Material Safety Data Sheet
Date of issue 5 December 2008
Version 7.02
1. Product and company identification
Product name : *LOW VOC AQUAPON PASTEL BASE "A"
Code : 97-53
Supplier : PPG Industries, Inc.
One PPG Place
Pittsburgh, PA 15272
Emergency telephone : (412) 434-4515 (U.S.)
(514) 645-1320 (Canada)
number
01-800-00-21-400 (Mexico)
Technical Phone Number : 1-800-441-9695 (8:00 am to 5:00 pm EST)
2. Hazards identification
Emergency overview : DANGER!
FLAMMABLE LIQUID AND VAPOR. CAUSES RESPIRATORY TRACT, EYE AND
SKIN IRRITATION. MAY CAUSE ALLERGIC SKIN REACTION. MAY BE HARMFUL IF
INHALED, ABSORBED THROUGH SKIN OR SWALLOWED. ASPIRATION HAZARD.
CAN ENTER LUNGS AND CAUSE DAMAGE. PROLONGED OR REPEATED
CONTACT MAY DRY SKIN AND CAUSE IRRITATION. CONTAINS MATERIAL THAT
CAN CAUSE TARGET ORGAN DAMAGE.
Keep away from flames, such as a pilot light, and any object that sparks, such as an
electric motor. Keep away from heat. Do not smoke. Do not swallow. Do not get in
eyes or on skin or clothing. Avoid breathing vapor or mist. Use only with adequate
ventilation. Keep container tightly closed and sealed until ready for use. Wash
thoroughly after handling.
Potential acute health effects
Inhalation : May be harmful if inhaled. Irritating to respiratory system. Can irritate eyes, nose, mouth
and throat.
Ingestion : May be harmful if swallowed. Aspiration hazard if swallowed. Can enter lungs and
cause damage.
Skin : Harmful in contact with skin. Severely irritating to the skin. May cause an allergic skin
reaction.
Eyes : Severely irritating to eyes. Risk of serious damage to eyes.
Over-exposure signs/symptoms
Repeated exposure to high vapor concentrations may cause irritation of the respiratory system and permanent brain and
nervous system damage. Inhalation of vapor/aerosol concentrations above the recommended exposure limits causes
headaches, drowsiness and nausea and may lead to unconsciousness or death. There is some evidence that repeated
exposure to organic solvent vapors in combination with constant loud noise can cause greater hearing loss than expected
from exposure to noise alone.
Medical conditions : Pre-existing skin disorders and disorders involving any other target organs mentioned in
this MSDS as being at risk may be aggravated by over-exposure to this product.
aggravated by over-
exposure
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations
and the MSDS contains all the information required by the Controlled Products Regulations.
See toxicological information (section 11)
United States - Canada - Mexico Page: 1/9
Product code 97-53 Date of issue 5 December 2008 Version 7.02
Product name *LOW VOC AQUAPON PASTEL BASE "A"
3. Composition/information on ingredients
Name CAS number %
NJTS 80100337-5132 Proprietary 15 - 40
titanium dioxide 13463-67-7 10 - 30
propan-2-ol 67-63-0 7 - 13
xylene (mixture of o-, m-, p-isomers) 1330-20-7 3-7
1-methoxy-2-propanol 107-98-2 3-7
2-(propyloxy)ethanol 2807-30-9 1-5
silicon dioxide 7631-86-9 1-5
aluminium hydroxide 21645-51-2 1-5
ethylbenzene 100-41-4 0.5 - 1.5
solvent naphtha (petroleum), light arom. 64742-95-6 0.5 - 1.5
1,2,4-trimethylbenzene 95-63-6 0.1 - 1
mesitylene 108-67-8 0.1 - 1
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in
this section.
