MATERIAL SAFETY
DATA SHEET
MSDS Number: 249-A-252
CleanSafe?Dust Remover
Issue Date: 11-17-05
Manufacturer MSDS Assistance Transportation Emergency
IQ Products Company IQ Phone: (281) 444-6454 CHEMTREC: (800) 424-9300
Houston, TX 77086-1014 IQ Fax: (281) 444-0185 Outside U.S. (703) 527-3887
Section 1 Product Identification
COMMON NAME ON LABEL CHEMICAL FAMILY
CleanSafe ?Dust Remover Hydrofluorocarbons
Section 2 Information on Ingredients
Component CAS No. OSHA ACGIH ACGIH
PEL TLV-TWA TLV-STEL
1,1-DIFLUOROETHANE (HFC-152a) 75-37-6 None Established None Established None Established
Section 3 Physical and Chemical Properties
PHYSICAL FORM Liquefied gas COLOR Clear, colorless
ODOR Faint ether-like odor % VOLATILES 100 WT%
Section 4 Firefighting Measures
EXTINGUISHING MEDIA: Water Spray, Water Fog, Dry Chemical, Carbon Dioxide, and "Alcohol" Foam
SPECIAL FIRE FIGHTING PROCEDURES: Firefighters should wear a self-contained breathing apparatus and protective clothing if containers
rupture and contents are release under fire conditions.
UNUSUAL FIRE AND EXPLOSION Fire decomposition by-products will include hydrofluoric acid, and possibly carbonyl fluoride. Avoid
HAZARDS: contact with these materials, which are toxic and irritating. Evacuate personnel immediately in the
event of a fire.
Section 5 Health Hazard Data
EFFECTS OF OVEREXPOSURE EMERGENCY AND FIRST AID PROCEDURES
Flush eyes with water for 15 minutes. Get medical
EYES EYES
Eye Contact with Liquid: Can cause eye irritation. Can attention if irritation persists.
cause frostbite.
Flush the exposed area of the skin with lukewarm
SKIN SKIN
Skin Contact with Liquid: Can cause skin irritation. (not hot) water. Get medical attention if frostbitten.
Can cause frostbite.
Remove affected person to fresh air. If not
INHALATION INHALATION
Inhalation misuse by deliberately concentrating and breathing, give artificial respiration and get medical
inhaling the contents can be harmful or fatal. attention. If breathing is difficult, give oxygen.
PAGE 1 of 2
MSDS Number: 249-A-252
CleanSafe?Dust Remover
Issue Date: 11-17-05
Ingestion is not considered a potential route of
INGESTION INGESTION
Not Applicable exposure.
Section 6 Stability and Reactivity Data
n STABLE CONDITIONS TO AVOID:
STABILITY
q UNSTABLE Material is stable. However avoid open flames and high temperatures.
INCOMPATIBILITY: Incompatibility with alkali or alkaline earth metals ?powdered Al, Zn, Be, etc.
q MAY OCCUR
POLYMERIZATION: CONDITIONS TO AVOID:
n WILL NOT OCCUR Not Applicable
DECOMPOSITION PRODUCTS: This material can be decomposed by high temperatures forming hydrofluoric acid and possibly carbonyl fluoride.
Section 7 Spill or Leak Procedures
STEPS TO BE TAKEN IN CASE MATERIAL RELEASE: Ventilate area, especially low or enclosed places where heavy vapors might collect. Remove
open flames. Use self-contained breathing apparatus (SCBA) if large spill or leak occurs.
WASTE DISPOSAL METHOD: Always package, store, transport, and dispose of all waste and contaminated equipment in accordance with all
applicable federal, state, and local health and environmental regulations.
Section 8 Special Protection Information
EYE PROTECTION: Wear protective eyewear to avoid injury from dust and debris.
SKIN PROTECTION: Avoid skin contact with freezing liquid. If skin contact cannot be avoided then synthetic rubber gloves should be worn while
using this product. Lined synthetic rubber gloves are recommended.
RESPIRATORY PROTECTION: Avoid breathing high concentrations of vapor. Reduce exposure levels below the recommended exposure limits. The
recommended workplace exposure level (8-hour TWA) is 1,000 ppm as established by the American Industrial Hygiene Association (AIHA).
MECHANICAL VENTILATION: Local mechanical exhaust ventilation should be used to reduce exposure limits below the recommended levels.
OTHER PROTECTIVE EQUIPMENT: Add additional protective equipment necessary to avoid inhalation, skin contact, and eye contact with the
product.
Section 9 Product Label Information
Read and observe all DIRECTIONS and WARNING statements on the product label.
DIRECTIONS: USE THIS PRODUCT ONLY AS DIRECTED. Wear protective eyewear to avoid injury from dust and debris. Prior to first use, remove
safety tab on spray applicator top. HOLD CAN UPRIGHT before and during use. Do not use this product while holding can upside down or at an
angle which will dispel a flammable, freezing liquid that may cause injury or ignite if exposed to open flame or other ignition source. Unplug
electronic devices before using this product. Hold can approximately two inches from item to be dusted. Operate a short series of blasts. Attach
extension tube to remove hard-to-reach debris.
WARNING: CONTENTS UNDER PRESSURE. AVOID EYE CONTACT. AVOID SKIN CONTACT WITH FREEZING LIQUID. AVOID INHALATION. KEEP
OUT OF REACH OF CHILDREN. Do not puncture or incinerate container. Do not expose to heat or store at temperatures above 120 癋 (49 癈). This
product contains IQ's unique Bittergent Technology to help deter misuse through intentional inhalation of concentrated vapors.
IMPORTANT NOTE: Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. More information about
inhalant abuse can be found at www.inhalant.org.
Section 10 Transportation Information
While the information and recommendations set forth herein are believed to be accurate,
we make no warranty with respect hereto and disclaim all liability from reliance thereon.
PAGE 2 OF 2 MSDS Prepared by: Marty A. York
MSDS Number: 249-A-252
CleanSafe?Dust Remover
Issue Date: 11-17-05
DOMESTIC GROUND TRANSPORTATION: Proper Shipping Name: CONSUMER COMMODITY, Hazard Class/Division: ORM-D
MODES OF TRANSPORTATION AUTHORIZED: Motor vehicle, rail freight, cargo vessel, and cargo aircraft only. The CARGO AIRCRAFT ONLY label
must be placed on each package intended for transportation by air. Contact MSDS Assistance at IQ Products Company for additional labeling
support.
This product is packaged under DOT Special Permit Number DOT-SP 11516.
MODAL REQUIREMENTS: A current copy of this Special Permit must be carried aboard each aircraft used to transport packages covered by this
special permit. The shipper must furnish a copy of this special permit to the air carrier before or at the time the shipment is tendered.
Section 11 Other Information
NPCA-HMIS Ratings: Health - 1, Flammability - 2*, Reactivity - 1 Personal protection rating to be supplied by user depending on use conditions.
Explanation of HMIS Ratings: Minimal - 0 Slight -1 Moderate - 2 Serious - 3 Severe - 4 *HMIS III Flammability Criteria for Aerosol Products
While the information and recommendations set forth herein are believed to be accurate,
we make no warranty with respect hereto and disclaim all liability from reliance thereon.
PAGE 2 OF 2 MSDS Prepared by: Marty A. York
|