801833PM Page 1 of 7
09-09-2008
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
REVISION DATE: 08-19-2008 12-10-2007
SUPERSEDES:
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
COMPANY INFORMATION
Specialty Construction Brands, Inc.
An H.B. Fuller Company
1105 S. Frontenac Street
Aurora, IL 60504
Phone: 1-800-323-7407
Medical Emergency Phone Number (24 Hours): 1-888-853-1758
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
PRODUCT INFORMATION
PRODUCT IDENTIFIER: 801833PM
PRODUCT NUMBER: CP0761
PRODUCT NAME: CHILDERS CP-76-1
PRODUCT DESCRIPTION: Sealant
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
Unlisted ingredients are not 'hazardous' per the Occupational Safety and Health Administration Hazard
Communication Standard (29 CFR 1910.1200) and/or are not found on the Canadian Workplace Hazardous
Materials Information System ingredient disclosure list. See Section 8 for any additional exposure limit guidelines.
Chemical Name CAS # PERCENT OSHA PEL
Aluminum silicate of potash and soda. 68476-25-5 30 - 50 TWA (as Al) (Total dust) 15 MG/M3
TWA (as Al) (Respirable dust) 5 MG/M3
Stoddard solvent 8052-41-3 10 - 30 TWA 100 ppm
Crystalline silica 14808-60-7 10 - 30 TWA (Respirable dust) 0.1 MG/M3
Mica 12001-26-2 1-5 TWA (Respirable dust) 3 MG/M3
Toluene 108-88-3 1-5 TWA 100 ppm
STEL 150 ppm
Aromatic petroleum distillate 64742-95-6 1-5 Not established
Trimethylbenzene, 1,3,5 108-67-8 1-5 Not established
Trimethylbenzene, 1,2,4- 95-63-6 1-5 Not established
Xylene 1330-20-7 0.1 - 1 TWA 100 ppm
801833PM Page 2 of 7
09-09-2008
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
STEL 150 ppm
Ethylbenzene 100-41-4 0.1 - 1 TWA 100 ppm
STEL 125 ppm
Titanium dioxide 13463-67-7 0.1 - 1 TWA (Total dust) 10 MG/M3
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Combustible
Moderate eye irritant.
Can cause skin irritation.
Harmful if swallowed.
Cancer hazard.
HMIS RATING: HEALTH -- 2 FLAMMABILITY -- 2 REACTIVITY -- 0
See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective equipment
recommendations.
POTENTIAL HEALTH EFFECTS BY ROUTE OF ENTRY
EYE: Can cause moderate irritation, tearing and reddening, but not likely to permanently injure eye tissue.
SKIN: Can cause skin irritation.
Component(s) may be absorbed through intact skin, but it is unlikely that harmful effects will occur unless contact is
prolonged, repeated, and extensive.
INHALATION: Can cause minor respiratory irritation. Inhalation of dusts produced during cutting, grinding or
sanding of this product may cause irritation of the respiratory tract.
Inhalation of high concentrations may result in central nervous system (CNS) effects such as dizziness, weakness,
fatigue, nausea, headache, and lack of coordination. Overexposure to crystalline silica may cause silicosis.
This product contains one or more materials that may be hazardous when present as an airborne dust. During normal
handling of the product, the material is encapsulated within the product and will not present an exposure risk. Once
the product has reached its final state and is abraded or disturbed, dusting and exposure may occur.
INGESTION: Ingestion is not an anticipated route of exposure. Harmful if swallowed. Irritating to mouth, throat,
and stomach.
LONG-TERM (CHRONIC) HEALTH EFFECTS
REPRODUCTIVE: Contains a substance that is a probable reproductive hazard based on human
studies.
TARGET ORGAN(S): Kidneys Central nervous system Lungs Reproductive system Liver Blood
REGULATED CARCINOGEN STATUS:
Unless noted below, this product does not contain regulated levels of NTP, IARC, ACGIH, or OSHA listed
carcinogens.
Crystalline silica
Ethylbenzene
Titanium dioxide
EXISTING HEALTH CONDITIONS AFFECTED BY EXPOSURE: Kidney disease; Lung disease; Liver disease;
Blood disorders (like anemia)
801833PM Page 3 of 7
09-09-2008
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
SECTION 4: FIRST AID MEASURES
IF IN EYES: Flush eyes with plenty of water for at least 20 minutes retracting eyelids often. Tilt the head to prevent
chemical from transferring to the uncontaminated eye. Get immediate medical attention.
IF ON SKIN: Wash with soap and water. Get medical attention if irritation develops or persists.
IF VAPORS INHALED: Remove to fresh air. Call a physician if symptoms persist.
IF SWALLOWED: Do not induce vomiting. Seek medical attention immediately. Drink two glasses of water or
milk to dilute. Do not give anything by mouth to an unconscious person.