4. First aid measures
If ingestion, irritation, any type of overexposure or symptoms of overexposure occur during or persists after use of this
product, contact a POISON CONTROL CENTER, EMERGENCY ROOM OR PHYSICIAN immediately; have Material
Safety Data Sheet information available. Never give anything by mouth to an unconscious or convulsing person.
Eye contact : Check for and remove any contact lenses. Immediately flush eyes with running water
for at least 15 minutes, keeping eyelids open.
Skin contact : Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognized skin cleanser. Do not use solvents or thinners.
Inhalation : Remove to fresh air. Keep person warm and at rest. If not breathing, if breathing is
irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by
trained personnel.
Ingestion : If swallowed, seek medical advice immediately and show this container or label.
Keep person warm and at rest. Do not induce vomiting.
Notes to physician : No specific treatment. Treat symptomatically. Contact poison treatment specialist
immediately if large quantities have been ingested or inhaled.
5. Fire-fighting measures
Flammability of the product : Flammable liquid. In a fire or if heated, a pressure increase will occur and the container
may burst, with the risk of a subsequent explosion. Vapors may accumulate in low or
confined areas or travel a considerable distance to a source of ignition and flash back.
Runoff to sewer may create fire or explosion hazard.
Extinguishing media
Suitable : Use dry chemical, CO2, water spray (fog) or foam.
Not suitable : Do not use water jet.
Special exposure hazards : Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Hazardous combustion : Decomposition products may include the following materials:
carbon oxides
products
metal oxide/oxides
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
equipment for fire-fighters
United States - Canada - Mexico Page: 2/9
Product code 97-53 Date of issue 5 December 2008 Version 7.02
Product name *LOW VOC AQUAPON PASTEL BASE "A"
6. Accidental release measures
Personal precautions : No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources. No
flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment (see section 8).
Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Large spill : Stop leak if without risk. Move containers from spill area. Approach release from
upwind. Use spark-proof tools and explosion-proof equipment. Prevent entry into
sewers, water courses, basements or confined areas. Wash spillages into an effluent
treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and
place in container for disposal according to local regulations (see section 13). Dispose
of via a licensed waste disposal contractor. Contaminated absorbent material may pose
the same hazard as the spilled product. Note: see section 1 for emergency contact
information and section 13 for waste disposal.
Small spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble or absorb with
an inert dry material and place in an appropriate waste disposal container. Dispose of
via a licensed waste disposal contractor.
7. Handling and storage
Handling : Put on appropriate personal protective equipment (see section 8). Eating, drinking and
smoking should be prohibited in areas where this material is handled, stored and
processed. Persons with a history of skin sensitization problems should not be
employed in any process in which this product is used. Do not swallow. Do not get in
eyes or on skin or clothing. Avoid breathing vapor or mist. Use only with adequate
ventilation. Wear appropriate respirator when ventilation is inadequate. Do not enter
storage areas and confined spaces unless adequately ventilated. Keep in the original
container or an approved alternative made from a compatible material, kept tightly
closed when not in use. Store and use away from heat, sparks, open flame or any other
ignition source. Use explosion-proof electrical (ventilating, lighting and material
handling) equipment. Use non-sparking tools. Take precautionary measures against
electrostatic discharges. Vapors are heavier than air and may spread along floors. To
avoid fire or explosion, dissipate static electricity during transfer by grounding and
bonding containers and equipment before transferring material. Empty containers retain
product residue and can be hazardous. Do not reuse container. If this material is part of
a multiple component system, read the Material Safety Data Sheet(s) for the other
component or components before blending as the resulting mixture may have the
hazards of all of its parts.
Storage : Store in accordance with local regulations. Store in a segregated and approved area.
Store in original container protected from direct sunlight in a dry, cool and well-ventilated
area, away from incompatible materials (see section 10) and food and drink. Eliminate
all ignition sources. Separate from oxidizing materials. Keep container tightly closed
and sealed until ready for use. Containers that have been opened must be carefully
resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use
appropriate containment to avoid environmental contamination. Do not store above the
following temperature: 120F / 49C.
