EMERGENCY PHONE: 1-800-424-9300 Chemtrec
INTERNATIONAL TRANSPORTATION ACCIDENTS: 1-703-527-3887 Chemtrec
I. CHEMICAL PRODUCT IDENTIFICATION
Product Name : 030FD White Strippable Booth Coating
Date Printed : 07/05/03
Revision Date : 03/18/08 Revision Number : 1
Supercedes : None CHEMCO INFORMATION:800-323-0431 WWW.CHEMCOMFG.COM
II. COMPOSITION/INFORMATION ON INGREDIENTS - (EXPOSURE LIMITS - SEE SECTION VIII)
INGREDIENT NAME CAS # %
Water - for information only 7732-18-5 40.01 - 50.00
Calcium carbonate 471-34-1 10.01 - 15.00
Titanium dioxide 13463-67-7 1.01 - 5.00
Propylene Glycol 57-55-6 1.01 - 5.00
Diethylene glycol mono-n-butyl ether 112-34-5 1.01 - 5.00
Butyl Benzyl Phthalate 85-68-7 1.01 - 5.00
If ingredient percentages do not total 100%, the balance is due to rounding or applies to ingredient(s) deemed nonhazardous under 29 CFR 1910.1200 (Hazard Communication Standard).
III. HAZARDS IDENTIFICATION
HMIS
1
HEALTH
2
FLAMMABILITY
0
REACTIVITY
0 = Least 1 = Slight 2 = Moderate 3 = High 4 = Extreme * = Chronic Health Effects
Routes of Entry: Inhalation, Ingestion, Skin contact, Eye contact, Absorption.
Lung disease, Eye disease, Skin disease including eczema and sensitization.
Medical Conditions Aggravated:
Immediate (Acute) Health Effects:
Can cause minor respiratory irritation, dizziness, weakness, fatigue, nausea, and headache.
Inhalation:
Can cause minor skin irritation, defatting, and dermatitis.
Skin Contact:
Contact with the eyes may cause moderate to severe eye injury. Eye contact may result in tearing and
Eye Contact:
reddening, but not likely to permanently injure eye tissue. Temporary vision impairment (cloudy or
blurred vision) is possible.
May cause irritation and minor systemic damage.
Skin Absorption:
May be slightly toxic by ingestion. Can cause abdominal discomfort, nausea, vomiting and diarrhea.
Ingestion:
Respiratory System, Eyes, Skin.
Target Organ Acute Toxicity:
Long-Term (Chronic) Health Effects:
Upon prolonged and/or repeated exposure, can cause minor respiratory irritation, dizziness, weakness,
Inhalation:
fatigue, nausea, and headache.
Upon prolonged or repeated contact, can cause minor skin irritation, defatting, and dermatitis.
Skin Contact:
CHEMCO MFG. CO., INC. 515 HUEHL ROAD, NORTHBROOK, IL 60062 PH:800-323-0431 WWW.CHEMCOMFG.COM
Page 1 of 5
Upon prolonged or repeated contact, can cause moderate to severe eye injury. Eye contact may result
Eye Contact:
in tearing and reddening, but not likely to permanently injure eye tissue. Temporary vision impairment
(cloudy or blurred vision) is possible.
Upon prolonged or repeated exposure, harmful if absorbed through the skin. May cause minor
Skin Absorption
systemic damage.
IARC: No NTP: No OSHA: No
Carcinogenicity:
Respiratory System, Eyes, Skin.
Target Organ Chronic Toxicity:
NOTICE - Reports have associated repeated and prolonged occupational overexposure to solvents with
brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the
contents may be harmful or fatal.
This product contains pigments which may become a dust nuisance when removed by abrasive
blasting, sanding or grinding.
IV. FIRST AID
Remove to fresh air. If breathing is difficult, have a trained individual administer oxygen. Seek
Inhalation:
medical attention if symptoms persist.
Immediately flush eyes with plenty of luke warm water for at least 20 minutes retracting eyelids often.
Eyes:
Tilt the head to prevent chemical from transferring to the uncontaminated eye. Get immediate medical
attention and monitor the eye daily as advised by your physician.
Wash with soap and water. Get medical attention if irritation develops or persists. As a good general
Skin Contact:
hygienic rule, if clothing comes in contact with the product, the clothing should be laundered before
re-use.
Seek medical advice immediately. Provide ingredients information from Section II of this MSDS to
Ingestion:
the medical care provider. Contact your local Poison Control Center (listed in the telephone book), or
dial the local "Emergency" (911) number for additional information. Do not induce vomiting unless
instructed to do so by a physician or other competent medical personnel. Never give anything by
mouth to an unconscious person.
V. FIRE FIGHTING MEASURES
Liquid material not combustible
Flammability Summary:
N/A
Flash Point:
N/A
Autoignition Temperature:
0.8 24.6
Lower Flammable/Explosive Limit, % in air: Upper Flammable/Explosive Limit, % in air:
Material may be ignited if preheated to temperatures above the flash point in the presence of a source
Fire Hazards:
of ignition. This product, when dried or cured, may support combustion when subjected to sources of
ignition or heat in sufficient amount.
