MATERIAL SAFETY DATA SHEET
I. PRODUCT IDENTIFICATION
Name: Armstrong S-599 Premium Vinyl-Backed Flooring Adhesive
Description: Water Based Adhesive
S-599
II. DEPARTMENT OF TRANSPORTATION INFORMATION
Shipping name: Not classified. Hazard Class: DOT Non-hazardous
ID #: N/A Packing Inst.: N/A DOT/IMO/IATA: N/A Prepared 6/06
Common Carrier NMSFC#: N/A
Armstrong World Industries, Inc.
EMERGENCY ONLY CONTACT: CHEM-TEL 800-255-3924
P. O. Box 3001
Lancaster, PA 17604
III. HMIS (0=minimal hazard; 4 = severe hazard)
www.armstrong.com
Health = 1 Flammability = 0 Reactivity = 0
MSDS Requests: www.floorexpert.com
Technical Services
IV. PRODUCT CONTENT
1-877-276-7876, Option 2, 3, and 3
This product does not contain chemicals subject to the reporting
requirements of Section 313 of SARA Title III and 40 CFR 372. All
components are on TSCA inventory. This product does NOT contain
asbestos.
V. HAZARDOUS INGREDIENTS
(Chemical Identity; Common Name) C.A.S. No. % OSHA PEL ACGIH TLV
None N/A N/A N/A N/A
contents in accordance with Federal, State and Local Waste
VI. PHYSICAL DATA
Disposal Regulations. Do not flush unused contents or residue
APPEARANCE AND COLOR: Yellow. ODOR: Mild.
down drains.
BOILING POINT (degrees F): N/K. VAPOR PRESSURE: Low.
VAPOR DENSITY: Low. SOLUBILITY IN WATER: Miscible.
XI. SPECIAL HANDLING AND USE INFORMATION
SPECIFIC GRAVITY: N/K. EVAPORATION RATE: N/A. VOC:
VENTILATION: Local Exhaust / normal ambient ventilation
o o
Less than 14 g/l calculated at 70 F/21 C, SCAQMD.
should be sufficient. Open doors and windows to provide
VII. FIRE AND EXPLOSION HAZARD DATA
cross-ventilation if necessary. RESPIRATORY PROTECTION:
FLASH POINT: N/A. FLAMMABLE LIMITS IN AIR, 5 BY With adequate ventilation, respiratory equipment should not be
VOLUME: LEL = N/A; UEL = N/A. EXTINGUISHING MEDIA: needed. SKIN AND EYE PROTECTION: It is always a good
Water spray, carbon dioxide, foam or dry chemical. SPECIAL safety practice to avoid contact with eyes and prolonged
FIRE FIGHTING ROCEDURES: Protect fire fighters from toxic contact with skin. If contact may occur, use spectacle-type
products of combustion by wearing self-contained breathing glasses and latex or rubber gloves.
apparatus.
XII. SPECIAL PRECAUTIONS
VIII. HEALTH HAZARD DATA
PRECAUTIONS TO BE TAKEN IN HANDLING AND
PRIMARY ROUTES OF ENTRY: Skin, eyes. TARGET STORAGE: Keep from freezing. Recommended storage
ORGANS: N/A. EFFECTS OF OVEREXPOSURE: SKIN temperature is between 50 to 90 degrees F. OTHER
AND EYES: Avoid skin and eye contact. May produce PRECAUTIONS: None. WORK SITE ENVIRONMENT: Initially
irritation to eyes and skin. INHALATION: May cause slight there may be a potential adverse impact on indoor air quality
irritation to the upper respiratory tract. CARCINOGENICITY: within the general work area during the installation process.
NTP: No. IARC Monographs: No. OSHA Regulated: No. Therefore you should advise the building manager or other
FIRST AID PROCEDURES: EYES AND SKIN: Upon eye appropriate person that:
contact, flush eyes with water for at least 15 minutes. Upon ?It will be necessary to establish and maintain adequate
skin contact, wash with soap and water. Refer to a physician if ventilation of the work area, without causing the entry of
irritation or symptoms persist. INHALATION: Move person to contaminants to other parts of the building; and ?Persons who
fresh air. Refer to a physician if irritation or symptoms persist. are sensitive to odors and/or chemicals should be advised to
IX. REACTIVITY DATA avoid the work area during this process.
STABILITY: Stable. INCOMPATIBILITY: Metal salts may
coagulate this product. HAZARDOUS DECOMPOSITION The information presented herein is supplied as a guide to
PRODUCTS: Carbon monoxide, carbon dioxide, and other those who handle or use this product. Safe work practices
toxic vapors and gases that are common to thermal must be employed when working with any materials. It is
degradation of organic compounds. HAZARDOUS important that the end user makes a determination regarding
POLYMERIZATION: Will not occur. the adequacy of the safety procedures employed during the
use of this product.
X. SPILL OR LEAK PROCEDURES
SPILL OR LEAK HANDLING: Keep out of sewer systems.
Use absorbent and scrape up to collect. Place into closed
N/A - not applicable or not available
containers for disposal. WASTE DISPOSAL METHOD: Do not
N/K - none known or not known
reuse container. Dispose of container and any unused
|