THIS PRODUCT CONTAINS THE FOLLOWING SUBSTANCES SUBJECT TO THE REPORTING

REQUIREMENTS OF SECTION 313 OF TITLE III OF THE SUPERFUND AMENDMENTS AND

REAUTHORIZATION ACT OF 1986 AND 40 CFR PART 372 :





------------ CHEMICAL NAME ---------------      CAS NUMBER       WT/ WT % IS LESS THAN

ETHYLENEGLYCOL MONOBUTYL ETHER                      111-76-2                   5.0%

1, 2, 4 ?TRIMETHYLBENZENE                          95-63-6                    5.0%



PREVIOUS MSDS REVISION DATE :          10/ 07/ 04



LEGEND :    N. A. - NOT APPLICABLE, N. E. - NOT ESTABLISHED

            N. D. - NOT DETERMINED









 The information contained on this MSDS is to the best of our knowledge and belief, accurate. However,

since the conditions of handling and use are beyond our control, we make no guarantee of results, and

assume no liability for damages incurred by use of this material. It is the responsibility of the user to

comply with all applicable federal, state and local laws and regulations.





< END OF MSDS >