United States - Canada - Mexico Page: 3/9
Product code 97-53 Date of issue 5 December 2008 Version 7.02
Product name *LOW VOC AQUAPON PASTEL BASE "A"
8. Exposure controls/personal protection
Name Result ACGIH OSHA Ontario Mexico PPG
titanium dioxide TWA 10 mg/m?br>
15 mg/m?TD 10 mg/m?TD 10 mg/m?(as Not
Ti) established
STEL Not Not Not 20 mg/m?(as Not
established established established Ti) established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
propan-2-ol TWA 200 ppm 400 ppm 200 ppm 400 ppm Not
established
STEL 400 ppm Not 400 ppm 500 ppm Not
established established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
xylene (mixture of o-, m-, p- TWA 100 ppm 100 ppm 100 ppm 100 ppm Not
isomers) established
STEL 150 ppm Not 150 ppm 150 ppm Not
established established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
1-methoxy-2-propanol TWA 100 ppm Not 100 ppm Not Not
established established established
STEL 150 ppm Not 150 ppm Not Not
established established established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
2-(propyloxy)ethanol TWA Not Not 25 ppm Not 25 ppm
established established established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
silicon dioxide TWA Not Not Not 10 mg/m? Not
established established established 3 mg/m?R established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
aluminium hydroxide TWA Not Not 2 mg/m? 2 mg/m? Not
established established established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
ethylbenzene TWA 100 ppm 100 ppm 100 ppm 100 ppm Not
established
STEL 125 ppm Not 125 ppm 125 ppm Not
established established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
1,2,4-trimethylbenzene TWA 25 ppm Not 25 ppm 25 ppm Not
established established
STEL
Not Not Not 35 ppm Not
established established established established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
mesitylene TWA 25 ppm Not 25 ppm 25 ppm Not
established established
STEL
Not Not Not 35 ppm Not
established established established established
____________________________ ___________ ___________ ___________ ___________ ___________ ___________
Key to abbreviations
A = Acceptable Maximum Peak S = Potential skin absorption
ACGIH = American Conference of Governmental Industrial Hygienists. SR = Respiratory sensitization
C = Ceiling Limit SS = Skin sensitization
F = Fume TD = Total dust
IPEL = Internal Permissible Exposure Limit TLV = Threshold Limit Value
OSHA = Occupational Safety and Health Administration. TWA = Time Weighted Average
R = Respirable Z = OSHA 29CFR 1910.1200 Subpart Z - Toxic and Hazardous
Substances
Consult local authorities for acceptable exposure limits.
United States - Canada - Mexico Page: 4/9
Product code 97-53 Date of issue 5 December 2008 Version 7.02
Product name *LOW VOC AQUAPON PASTEL BASE "A"
8. Exposure controls/personal protection
Recommended monitoring : If this product contains ingredients with exposure limits, personal, workplace atmosphere
or biological monitoring may be required to determine the effectiveness of the ventilation
procedures
or other control measures and/or the necessity to use respiratory protective equipment.
Engineering measures : Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas, vapor
or dust concentrations below any lower explosive limits. Use explosion-proof ventilation
equipment.
Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period. Appropriate
techniques should be used to remove potentially contaminated clothing. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety showers
are close to the workstation location.
Personal protection
Eyes : Chemical splash goggles.
Hands : Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary.
Gloves : nitrile, neoprene
Respiratory : If workers are exposed to concentrations above the exposure limit, they must use
appropriate, certified respirators. Use a properly fitted, air-purifying or air-fed respirator
complying with an approved standard if a risk assessment indicates this is necessary.
Respirator selection must be based on known or anticipated exposure levels, the
hazards of the product and the safe working limits of the selected respirator.
Skin : Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before handling
this product.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure they
comply with the requirements of environmental protection legislation. In some cases,
controls
fume scrubbers, filters or engineering modifications to the process equipment will be
necessary to reduce emissions to acceptable levels.
