CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 1 of 12
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME
CATALYST FN (WINTER)
SYNONYMS
urea formaldehyde adhesive catalyst Syntec
resin hardener filler
PRODUCT USE
Urea formaldehyde adhesive catalyst/filler
SUPPLIER
Company: AV Syntec Pty Ltd Company: AV Syntec Pty Ltd
Address: Address:
30 Futura Road 15-21 Argon Street
Keysborough Carole Park
VIC, 3173 QLD, 4300
AUS AUS
Telephone: +61 3 9798 4944 Telephone: +61 7 3271 3411
Emergency Tel: +1800 039 008 Emergency Tel: +1800 039 008
Emergency Tel: +61 3 9573 3112 Emergency Tel: +61 3 9573 3112
Fax: 03 9798 5877 Fax: 07 3271 1852
HAZARD RATINGS
Flammability
Toxicity
Body Contact
Reactivity
Chronic
SCALE: Min/Nil=0 Low=1 Moderate=2 High=3 Extreme=4
Section 2 - HAZARDS IDENTIFICATION
STATEMENT OF HAZARDOUS NATURE
HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS.
CONSIDERED A HAZARDOUS SUBSTANCE ACCORDING TO DIRECTIVE
1999/45/EC AND ITS AMENDMENTS.
CONSIDERED A HAZARDOUS SUBSTANCE ACCORDING TO OSHA 29 CFR
1910.1200.
According to the Criteria of NOHSC, and the ADG Code.
POISONS SCHEDULE
None
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 2 of 12
Section 2 - HAZARDS IDENTIFICATION
RISK
Harmful if swallowed.
Irritating to eyes.
May cause CANCER.
Possible respiratory and skin sensitiser*.
* (limited evidence).
SAFETY
Avoid exposure - obtain special instructions before use.
Take off immediately all contaminated clothing.
In case of contact with eyes, rinse with plenty of water and contact Doctor or
Poisons Information Centre.
If you feel unwell contact Doctor or Poisons Information Centre. (Show the label
if possible).
Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS
NAME CAS RN %
wood dust Not avail. 30-60
macadamia nutshell flour Not avail. 30-60
ammonium chloride 12125-02-9 10-30
filler, unregulated <1
NOTE: Manufacturer has supplied full ingredient
information to allow CHEMWATCH assessment.
Section 4 - FIRST AID MEASURES
SWALLOWED
If swallowed do NOT induce vomiting.
If vomiting occurs, lean patient forward or place on left side (head-down
position, if possible) to maintain open airway and prevent aspiration.
Observe the patient carefully.
Never give liquid to a person showing signs of being sleepy or with reduced
awareness; i.e. becoming unconscious.
Give water to rinse out mouth, then provide liquid slowly and as much as
casualty can comfortably drink.
Seek medical advice.
EYE
If this product comes in contact with the eyes:
Wash out immediately with fresh running water.
Ensure complete irrigation of the eye by keeping eyelids apart and away from
eye and moving the eyelids by occasionally lifting the upper and lower lids.
If pain persists or recurs seek medical attention.
Removal of contact lenses after an eye injury should only be undertaken by
skilled personnel.
SKIN
If skin contact occurs:
Immediately remove all contaminated clothing, including footwear
Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
INHALED
If fumes or combustion products are inhaled remove from contaminated area.
Lay patient down. Keep warm and rested.
Prostheses such as false teeth, which may block airway, should be removed,
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 3 of 12
Section 4 - FIRST AID MEASURES
where possible, prior to initiating first aid procedures.
Apply artificial respiration if not breathing, preferably with a demand valve
resuscitator, bag-valve mask device, or pocket mask as trained. Perform CPR if
necessary.
Transport to hospital, or doctor.
NOTES TO PHYSICIAN
Treat symptomatically.
Section 5 - FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
There is no restriction on the type of extinguisher which may be used.
Use extinguishing media suitable for surrounding area
FIRE FIGHTING
Alert Fire Brigade and tell them location and nature of hazard.
Wear breathing apparatus plus protective gloves for fire only.
Prevent, by any means available, spillage from entering drains or water
courses.
Use fire fighting procedures suitable for surrounding area.
DO NOT approach containers suspected to be hot.
Cool fire exposed containers with water spray from a protected location.
If safe to do so, remove containers from path of fire.
Equipment should be thoroughly decontaminated after use.
FIRE/EXPLOSION HAZARD
Non combustible.
