(MSDS)MATERIAL SAFETY DATA SHEET ---VanHearron Inc. SOLO SEAL
Revision Date: 10-01-2006
SECTION I. IDENTIFICATION
PRODUCT NAME: VANHEARRON SOLO SEAL WATER REPELLENT
CHEMICAL NAME & SYNONYMS: Water-Based Mixture of Modified Silane / Water Repellent
PROCESSORS NAME: VanHearron, Inc. Greenwood, AR 72936 PH: (479) 650-2490
CAS #: Not Issued CHEMICAL FAMILY: Water-based Solution of Modified Silane
SECTION 2: COMPONENTS
INGREDIENTS CAS NUMBER % BY WT*
- Dimethyl, methylhydrogen silane 68037-59-2 5-7
-Octyltriethoxysilane 2943-75-1 5-7
- Polyethylene oxide lauryl ether 9002-92-0 0.5-1
- Water Balance
Per California South Coast Air Quality Management District (SCAQMD) RULE 443.1, this product has volatile solvents
content (VOC) of less than 50 grams/L - VOC Compliant.
SECTION 3: HEATH HAZARDS
NFPA 704 CODES: 0=Minimal, 1=Slight, 2=Moderate, 3=Serious and 4=Severe
HEALTH (BLUE) FLAMMABILITY (RED) REACTIVITY (YELLOW) CLOTHING
NFPA: 2 NFPA: 1 NFPA: 1 NFPA:
HMIS: 1 HMIS: 1 HMIS: 0 HMIS: PP = B
ACUTE EFFECTS OF OVEREXPOSURE:
- EYE: Mildly irritating to the eyes.
- SKIN: May cause moderate skin irritation. May aggravate existing dermatitis.
- INHALATION: Breathing mist may cause mild irritation to upper respiratory tract.
- INGESTION: Do not take internally. Seek immediate medical attention.
CHRONIC EFFECTS OF OVEREXPOSURE: Repeated prolonged contact may produce irritation. Do not ingest or swallow.
OTHER HEALTH EFFECTS (MEDICAL CONDITIONS GENERALLY AGGREVATED BY EXPOSURE): People with sensitive
skin can experience aggravated skin irritation. No other known applicable information.
SECTION 4: EMERGENCY FIRST AID PROCEDURES
- EYE: Immediately flush eyes with running water for at least 15 minutes. Seek immediate medical attention.
- SKIN: Remove from skin with water flush and soap. If irritation or adverse symptoms continue, seek medical
attention.
- INHALATION: Remove to fresh air. If breathing difficult, seek medical attention immediately.
- INGESTION: Do not take internally. DO NOT induce vomiting. Seek medical attention immediately.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point: 212 癋 / 100 癈 (Closed Cup) Autoignition Temperature: Not determined.
Flammability Limits in Air: Not determined. Extinguishing Media: On large fires use dry chemical, foam or water spray.
On small fires use carbon dioxide (CO2), dry chemical or water spray. Water can be used to cool fire exposed containers.
Fire Fighting Measures: Self-contained breathing apparatus and protective clothing should be worn in fighting large fires
involving chemicals. Use water spray to keep fire exposed containers cool. Determine the need to evacuate or isolate the area
according to your local emergency plan. Unusual Fire Hazards: None
Hazardous Decomposition Products: Thermal breakdown of this product during fire or very high heat conditions may evolve
the following hazardous decomposition products: Carbon oxides and traces of incompletely burned carbon compounds. Silicon
dioxide. Nitrogen oxides. Hydrogen. Formaldehyde. Ethyl alcohol is formed upon contact with water or humid air. Provide
adequate ventilation to control exposures within guidelines of OSHA PEL and ACGIH TLV: TWA 1000 ppm. When heated to
temperatures above 150 degrees C in the presence of air, product can form formaldehyde vapors. Formaldehyde is a potential
cancer hazard, a known skin and respiratory sensitizer, and an irritant to the eyes, nose, throat, skin, and digestive system. Safe
handling conditions may be maintained by keeping vapor concentrations within the OSHA Permissible Exposure Limit for
formaldehyde.