Use alcohol resistant foam, carbon dioxide, dry chemical, or water spray when fighting fires. Water or
Extinguishing Media:
foam may cause frothing if liquid is burning but it still may be a useful extinguishing agent if carefully
applied to the fire. Do not direct a water stream directly into the hot burning liquid.
Do not enter fire area without proper protection including self-contained breathing apparatus and full
Fire Fighting Instructions:
protective equipment. Fight fire from a safe distance and a protected location due to the potential of
hazardous vapors and decomposition products.
Carbon dioxide, Carbon monoxide.
Hazardous Combustion Products:
CHEMCO MFG. CO., INC. 515 HUEHL ROAD, NORTHBROOK, IL 60062 PH:800-323-0431 WWW.CHEMCOMFG.COM
Page 2 of 5
VI. ACCIDENTAL RELEASE MEASURES
Exposure to the spilled material may be irritating or harmful. Follow personal protective equipment
Health Consideration for Spill Response:
recommendations found in Section VIII of this MSDS. Additional precautions may be necessary based
on special circumstances created by the spill including: the material spilled, the quantity of the spill,
and the area in which the spill occurred. Also consider the expertise of employees in the area
responding to the spill. Isolate area. Keep unnecessary personnel away. Persons not wearing
appropriate protective equipment should be excluded from area of spill until clean-up has been
completed.
Spill Mitigation Procedures:
Prevent the spread of any spill to minimize harm to human health and the environment if safe to do so.
General Methods:
Wear complete and proper personal protective equipment following the recommendation of Section
VIII at a minimum. Dike with suitable absorbent material like granulated clay. Gather and store in a
sealed container pending a waste disposal evaluation.
Ventilate the area by opening door and/or turning on fans and blowers.
Air Release:
Retain all contaminated water for treatment.
Water Release:
Avoid runoff into storm sewers and ditches that lead to waterways.
Land Spills:
VII. HANDLING AND STORAGE
Mildly irritating material. Avoid unnecessary exposure. As with all chemicals, good industrial hygiene
Handling:
practices should be followed when handling this material. Follow all protective equipment
recommendations provided in Section VIII.
Store in a cool dry place. Isolate from incompatible materials. Keep container closed when not in use.
Storage:
Avoid exposure to sunlight or ultraviolet (UV) light sources
VIII. ENGINEERING CONTROLS, PERSONAL PROTECTIVE EQUIPMENT, AND EXPOSURE LIMITS
Local exhaust ventilation, process enclosures, or other engineering controls are necessary when
Engineering Controls:
handling or using this product to avoid overexposure.Use process enclosures, local exhaust ventilation,
or other engineering controls to control airborne levels below recommended exposure limits. Vapor
concentrations should be monitored and controlled in accordance with 29 CFR 1910.1000.
Protective Equipment:
If general or local exhaust ventilation is not available or sufficient to reduce exposure to below
Respiratory Tract:
acceptable levels, then respiratory protection is required to avoid overexposure when handling this
product.
Wear safety glasses with side shields when handling this product. When the possibility exists for eye
Eyes:
contact with splashing or spraying liquid, or airborne material, wear additional eye protection such as
chemical splash goggles and/or face shield . Do not wear contact lenses. Have an eye wash station
available.
Not normally considered a significant skin irritant. Where use can result in skin contact, practice good
Skin:
personal hygiene and wear a barrier cream and/or impervious gloves. Wash hands and other exposed
areas with mild soap and water before eating, drinking, and when leaving work.
Wear chemically resistant gloves and apron. (Consult your safety equipment supplier).
Protective Clothing:
CHEMCO MFG. CO., INC. 515 HUEHL ROAD, NORTHBROOK, IL 60062 PH:800-323-0431 WWW.CHEMCOMFG.COM
Page 3 of 5
CHEMICAL NAME CAS ACGIH TLV OSHA PEL IDLH
#
Water - for information only 7732-18-5 No TLV No PEL established Not determined.
Calcium carbonate 471-34-1 No TLV No PEL established Not determined.
Titanium dioxide 13463-67-7 10 mg/m3 TWA 15 mg/m3 TWA (total dust) 5,000 mg/m3 IDLH
Propylene Glycol 57-55-6 No TLV No PEL established Not determined.
Diethylene glycol mono-n- 112-34-5 No TLV No PEL established Not determined.
butyl ether
Butyl Benzyl Phthalate 85-68-7 No TLV No PEL established Not determined.
IX. PHYSICAL DATA
White Liquid.
Appearance:
White
Color:
N/A
pH:
Not Determined.
Octanol/Water Coeff:
Partial.
Solubility in Water:
Heavier than air. Vapors that evolve from this product will tend to settle and accumulate near the floor.
Vapor Density:
Not determined
Evaporation Rate:
1.151 / 9.61 Lbs./Gl.