9. Physical and chemical properties
Physical state : Liquid.
Flash point : Closed cup: 15癈 (59癋)
Explosion limits : Lower: 1.8%
Color : Not available.
Odor : Not available.
pH : Not available.
Boiling/condensation point : >37.78癈 (>100癋)
Melting/freezing point : Not available.
Specific gravity : 1.25
Density ( lbs / gal ) : 10.43
Vapor pressure : 2.6 kPa (19.4 mm Hg)
Vapor density : Not available.
Volatility : 46% (v/v), 30.82% (w/w)
Odor threshold : Not available.
Evaporation rate : 144 (Butyl acetate. = 1)
Octanol/water partition : Not available.
coefficient
United States - Canada - Mexico Page: 5/9
Product code 97-53 Date of issue 5 December 2008 Version 7.02
Product name *LOW VOC AQUAPON PASTEL BASE "A"
9. Physical and chemical properties
% Solid. (w/w) : 69.18
10 . Stability and reactivity
Stability : Stable under recommended storage and handling conditions (see section 7).
Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.
Materials to avoid : Reactive or incompatible with the following materials:,water,acids,oxidizing
materials,strong alkalis
Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
products
Hazardous polymerization : Under normal conditions of storage and use, hazardous polymerization will not occur.
11 . Toxicological information
Acute toxicity
Product/ingredient name Result Species Dose Exposure
titanium dioxide LD50 Oral Rat >10 g/kg -
propan-2-ol LD50 Oral Rat 4.396 g/kg -
LD50 Dermal Rabbit 12800 mg/kg -
LC50 Inhalation Rat 72600 mg/m3 4 hours
Vapor
xylene (mixture of o-, m-, p-isomers) LD50 Oral Rat 4.3 g/kg -
LD50 Dermal Rabbit >1.7 g/kg -
LC50 Inhalation Rat 5000 ppm 4 hours
1-methoxy-2-propanol LD50 Oral Rat 5.2 g/kg -
LD50 Dermal Rabbit 13 g/kg -
2-(propyloxy)ethanol LD50 Oral Rat 3089 mg/kg -
LD50 Dermal Rabbit 1.337 g/kg -
ethylbenzene LD50 Oral Rat 3.5 g/kg -
LD50 Dermal Rabbit >5000 mg/kg -
LC50 Inhalation Rat 4000 ppm 4 hours
Vapor
solvent naphtha (petroleum), light arom. LD50 Oral Rat 8400 mg/kg -
LD50 Dermal Rabbit 3.48 g/kg -
1,2,4-trimethylbenzene LD50 Oral Rat 5 gm/kg -
LC50 Inhalation Rat 18000 mg/m3 4 hours
mesitylene LD50 Oral Rat 5000 mg/kg -
LC50 Inhalation Rat 24000 mg/m3 4 hours
Conclusion/Summary : Not available.
Chronic toxicity
Conclusion/Summary : Not available.
Defatting irritant? : Prolonged or repeated contact can defat the skin and lead to irritation, cracking and/or
dermatitis.
Target organs : Contains material which causes damage to the following organs: blood, kidneys, liver,
brain, gastrointestinal tract, upper respiratory tract, skin, central nervous system (CNS),
eye, lens or cornea.
Contains material which may cause damage to the following organs: lungs, heart.
Carcinogenicity
Conclusion/Summary : Not available.
Carcinogenicity : Contains material which may cause cancer, based on animal data. Risk of cancer
depends on duration and level of exposure.
Classification
Product/ingredient name ACGIH IARC EPA NIOSH NTP OSHA
United States - Canada - Mexico Page: 6/9
Product code 97-53 Date of issue 5 December 2008 Version 7.02
Product name *LOW VOC AQUAPON PASTEL BASE "A"
11 . Toxicological information
titanium dioxide A4 2B - - - -
propan-2-ol A4 3 - - - -
xylene (mixture of o-, m-, p-isomers) A4 3 - - - -
silicon dioxide - 3 - - - -
ethylbenzene A3 2B - - - -
Mutagenicity
Conclusion/Summary : Not available.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity
Conclusion/Summary : Not available.