Not considered to be a significant fire risk, however containers may burn.
In a fire may decompose on heating and produce toxic / corrosive fumes.
Decomposes on heating and produces toxic fumes of hydrogen chloride , ammonia ,
nitrogen oxides (NOx) , carbon monoxide (CO) and aldehydes
Avoid creating dust - may present dust explosion hazard. Dry dust can be
electrostatically charged by turbulence, pneumatic transport, pouring, in
exhaust ducts and during transport. Build-up of electrostatic charge may be
prevented by grounding.
FIRE INCOMPATIBILITY
Avoid contamination with strong oxidising agents as ignition may result
HAZCHEM
None
Personal Protective Equipment
PERSONAL PROTECTION EQUIPMENT
Gas tight chemical resistant suit.
Limit exposure duration to 1 BA set - 30 mins.
Section 6 - ACCIDENTAL RELEASE MEASURES
EMERGENCY PROCEDURES
MINOR SPILLS
Clean up all spills immediately.
Avoid contact with skin and eyes.
Wear impervious gloves and safety glasses.
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 4 of 12
Section 6 - ACCIDENTAL RELEASE MEASURES
Use dry clean up procedures and avoid generating dust.
Sweep up or
Vacuum up (consider explosion-proof machines designed to be grounded during
storage and use).
Place spilled material in clean, dry, sealable, labelled container.
MAJOR SPILLS
Remove all ignition sources.
Clear area of personnel and move upwind.
Alert Fire Brigade and tell them location and nature of hazard.
Control personal contact by using protective equipment and dust respirator.
Prevent spillage from entering drains, sewers or water courses.
Avoid generating dust.
Sweep, shovel up. Recover product wherever possible.
Put residues in labelled plastic bags or other containers for disposal.
If contamination of drains or waterways occurs, advise emergency services.
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
Section 7 - HANDLING AND STORAGE
PROCEDURE FOR HANDLING
Limit all unnecessary personal contact.
Wear protective clothing when risk of exposure occurs.
Use in a well-ventilated area.
Avoid contact with incompatible materials.
When handling, DO NOT eat, drink or smoke.
Keep containers securely sealed when not in use.
Avoid physical damage to containers.
Always wash hands with soap and water after handling.
Work clothes should be laundered separately.
Use good occupational work practice.
Observe manufacturer's storing and handling recommendations.
Atmosphere should be regularly checked against established exposure standards
to ensure safe working conditions are maintained.
SUITABLE CONTAINER
Multi ply paper bag with sealed plastic liner or heavy gauge plastic bag
NOTE: Bags should be stacked, blocked, interlocked, and limited in height so
that they are stable and secure against sliding or collapse. Check that all
containers are clearly labelled and free from leaks. Packing as recommended by
manufacturer.
STORAGE INCOMPATIBILITY
Segregate from strong oxidisers , acids and alkalies
STORAGE REQUIREMENTS
Keep dry
Store in original containers.
Keep containers securely sealed.
Store in a cool, dry, well-ventilated area.
Store away from incompatible materials and foodstuff containers.
Protect containers against physical damage and check regularly for leaks.
Observe manufacturer's storing and handling recommendations.
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 5 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE CONTROLS
Source Material TWA TWA STEL STEL Peak Peak
ppm mg/m? ppm mg/m? ppm mg/m?br>
_________________________ ________________ _____ _____ _____ _____ _____ _____
Australian Exposure Ammonium 10 20
Standards chloride (fume)
No data available for wood dust as (CAS: Not avail) / (CAS: Not avail)
TLV TWA: 10 mg/m?(Value for particulate matter containing no asbestos and <1% crystalline
silica,Inhalable fraction) [ACGIH]
TLV TWA: 3 mg/m?(Value for particulate matter containing no asbestos and <1% crystalline
silica,Respirable fraction) [ACGIH]
Particulate (insoluble or poorly soluble *) Not Otherwise Specified (P.N.O.C)
TLV TWA: 10 mg/m?Inhalable particulate
TLV TWA: 3 mg/m?Respirable particulate
OEL-Sweden, United Kingdom: 10 mg/m?total dust, 5 mg/m?respirable dust
These "dusts" have little adverse effect on the lungs and do not produce toxic
effects or organic disease. Although there is no dust which does not evoke some
cellular response at sufficiently high concentrations, the cellular response
caused by P.N.O.C.s has the following characteristics:
the architecture of the air spaces remain intact,
scar tissue (collagen) is not synthesised to any degree,
tissue reaction is potentially reversible.