Specific Gravity/Density:
1.0 Lbs/Gl less water & 120 g/l less water & 0.4 Lbs/Gl as
V.O.C.
exempt solvent; exempt solvent; packed
The VOC content is determined by using a percent solids basis, less water and exempt solvents, for adhesives, coatings and inks and the calculations of EPA
Reference Method 24 or equivalent ASTM method approved by the executive office.
100 ?C; 212 ?F
Initial Boiling Point:
0 ?C; 32 ?F
Initial Freezing Point:
X. STABILITY AND REACTIVITY
Stable under normal conditions.
Stability Information:
Temperatures above flash point in combination with sparks, open flames, or other sources of
Conditions to Avoid:
ignition.Contamination.Do not freeze.
Strong oxidizing agents.
Chemical Incompatibility:
Carbon dioxide, Carbon monoxide.
Hazardous Decomposition Products:
XI. TOXICOLOGICAL INFORMATION
Chemical Name LD50/LC50
Carbonic acid, calcium salt (1:1) Oral LD50 Rat : 6450 mg/kg
1,2-Propanediol Oral LD50 Rat : 20 gm/kg; Oral LD50 Mouse : 22 gm/kg; Dermal LD50 Rabbit : 20800 mg/kg
Ethanol, 2-(2-butoxyethoxy)- Oral LD50 Rat : 5660 mg/kg; Oral LD50 Mouse : 2400 mg/kg; Dermal LD50 Rabbit : 2700 mg/kg
Butyl Benzyl Phthalate Oral LD50 Rat : 2330 mg/kg; Oral LD50 Mouse : 4170 mg/kg; Dermal LD50 Rabbit : >10 gm/kg
XII. ECOLOGICAL INFORMATION
Care should be taken to minimize releases of any industrial chemicals to the environment.
Overview:
CHEMCO MFG. CO., INC. 515 HUEHL ROAD, NORTHBROOK, IL 60062 PH:800-323-0431 WWW.CHEMCOMFG.COM
Page 4 of 5
XIII. DISPOSAL CONSIDERATIONS
Spent or discarded material is not expected to be a hazardous waste.
Waste Description for Spent Product:
Information in this MSDS is provided only as a guide. Consult with competent authority to determine
Disposal Methods:
proper waste disposal procedures. Clean up and dispose of waste and clean-up materials in accordance
with all federal, state, and local environmental regulations.
Not determined., .
Potential EPA Waste Codes:
Some Components Possibly Subjected to USEPA Land Disposal Restrictions:
When disposing of unused products or any waste, the preferred options are to send to a licensed reclaimer or to permitted incinerators. There may be some other ingredients subject to LDR categories.
Butyl benzyl phthalate 85-68-7
XIV. TRANSPORTATION INFORMATION
Agency Basic Description and Label
Not regulated per DOT.
DOT
Hazardous Substance
Butyl benzyl phthalate final RQ = 100 pounds (45.4 kg)
XV. REGULATORY INFORMATION
Regulation
SARA 313 Reportable : Ethanol, 2-(2-butoxyethoxy)-
TSCA Inventory : All components of this product are listed in, or exempt from, the TSCA 8(b) Inventory.
M.S.D.S. Reportable HAP(s) : Diethylene glycol mono-n-butyl ether.
California Proposition 65 : The following statement is made in order to comply with the California Safe Drinking Water and Toxic Enforcement Act of 1986 -
Proposition 65: "WARNING: This product contains chemical(s) known to the State of California to cause cancer and birth defects or
other reproductive harm."
XVI. ADDITIONAL INFORMATION
Major References: VENDOR'S MSDS's, PAINT & COATINGS HANDBOOK, EPA's LIST OF LISTS, AND OTHER PUBLISHED MATERIALS.
IMPORTANT: WHILE THE DESCRIPTIONS, DATA AND INFORMATION CONTAINED HEREIN ARE PRESENTED IN GOOD FAITH AND BELIEVED TO BE ACCURATE, THEY ARE
PROVIDED FOR YOUR GUIDANCE ONLY. BECAUSE MANY FACTORS MAY AFFECT PROCESSING OR APPLICATION/USE, WE RECOMMEND THAT YOU PERFORM AN ASSESSMENT TO
DETERMINE THE SUITABILITY OF A PRODUCT FOR YOUR PARTICULAR PURPOSE PRIOR TO USE. NO WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING
FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED, DATA OR INFORMATION SET FORTH. IN NO CASE SHALL THE DESCRIPTIONS,
INFORMATION, OR DATA PROVIDED BE CONSIDERED A PART OF OUR TERMS AND CONDITIONS OF SALE. FURTHER, THE DESCRIPTIONS, DATA AND INFORMATION FURNISHED
HERE ARE GIVEN GRATIS. NO OBLIGATIONS NOR LIABILITIES FOR THE DESCRIPTION, DATA AND INFORMATION GIVEN ARE ASSUMED. ALL SUCH BEING GIVEN AND ACCEPTED
AT YOUR RISK.
CHEMCO MFG. CO., INC. 515 HUEHL ROAD, NORTHBROOK, IL 60062 PH:800-323-0431 WWW.CHEMCOMFG.COM
Page 5 of 5
|