SECTION 5: FIRE FIGHTING MEASURES
FLASH POINT: 40C; 104F
AUTOIGNITION TEMPERATURE: Not established
LOWER EXPLOSIVE LIMIT (% in air): Not established
UPPER EXPLOSIVE LIMIT (% in air): Not established
EXTINGUISHING MEDIA: Use water spray, foam, dry chemical or carbon dioxide.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Vapors are heavier than air and can travel to a source of ignition
and flash back.
SPECIAL FIRE FIGHTING INSTRUCTIONS: Persons exposed to products of combustion should wear self-
contained breathing apparatus and full protective equipment.
HAZARDOUS COMBUSTION PRODUCTS: Carbon dioxide, Carbon monoxide
SECTION 6: ACCIDENTAL RELEASE MEASURES
SPECIAL PROTECTION: Exposure to the spilled material may be irritating or harmful. Follow
personal protective equipment recommendations found in Section 8 of this
MSDS. Additional precautions may be necessary based on special
circumstances created by the spill including; the material spilled, the quantity
of the spill, the area in which the spill occurred. Evaporation of volatile
substances can lead to the displacement of air creating an environment that
can cause asphyxiation.
CLEAN-UP: Dike if necessary, contain spill with inert absorbent and transfer to containers
for disposal. Keep spilled product out of sewers, watersheds, or water
systems.
Avoid creating dusts. Cover material with absorbent and moisten and collect
for disposal.
Shut off ignition sources; including electrical equipment and flames. Do not
allow smoking in the area.
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
SECTION 7: HANDLING AND STORAGE
Handling: Harmful or irritating material. Avoid contacting and avoid breathing the material. Use only in
a well ventilated area. Avoid breathing material.
Keep away from heat, sparks and flame.
Wash thoroughly after handling.
Keep container closed.
Emptied container retains vapor and product residue.
Observe all labeled precautions until container is cleaned.
Drums of this material should be grounded when pouring.
DO NOT CUT OR WELD ON OR NEAR THIS CONTAINER.
Storage: Store in a cool, dry, ventilated location. Keep away from heat and flame. Keep container
closed.
Consult the Technical Data Sheet for specific storage instructions.
801833PM Page 4 of 7
09-09-2008
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
EYE PROTECTION: Wear safety glasses with side shields when handling this product.
Wear additional eye protection such as chemical splash goggles
and/or face shield when the possibility exists for eye contact with
splashing or spraying liquid, or airborne material. Have an eye wash
station available.
SKIN PROTECTION: Avoid skin contact by wearing chemically resistant gloves. Skin
absorption may potentially contribute to the overall exposure to this
material. Appropriate measures should be taken to prevent
absorption so that the TLV is not invalidated.
GLOVES: Nitrile
RESPIRATORY PROTECTION: Respiratory protection may be required to avoid overexposure when
handling this product. Use a respirator if general room ventilation is
not available or sufficient to eliminate symptoms. NIOSH approved
air purifying respirator with organic vapor cartridge.
Respirators should be selected by and used following requirements
found in OSHA's respirator standard (29 CFR 1910.134).
VENTILATION: Use local exhaust ventilation or other engineering controls to
minimize exposures.
EXPOSURE LIMITS:
Chemical Name ACGIH EXPOSURE LIMITS AIHA WEEL
Aluminum silicate of potash and TWA (as Al) (Total dust) 10 MG/M3 Not established
soda.
Stoddard solvent TWA 100 ppm Not established
Crystalline silica TWA (Respirable dust) 0.025 MG/M3 Not established
Mica TWA (Respirable dust) 3 MG/M3 Not established
Toluene TWA 20 ppm Not established
Aromatic petroleum distillate Not established Not established
Trimethylbenzene, 1,3,5 Not established Not established
Trimethylbenzene, 1,2,4- Not established Not established
Xylene TWA 100 ppm Not established
STEL 150 ppm
801833PM Page 5 of 7
09-09-2008
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
Ethylbenzene TWA 100 ppm Not established
STEL 125 ppm
Titanium dioxide TWA 10 MG/M3 Not established
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Solid
COLOR: Gray
ODOR: Solvent
ODOR THRESHOLD: Not established
WEIGHT PER GALLON (lbs.): 10.5
SPECIFIC GRAVITY: 1.2
SOLIDS (% by weight): 71.7
Not applicable
pH: Not established
BOILING POINT (deg. C): Not established
FREEZING/MELTING POINT (deg. C): Not established
VAPOR PRESSURE (mm Hg): Not established
VAPOR DENSITY: Not established
EVAPORATION RATE: Not established
OCTANOL/WATER COEFFICIENT: Not established
SECTION 10: STABILITY AND REACTIVITY
STABILITY: Stable under normal conditions.