SECTION 6. ACCIDENTAL RELEASE MEASURES
Containment/Clean up: Observe all personal protection equipment recommendations described in Sections 5, 7 and 8. For
large spills, provide diking or other appropriate containment to keep material from spreading. If diked material can be pumped,
store recovered material in appropriate vented container. Materials in contact with water, moisture, acids or bases have the
potential to generate hydrogen gas. Recovered material should be stored in a vented container. Clean up remaining materials
from spill with suitable absorbent. Clean area as appropriate since spilled materials, even in small quantities, may present a slip
hazard. Dispose of saturated absorbent or cleaning materials appropriately, since spontaneous heating may occur. Local, state
and federal laws and regulations may apply to releases and disposal of this material, as well as those materials and items
employed in the cleanup of releases. Determine which federal, state and local laws and regulations are applicable. Sections 13
and 15 of this MSDS provide information regarding certain federal and state requirements. See section 8 for Personal Protective
Equipment for Spills
SECTION 7. HANDLING AND STORAGE
Use in well-ventilated area away from sparks and open flames. Do not smoke in vicinity. Product evolves minute
flammable ethyl alcohol on exposure to water or humid air. Provide ventilation during use to control ethanol within exposure
guidelines or use respiratory protection. Avoid eye and skin contact. Chemical splash goggles are recommended. Do not take
internally. Product evolves minute quantities of flammable hydrogen gas which can accumulate in non-ventilated areas.
Adequately ventilate to maintain vapors well below flammability limits and exposure guidelines. Do not repackage. Do not store in
glass containers which may shatter due to pressure build up. Clogged container vents may increase pressure build up. Keep
container closed and store away from water or moisture.
MSDS SOLO SEAL
SECTION 8: PERSONAL PROTECTION
Do not smoke in vicinity of application. Appropriate personal protective equipment necessary to prevent prolonged contact
should be worn. Use in well-ventilated area or mechanical ventilation is recommended. Avoid prolonged breathing of mist or
vapors. Where high concentrations of mist occur, a respirator with appropriate dust and mist removal capabilities is
recommended. Eye protection and resistant clothing, boots and gloves should be worn where high concentrated spills or
splashing can occur. Chemical splash goggles are recommended. A single prolonged skin exposure is not likely to result in skin
irritation or absorption through the skin in harmful amounts. Do not take internally. Eye wash station should be available.
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical Form: Liquid Color: White Odor: Some odor Specific Gravity @ 25癈: 1 Viscosity: 50 cSt
Freezing/Melting Point: Not determined. Boiling Point: 100 癈 Vapor Pressure @ 25癈: Not determined.
Vapor Density: Not determined. Solubility in Water: Not determined. pH: Not determined. Volatile Content: Undetermined.
SECTION 10: STABILITY AND REACTIVITY
Chemical Stability: Stable. Hazardous Polymerization: Hazardous polymerization will not occur.
Conditions to Avoid: None. Materials to Avoid: Oxidizing material can cause a reaction. Water, alcohols, acidic or basic
materials, and many metals or metallic compounds, when in contact with product, liberate flammable hydrogen gas, which can
form explosive mixtures in air.
SECTION 11: TOXICOLOGICAL INFORMATION
Special Hazard Information on Components No known applicable information.
SECTION XII: ECOLOGICAL INFORMATION
Environmental Fate and Distribution: Complete information is not yet available. Environmental Effects: Complete
information is not yet available. Fate and Effects in Waste Water Treatment Plants: Complete information is not yet available.
Ecotoxicity Classification Criteria: Hazard Parameters (LC50 or EC50). Acute Aquatic Toxicity (mg/L) <=1 (high).>1 and
<=100 (medium); >100 (low). Acute Terrestrial Toxicity <=100(high); >100 and <= 2000 (medium); >2000(low) Adapted from
"Environmental Toxicology and Risk Assessment", ASTM STP 1179, p.34, 1993. Can be used to classify the ecotoxicity of this product when
ecotoxicity data is listed above. Please read the other information presented in the section concerning the overall ecological safety of this
material.
