Technical Data Sheet



BILO Floor Wax No. 303

                       For wood, cork and open-pored stone floors after pre-treatment with LIVOS oils. Not

Range of application

                       suitable for moist areas.



                       Silky gloss, elastic, anti-static finish.

Technical qualities



                       Linseed oil, beeswax, carnauba wax, orange oil, Isoaliphates and Dammar resin.

Full declaration



                       Clear.

Color



                       Apply with brush, cotton cloth, spatula or polishing machine.

Application method



                       1 liter (1.06 fl. quart.) is sufficient for 75-95 m2 (807 � 1022 ft²) per coat, i.e. 12 ml/m².

Coverage

                       Coverage could be considerably less depending on the condition and absorbency of the

                       surface. Always do a test application!



                       At 23oC (73°F) and 50 % relative humidity, 24 - 48 hours. Do not walk on floors until

Drying Time

                       completely dry.



                       Approximately 0.85 g/ml.

Specific gravity

                       Always be sure to store and dispose cleaning cloths, polishing pads, sponges, etc. that are

Safety advice

                       still wet or even slightly moist with BILO Floor Wax No. 303 in an airtight metal container

                       or in water, as there is a danger of spontaneous combustion caused by the linseed oil in the

                       product.



                       The product alone will not undergo spontaneous combustion.

                       Contains Limonene

                       S2     Keep out of the reach of children

                       S 62   If swallowed, do not induce vomiting: seek medical advice immediately and show

                              this container or label



                       According to locally regulated laws.

Disposal



                       0.2 lt; 0.375 lt; 2.5 lt.

Container Sizes



                       Cool and dry please see label for expiry date. Please, smooth the surface after use, close lid

Storage

                       tightly and use within 3 months.



                       See reverse for Application Instructions.









LIVOS Plantchemistry D - 29568 Wieren · Tel. +49 58 25 / 88 - 0 · Fax 88 60 · www.livos.de · info@livos.de

How to use



BILO Floor Wax No. 303



                            The surface must be saturated with a LIVOS oil product.

Preparation



                            Pre-treatment has to be completely dry. After a minimum of 24 - 48 hours, apply a very thin

Application

                            coat of BILO Floor Wax with a cloth, wax brush or spatula (for hot wax application, use No.

                            307).

                            Warning: Applying too thickly can cause surface to be sticky and difficult to polish. Any

                            puddles of wax will develop a whitish film upon drying; using a short-haired, medium-hard

                            brush, for example, helps to avoid such problems.

                            Polishing of treated wood floors must be done with strong force in the direction of the

                            grain after 24h at the earliest, with a wadded cloth, a polishing brush, a heavy duty manual

                            polisher, or electric floor polisher. An even, silky gloss finish should develop that, after the

                            dissipation of frictional heat, should not be sticky to the touch. On the next day, after

                            further drying, polish again. Repeated polishing in subsequent weeks will make the floor

                            more and more wear-resistant.



                            During the first 3 weeks after application treat newly waxed surfaces with great care. For

Important tips

                            short, limited usage, cover surface with corrugated cardboard or another diffuse-able

                            material.

                            Rugs or carpets are not yet to be laid permanently on treated surfaces, and under no

                            circumstances should the surface be washed with water during the drying time. Sand,

                            moisture and dirt do the biggest damage to the floor before drying is complete.

                            Simplifying of the wax application is possible through warming in a water bath, but

                            PLEASE NOTE that the product will become inflammable through this process.



                            Remove dust with vacuum cleaner or mop.

Care

                            Rubber scuffs and other heavy soiling can be removed with SVALOS Thinner No. 222.

                            Depending upon the degree of use of the surface, re-treat the surface 1 - 2 times a year

                            with GLEIVO Beeswax No. 315 or BIVOS Oil Wax No. 375. Clean surface with TRENA pH-

                            Neutral Cleaner No. 556 as needed.



                            Thoroughly clean heavily worn, soiled, or otherwise damaged areas with LATIS Natural

Renovation

                            Intensive Cleaner No. 551 or TRENA pH-Neutral Cleaner No. 556, sand and re-oil if

                            necessary, then re-wax with a thin coat of BILO Floor Wax No. 303 or SOGO Universal

                            Hard Wax No. 307 and polish.









These directions are the result of long years of research and practical testing. They are backed by our most current expert

information. New findings may invalidate this information. This data sheet is meant to serve as information and instruction.

No legal liability should be interpreted from it. In case of doubt, please contact the retailer, wholesaler, or manufacturer.



November 2006