Material Safety Data Sheet
Reviewed 1/01
Revised 9/97
Section I
Manufacturer's Name: Emergency Response #
Coatings For Industry, Inc. 1-800-535-5053
319 Township Line Road
Souderton, PA 18964 Non-Emergency #
215-723-0919
Trade Name:
Urethabond 3060 Formula:
Black Proprietary
Section II - Hazardous Ingredients
% ACGIH/TLV OSHA/PEL CAS#
---------------------------------------------------------------------------------------------------------
2-Pyrrolidinone, 1-Methyl 6.05 N.E. N.E. 872-50-4
(100 ppm recommended by mfg.)
---------------------------------------------------------------------------------------------------------
3.5 mg/M3 3.5 mg/M3 1333-86-4
Carbon Black Pigment 3.25
---------------------------------------------------------------------------------------------------------
2-Butoxyethanol 0.6 111-76-2
---------------------------------------------------------------------------------------------------------
Propylene Glycol 0.6 57-55-6
N.E. = Not Established
Section III - Physical Data
Weight per Gallon ~~~~~~~~~~~~~~~~~~~~~~~~ 8.86 lb./gal.
% Volatile by Weight ~~~~~~~~~~~~~~~~~~~~~~ 59.76%
Vapor Density ~~~~~~~~~~~~~~~~~~~~~~~~~~~ Heavier than air
Liquid Density~~~~~~~~~~~~~~~~~~~~~~~~~~~ Heavier than water
Solubility in Water ~~~~~~~~~~~~~~~~~~~~~~~~ Soluble - Water base
Appearance ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Black
Section IV - Fire and Explosion Hazard Data
Flammability Class: IIIB Flash Point: None LEL: None UEL: None
-EXTINGUISHING MEDIA: Water for dried polymer
-SPECIAL FIREFIGHTING PROCEDURES: Wear full body protective clothing and
MESA/NOISH approved self contained breathing apparatus. Use water to cool fire
exposed containers.
-UNUSUAL FIRE AND EXPLOSION HAZARDS: None known.
Unusual Fire and Explosion Hazards - Material will not sustain combustion but closed
containers may explode due to build up of steam pressure when exposed to heat.
U-3060, Page 2 of 3
Section V - Health Hazard Data
Threshold Limit Values - See section II
Effects of Overexposure
Excessive inhalation causes dizziness, headache and nausea.
Severe eye irritation due to eye contact, contact with skin may cause drying.
Emergency and First Aid Procedures for Overexposure
Eye Contact - Flush with water.
Skin Contact - Wash with mild soap and water and apply skin cream.
Inhalation - Remove to fresh air and call physician, apply artificial respiration if
necessary.
Section VI - Reactivity Data
Stability ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Stable
Incompatibility (materials to avoid) ~~~~~~~~~~~~~~~~~ Will not occur
Hazardous Decomposition Products ~~~~~~~~~~~~~~~~~ Will not occur
Hazardous Polymerization ~~~~~~~~~~~~~~~~~~~~~~~~ Will not occur
Section VII - Spill or Leak Procedures
Steps to be Taken in Case Material is Released or Spilled - Avoid breathing vapors.
Ventilate area. Remove with inert absorbent.
Waste Disposal Method - Dispose of in accordance with local, state, and federal
regulations. Incinerate in approved facility. Do not incinerate in closed container.
Section VIII - Special Precaution Information
Respiratory Protection -
In restricted ventilation areas, use Bureau of Mines approved chemical-mechanical filters
designed to remove gas and vapor. In confined areas, use Bureau of Mines air line type
respirator or hood.
Ventilation -
Provide general dilution or local exhaust ventilation in volume and pattern to keep TLV
of hazardous ingredients below acceptable and stated limits.
Protective Gloves -
Required - polyethylene lined recommended.
Eye Protection -
Use safety eye wear to protect against splashed liquid.
Other Protective Equipment -
Protective overalls will prevent clothing contamination and skin irritation.
U-3060, Page 3 of 3
Section IX - Special Precautions
Precautions to be Taken in Handling and Storage -
Do not store above 120?F.
Do not take internally.
Keep from freezing.
Do not leave containers open.
Avoid repeated or prolonged contact with skin.
Section X - Additional Regulatory Information
SARA Title III section 313
This product contains the following toxic chemicals subject to the reporting requirements
of section 313 of the Emergency Planning and Community Right to Know Act of 1986
and of 40 CFR 372:
CAS# 872-50-4 2-Pyrrolidinone, 1-Methyl 6.05% by weight
-------------------------------------------------------------------------------------------------------
NOTICE : This information is presented in good faith and believed to be accurate as of
the effective date below. However, no warranty is express or implied regarding the
accuracy of this data or the results to be obtained from the use thereof. Coatings For
Industry, Inc. assumes no responsibility for personal injury or property damage to
vendees, users, or third parties caused by the material, such vendees or users assume all
risks associated with the use of the material. Regulatory requirements are subject to
change and may differ from one location to another; it is the buyer's responsibility to
ensure that its activities comply with federal, state or provincial, and local laws. The
preceding specific information is made for the purpose of complying with numerous
federal, state or provincial, and local laws and regulations.
7/95
|