Teratogenicity : No known significant effects or critical hazards.
Reproductive toxicity
Conclusion/Summary : Not available.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.
12 . Ecological information
Environmental effects : No known significant effects or critical hazards.
Aquatic ecotoxicity
Product/ingredient Result Species Exposure
name
titanium dioxide Acute LC50 5.5 ppm Fresh water Daphnia - Water flea - Daphnia 48 hours
magna
_________________________________ ________________________________ __________
Chronic NOEC 1 ppm Fresh water Daphnia - Water flea - Daphnia 48 hours
magna
______________________ _________________________________ ________________________________ __________
propan-2-ol Acute LC50 >1400000 ug/L Fish - Bluegill - Lepomis macrochirus 96 hours
______________________ _________________________________ ________________________________ __________
xylene (mixture of o-, m-, Acute LC50 3300 to 4093 ug/L Fresh Fish - Rainbow trout,donaldson trout - 96 hours
p-isomers) water Oncorhynchus mykiss
______________________ _________________________________ ________________________________ __________
ethylbenzene Acute LC50 4200 ug/L Fresh water Fish - Rainbow trout,donaldson trout - 96 hours
Oncorhynchus mykiss
_________________________________ ________________________________ __________
Acute LC50 5100 to 5700 ug/L Marine Fish - Atlantic silverside - Menidia 96 hours
water menidia
_________________________________ ________________________________ __________
Acute EC50 2930 to 4400 ug/L Fresh Daphnia - Water flea - Daphnia 48 hours
water magna
_________________________________ ________________________________ __________
Chronic NOEC 3300 ug/L Marine water Fish - Atlantic silverside - Menidia 96 hours
menidia
______________________ _________________________________ ________________________________ __________
1,2,4-trimethylbenzene Acute LC50 7720 to 8280 ug/L Fresh Fish - Fathead minnow - Pimephales 96 hours
water promelas
______________________ _________________________________ ________________________________ __________
United States - Canada - Mexico Page: 7/9
Product code 97-53 Date of issue 5 December 2008 Version 7.02
Product name *LOW VOC AQUAPON PASTEL BASE "A"
13 . Disposal considerations
Waste disposal : The generation of waste should be avoided or minimized wherever possible. Empty
containers or liners may retain some product residues. This material and its container
must be disposed of in a safe way. Dispose of surplus and non-recyclable products via
a licensed waste disposal contractor. Disposal of this product, solutions and any by-
products should at all times comply with the requirements of environmental protection
and waste disposal legislation and any regional local authority requirements. Avoid
dispersal of spilled material and runoff and contact with soil, waterways, drains and
sewers.
Empty containers or liners may retain some product residues. This material and its
container must be disposed of in a safe way.
Disposal should be in accordance with applicable regional, national and local laws and regulations.
Refer to Section 7: HANDLING AND STORAGE and Section 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
for additional handling information and protection of employees. Section 6. Accidental release measures
14 . Transport information
Regulation UN number Proper shipping name Classes PG* Additional information
UN 1263 Paint 3 II -
IMDG 1263 Paint 3 II -
DOT 1263 Paint 3 II -
Reportable quantity RQ : CERCLA: Hazardous substances.: xylene (mixture of o-, m-, p-isomers): 100 lbs. (45.4 kg); 2-
(propyloxy)ethanol; ethylbenzene: 1000 lbs. (454 kg);
15 . Regulatory information
United States inventory (TSCA 8b) : All components are listed or exempted.
Australia inventory (AICS) : All components are listed or exempted.
Canada inventory : All components are listed or exempted.