CHEMICAL INCOMPATIBILITY: Strong oxidizing agents
HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide
SECTION 11: TOXICOLOGICAL INFORMATION
CHEMICAL NAME LD50/LC50
Aluminum silicate of potash and soda. Not established
Stoddard solvent Not established
Crystalline silica Not established
Mica Not established
Toluene Oral LD50 Rat = 636 mg/kg
Inhalation LC50 Rat = 49000 mg/cu m/4H
Dermal LD50 Rabbit = 14.1 ml/kg
Aromatic petroleum distillate Oral LD50 Rat = 8400 mg/kg
Trimethylbenzene, 1,3,5
Inhalation LC50 Rat = 24000 mg/cu m/4H
Trimethylbenzene, 1,2,4- Oral LD50 Rat = 5 g/kg
Inhalation LC50 Rat = 18000 mg/cu m/4H
801833PM Page 6 of 7
09-09-2008
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
Xylene Oral LD50 Rat = 4300 mg/kg
Inhalation LC50 Rat = 5000 ppm/4H
Dermal LD50 Rat = 1700 mg/kg
Ethylbenzene Oral LD50 Rat = 3500 mg/kg
Dermal LD50 Rabbit = 17.8 ml/kg
Titanium dioxide Not established
TOXICOLOGY SUMMARY: No additional health information available.
SECTION 12: ECOLOGICAL INFORMATION
OVERVIEW: No ecological information available
356 g VOC/liter of material, less water and exempt solvents
(VOC theoretically determined using EPA Reference method 24)
SECTION 13: DISPOSAL CONSIDERATIONS
This product meets the definition of hazardous waste under the U.S. EPA Hazardous Waste Regulations 40 CFR
261. It is ignitable waste class D001. Disposal via incineration is recommended. Consult your state, local, or
provincial authorities for more restrictive requirements.
LAND DISPOSAL RESTRICTIONS: Toluene Xylenes (o-, m-, p- isomers) Ethyl benzene
SECTION 14: TRANSPORTATION INFORMATION
Consult Bill of Lading for transportation information.
DOT: NOT REGULATED
IATA: NOT REGULATED
SECTION 15: REGULATORY INFORMATION
INVENTORY STATUS
U.S. EPA TSCA: This product is in compliance with the Toxic Substances Control Act's
Inventory requirements.
CANADIAN CEPA DSL: This product is in compliance with the Canadian Domestic Substance List
requirements.
EUROPEAN EINECS: This product is in compliance with the European Inventory of Notified and
Existing Chemical Substances requirements.
AUSTRALIA AICS: This product is in compliance with the Australian Inventory of Chemical
Substances requirements.
If you need more information about the inventory status of this product call 651-236-5858.
This product may contain chemical substances that are regulated for export by various government agencies (such as
the Environmental Protection Agency, the Bureau of Industry and Security, or the Drug Enforcement
Administration, among others). Before exporting this product from the USA or Canada, we recommend you contact
us at 651-236-5858 (USA) or 450-655-1306 x227 (Canada) to request an export review.
FEDERAL REPORTING
EPA SARA Title III Section 313
Unless listed below, this product does not contain toxic chemical(s) subject to the reporting requirements of section
313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR part 372. EPA
has advised that when a percentage range is listed the midpoint may be used to fulfill reporting obligations.
Chemical Name CAS# %
Toluene 108-88-3 1-5
801833PM Page 7 of 7
09-09-2008
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
1,2,4-Trimethylbenzene 95-63-6 1-5
Xylene (mixed isomers) 1330-20-7 0.1 - 1
ethylbenzene 100-41-4 0.1 - 1
WHMIS STATUS: Unless listed below, this product is not controlled under the Canadian Workplace Hazardous
Materials Information System.
B3
D2B D2A
STATE REPORTING
This MSDS is not prepared for distribution in California.
SECTION 16: ADDITIONAL INFORMATION
This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health
Administration (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the Canadian Workplace
Hazardous Materials Information System (WHMIS).
Prepared by: The Global Regulatory Department
Phone: 651-236-5842
The information and recommendations set forth herein are believed to be accurate. Because some of the information
is derived from information provided to Specialty Construction Brands, Inc. from its suppliers, and because
Specialty Construction Brands, Inc. has no control over the conditions of handling and use, Specialty Construction
Brands, Inc. makes no warranty, expressed or implied, regarding the accuracy of the data or the results to be
obtained from the use thereof. The information is supplied solely for your information and consideration, and
Specialty Construction Brands, Inc. assumes no responsibility for use or reliance thereon. It is the responsibility of
the user of Specialty Construction Brands, Inc. products to comply with all applicable federal, state and local laws
and regulations.
|