SECTION 13: DISPOSAL CONSIDERATIONS
When a decision is made to discard this material, state or local laws may impose additional regulatory requirements
regarding disposal. Small quantities may be cleaned with soap and water, and then flushed to a sanitary or industrial
sewer. Absorbent material containing small amounts of the material may be disposed in appropriate land fills.
Disposal of large quantities should comply with applicable disposal permits and regulatory laws. Characteristic
Waste: Reactive D003
SECTION 14: TRANSPORT INFORMATION
-DOT SHIPPING NAME (49CFR 172.101): Non Flammable Liquid, NOS, water-based Mixture of Silanes
- DOT ID# (49CFR 172.101): Non-Regulated - DOT HAZARD CLASS: Non Flammable Liquid, NOS
-LABEL: None Required - PLACARD: None Required Air Shipment (IATA): not IATA regulated. Vented
packages forbidden for air transport. Ocean Shipment: Not subject to IMDG code
International Harmonic System Code: 3402
SECTION 15: REGULATORY INFORMATION
Contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200. TSCA Status: All chemical
substances in this material are included on or exempted from listing on the TSCA Inventory of Chemical Substances.
EPA SARA Title III Chemical Listings: Section 302 Extremely Hazardous Substances: None.
Section 304 CERCLA Hazardous Substances: None. Section 312 Hazard Class: Acute: Yes. Chronic: No. Fire: No
Pressure: No. Reactive: Yes. Section 313 Toxic Chemicals: None present or none present in regulated quantities.
Supplemental State Compliance Information:
California: Warning: This product contains the following chemical(s) listed by the State of California under the Safe Drinking
Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other reproductive
harm. CAS Number: 75-07-0. Wt %: <0.1. Component Name: Acetaldehyde (Carcinogenic).
Massachusetts: CAS Number: 75-07-0. Wt %: <0.1 Component Name: Acetaldehyde.
New Jersey: [CAS Number: 7732-18-5. Wt %:40.0 - 70.0. Component Name: Water.] [Case Number: 68037-59-2. Wt % 5.0 -
7.0. Component Name: Dimethyl, methylhydrogen siloxane]. [Case Number: 2943-75-1. Weight %: 5.0 - 7.0. Component Name:
N-Octyltriethoxysilane.] [Case Name: 9002-92-0. Wt %: 0.5-1.0. Component Name: Polyethylene oxide lauryl ether.]
Pennsylvania: [Case Number: 68037-59-2. Wt %: 40.0 - 70.0. Component Name: Water.] [Case Number: 68037-59-2.
Wt%: 5.0 - 7.0 Component Name: Dimethyl, methylhydrogen siloxane.] [Case Number: 2943-75-1. Wt %:5.0 - 7.0
Component Name: N-Octyltriethoxysilane].
SECTION 16: OTHER INFORMATION
All terms and abbreviations have been defined in various government publications, or are standard chemical terms used by IUPAC.
The data and recommendations herein are based upon our research and the research of others, and are believed to be accurate. However,
no warranty or guarantee of their accuracy is made; and the products are distributed without warranty, expressed or implied, including the limited
warranties of merchantability of fitness for particular purpose. The recommended industrial hygiene and safe handling procedures are believed to
be generally applicable. However, each user should review these recommendations in the specific context of the intended use and determine
whether they are appropriate.
Neither this data sheet nor any statement contained herein grants or extends any license, express or implied, in connection with patents
issued or pending which may be the property of the manufacturer or others. The manufacturer makes no warranties, expressed or implied, as to
the accuracy or adequacy of the information contained herein. The manufacturer shall not be liable to the vendee, the vendee's employees or
anyone for any direct, special or consequential damages arising out of or in connection with this accuracy, adequacy or furnishing of such
information.
|