Masters Cutting Oil
MATERIAL SAFETY DATA SHEET
================================================================================
SECTION I - PRODUCT IDENTIFICATION
================================================================================
Product name: MASTERS CUTTING OIL
Product use: Thread Cutting Lubricant
Chemical family: Hydrocarbon Cutting Oil
Supplier name and address: Manufacturer name and address:
G.F. THOMPSON CO. LTD. Refer to supplier
620 Steven Court, Unit #11
Newmarket, Ontario
L3Y 6Z2
Tel.: 905-898-2557
Emergency Tel. #: WHMIS CLASS: D2B
(905) 898-2557
================================================================================
SECTION II - INGREDIENTS
================================================================================
Components CAS# % (wt/wt)
Severely Solvent - Refined
Paraffinic Distillate 64741-88-4 20 - 30
Severely Solvent-Refined Residium 64742-62-7 60 - 75
Fatty Oils & Triglycerides 8016-28-2 1-5
Proprietary Additive 68425-16-1 1-5
================================================================================
SECTION III - PHYSICAL DATA
================================================================================
Physical State: Clear Liquid
Odour and appearance: Amber, Slight Sulphur Odour
Specific gravity: 0.900
Vapour pressure (mm Hg@ 20篊): < 0.1
Boiling point: > 121?C (>250篎)
pH: Not Determined
Vapour density: >1.0
Evaporation rate (BuAc = 1): Not Determined
Freezing Point: Not Determined
Volatiles, %: NIL
Solubility in water: NIL
VOC's: NONE
*This product contains no ingredient meeting the US EPA definition of VOC.
(see miscellaneous information)
Masters Cutting Oil
================================================================================
SECTION IV - FIRE AND EXPLOSION DATA
================================================================================
Conditions of Flammability: Open flames, sparks.
Extinguishing Media: Mechanical Foam, Alcohol Foam, Dry Chemical Powder,
Carbon Dioxide
Flash point (Method): 179篊 (355篎), COC Minimum
Upper Flammable Limit in Air % BV: Not determined
Lower Flammable Limit in Air % BV: Not determined
Hazardous Combustion Products: Oxides of Carbon, Sulphur, Nitrogen and minor amounts
of Hydrogen Sulphide.
Unusual Fire and Explosion Hazard: Container exposed to intense heat from fires should be
cooled with water to prevent vapour pressure build up which
could result in container rupture. Container areas exposed to
direct flame contact should be cooled with large quantities of
water as needed to prevent weakening of container structure.
Special Fire Fighting Procedures: Wear self contained breathing apparatus when fire fighting in
confined space. Cool fire exposed containers with water spray.
* * * NFPA CLASSIFICATION * * * * * * HAZARD RATING * * *
Health -1 0 - Least 3 - High
Fire -1 1 - Slight 4 - Extreme
Reactivity 0 2 - Moderate
================================================================================
SECTION V - REACTIVITY DATA
================================================================================
Stability: Stable.
Incompatible Materials: Strong oxidizing agents: Peroxides, Chlorine, Strong Acids, etc
Hazardous Polymerization: Material is not known to polymerize.
Hazardous Decomposition: Oxides of Carbon, Sulphur, Nitrogen and minor amounts of
Hydrogen Sulphide.
================================================================================
SECTION VI ?HEALTH HAZARD INFORMATION
================================================================================
*** Routes of entry ***
Inhalation: If heated, sprayed or misted, may cause chemical pneumontis.
Skin: Prolonged or repeated contact with skin may cause mild irritation.
Eyes: May be mildly irritating to eyes.
Ingestion: Low toxicity on ingestion. Has laxative effect.
Carcinogenicity: Not listed as a carcinogenic.
================================================================================
SECTION VII FIRST AID
================================================================================
Inhalation: If breathing is difficult, remove victim to fresh air, give artificial respiration if not
breathing.
Skin: Wash skin with soap and water or waterless hand cleaner. If irritation occurs, get
medical attention.
Eyes: In case of contact, flush eyes with large amounts of water for at least 15 minutes
Get medical attention.
Ingestion: Do not ingest. If ingested, do not induce vomiting. Get medical attention.
Page 2
Masters Cutting Oil
================================================================================
SECTION VIII - PREVENTIVE MEASURES
================================================================================
Spill, leak or release: If material is spilled or released to the atmosphere, steps should be taken to
prevent discharges to streams or sewer systems. Spills or releases should be
reported, if required to the appropriate local, provincial and federal regulatory
agencies.
Waste disposal: Clean up action should be carefully planned and executed. Shipment, storage
and /or disposal of waste materials are regulated and action to handle or dispose
of spilled or released materials must meet all local, provincial and federal rules.
Storage: Protect against physical damage. Separate from oxidizing materials. Store in cool
well ventilated area of non-combustible construction away from possible sources
of ignition.
*** PROTECTIVE EQUIPMENT ***
Respiratory protection: Not required under normal OSHA PEL. Use NIOSH approved respirators
to prevent over-exposure.
Ventilation: Use explosive proof ventilation as required to control vapour
concentration.
Protective gloves: Nitrile gloves provide best protection to hands and arms.
Eye protection: Safety glasses with side shields or goggles.
Personal Hygiene: Wear effective plant clothing. Contaminated clothing should be removed
and washed in soap and water. Cleanse skin thoroughly with soap and
water before meals. Shower and eyewash facilities should be accessible.
================================================================================
Miscellaneous Information
========================================================================
This product is formulated without the use of VOC's, and further there are no VOC's in this
product.
The EPA definition of a VOC (1997) is:
"Volatile organic compounds (VOC) means any compound of carbon, excluding carbon monoxide,
carbon dioxide, carbonic acid, metallic carbides or carbonates, and ammonium carbonate, which
participates is atmospheric photochemical reactions"
Additional notes or references:
Abbreviations:
N/Av: not available
N/Ap: not applicable
IARC: International Agency for Research on Cancer
ACGIH: American Conference of Governmental Industrial Hygienists
TLV: Threshold Limit Values
NIOSH: National Institute of Occupational Safety and Health
TDG: Transportation of Dangerous Goods Regulation.
BuAe: n-butyl acetate
Page 3
Masters Cutting Oil
References :
1. ACGIH, Threshold Limit Values and Biological Exposure Indices for 1988/89.
2. International Agency for Research on Cancer Monographs, Supplement 7, 1988.
3. Canadian Center for Occupational Health and Safety. RTECS database.
4. Material Safety Data Sheets from manufacturer.
5. N. Irving Sax. Dangerous Properties of Industrial Materials, Sixth Edition.
================================================================================
SECTION IX PREPARATION INFORMATION
================================================================================
Prepared by: G.F. THOMPSON CO. LTD.
Telephone #: 905-898-2557
Preparation date: December 1, 2006
================================================================================
Page 4
|