China inventory (IECSC) : All components are listed or exempted.
Europe inventory : All components are listed or exempted.
Japan inventory (ENCS) : At least one component is not listed.
Korea inventory (KECI) : All components are listed or exempted.
New Zealand : Not determined.
Philippines inventory (PICCS) : At least one component is not listed.
United States
U.S. Federal regulations : TSCA 12(b) annual export notification: No products were found.
TSCA 12(b) one-time export: No products were found.
SARA 302/304/311/312 extremely hazardous substances: No products were found.
SARA 302/304 emergency planning and notification: No products were found.
SARA 302/304/311/312 hazardous chemicals: xylene (mixture of o-, m-, p-isomers);
titanium dioxide; aluminium hydroxide; propan-2-ol; 1-methoxy-2-propanol; ethylbenzene
SARA 311/312 MSDS distribution - chemical inventory - hazard identification:
xylene (mixture of o-, m-, p-isomers): Fire hazard, Immediate (acute) health hazard,
Delayed (chronic) health hazard; titanium dioxide: Immediate (acute) health hazard;
aluminium hydroxide: Immediate (acute) health hazard; propan-2-ol: Fire hazard,
Immediate (acute) health hazard, Delayed (chronic) health hazard; 1-methoxy-2-
propanol: Fire hazard, Immediate (acute) health hazard, Delayed (chronic) health
hazard; ethylbenzene: Fire hazard, Immediate (acute) health hazard, Delayed (chronic)
health hazard
CERCLA: Hazardous substances.: xylene (mixture of o-, m-, p-isomers): 100 lbs. (45.4
kg); 2-(propyloxy)ethanol; ethylbenzene: 1000 lbs. (454 kg);
United States - Canada - Mexico Page: 8/9
Product code 97-53 Date of issue 5 December 2008 Version 7.02
Product name *LOW VOC AQUAPON PASTEL BASE "A"
15 . Regulatory information
SARA 313 Product name CAS number Concentration
Form R - Reporting : propan-2-ol 67-63-0 7 - 13
requirements xylene (mixture of o-, m-, p-isomers) 1330-20-7 3-7
2-(propyloxy)ethanol 2807-30-9 1-5
ethylbenzene 100-41-4 0.5 - 1.5
California Prop. 65
WARNING: This product contains a chemical known to the State of California to cause cancer.
Canada
WHMIS (Canada) : Class B-2: Flammable liquid with a flash point lower than 37.8癈 (100癋). Class D-1B:
Material causing immediate and serious toxic effects (Toxic). Class D-2A: Material
causing other toxic effects (Very toxic).
Mexico
Classification
Flammability : 3 Health : 3 Reactivity : 0
16 . Other information
Hazardous Material Information System (U.S.A.)
Health : 3 * Flammability : 3 Physical hazards : 0
Caution: HMIS?ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks Although HMIS?ratings are not required on MSDSs under 29 CFR
1910.1200, the preparer may choose to provide them. HMIS?ratings are to be used with a fully implemented
HMIS?program. HMIS?is a registered mark of the National Paint & Coatings Association (NPCA). HMIS?br>
materials may be purchased exclusively from J. J. Keller (800) 327-6868.
The customer is responsible for determining the PPE code for this material.
National Fire Protection Association (U.S.A.)
Health : 3 Flammability : 3 Instability : 0
Date of previous issue : No previous validation.
Organization that prepared : EHS
the MSDS
Indicates information that has changed from previously issued version.
Disclaimer
The information contained in this data sheet is based on present scientific and technical knowledge. The purpose of this
information is to draw attention to the health and safety aspects concerning the products supplied by PPG, and to
recommend precautionary measures for the storage and handling of the products. No warranty or guarantee is given in
respect of the properties of the products. No liability can be accepted for any failure to observe the precautionary measures
described in this data sheet or for any misuse of the products.
United States - Canada - Mexico Page: 9/9
|