Extensive concentrations of P.N.O.C.s may:
seriously reduce visibility,
cause unpleasant deposits in the eyes, ears and nasal passages,
contribute to skin or mucous membrane injury by chemical or mechanical action,
per se, or by the rigorous skin cleansing procedures necessary for their
removal. [ACGIH]
This limit does not apply:
to brief exposures to higher concentrations
nor does it apply to those substances that may cause physiological impairment
at lower concentrations but for which a TLV has as yet to be determined.
This exposure standard applies to particles which
are insoluble or poorly soluble* in water or, preferably, in aqueous lung
fluid (if data is available) and
have a low toxicity (i.e.. are not cytotoxic, genotoxic, or otherwise
chemically reactive with lung tissue, and do not emit ionizing radiation, cause
immune sensitization, or cause toxic effects other than by inflammation or by a
mechanism of lung overload)
* Notice of intended change
EXPOSURE STANDARDS FOR MIXTURE
"Worst Case" computer-aided prediction of spray/ mist or fume/ dust components
and concentration:
Composite Exposure Standard for Mixture (TWA) :1.4085 mg/m?
Operations which produce a spray/mist or fume/dust, introduce particulates to
the breathing zone.
If the breathing zone concentration of ANY of the components listed below is
exceeded, "Worst Case" considerations deem the individual to be overexposed.
Component Breathing Zone ppm Breathing Zone mg/m?Mixture Conc (%)
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 6 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Component Breathing Zone Mixture Conc
(mg/m? (%)
wood dust 0.8451 60.0
macadamia nutshell flour 0.4225 30.0
ammonium chloride 0.1408 10.0
INGREDIENT DATA
WOOD DUST:
certain hard woods as beech & oak:
TLV TWA: 1 mg/m?A1
WARNING: This substance has been classified by the ACGIH as A1 CONFIRMED HUMAN
CARCINOGEN
ES TWA: 1 mg/m?(Sensitiser) (Under review)
soft wood:
TLV TWA: 5 mg/m? STEL: 10 mg/m?br>
ES TWA: 5 mg/m? STEL: 10 mg/m?(Sensitiser) (Under review)
Wood dusts produce dermatitis and an increased risk of upper respiratory
disease. Epidemiological studies in furniture workers show an increased risk of
lung, tongue, pharynx and nasal cancer. An excess risk of leukaemia amongst
millwrights probably is associated with exposure to various components used in
wood preservation.
Impairment of nasal mucociliary function may occur below 5 mg/m?and may be
important in the development of nasal adenocarcinoma amongst furniture workers
exposed to hardwoods.
Certain exotic hardwoods contain alkaloids which may produce headache, anorexia,
nausea, bradycardia and dyspnoea.
The softwood TLV-TWA reflects the apparent low risk for upper respiratory tract
involvement amongst workers in the building industry. A separate TLV-TWA, for
hard woods, is based on impaired nasal mucociliary function reported to
contribute to nasal adenocarcinoma and related hyperplasia found in furniture
workers.
TRK: 2 mg/m?br>
(measured as inhalable fraction of the aerosol)
The technical exposure limit, TRK (Technische Richtkonzentrationen), defines the
airborne concentration of named carcinogenic materials which is the minimum
possible given the state of current technologies. TRK values are assigned only
for materials for which there is no current MAK (German exposure standard).
Observance of the TRK value is intended to reduce the risk of adverse effects on
health but does NOT completely eliminate it. Since no threshold doses can be
determined for carcinogens, health considerations require that the exposure
limits be kept as far as possible below the TRK and that the TRK value be
gradually reduced. The limitation of exposure peaks is regulated as follows;
Short-term exposure limit: 5 x TRK
Short-term exposure duration: 15 min/average
Frequency per work shift: 5 times
Interval: 1 hour
Report No. 35 1999, Deutsche Forschungsgemeinschaft.
MACADAMIA NUTSHELL FLOUR:
TLV TWA: 10 mg/m?(Value for particulate matter containing no asbestos and <1% crystalline
silica,Inhalable fraction) [ACGIH]
TLV TWA: 3 mg/m?(Value for particulate matter containing no asbestos and <1% crystalline
silica,Respirable fraction) [ACGIH]
Dusts not otherwise classified, as inspirable dust;
ES TWA: 10 mg/m?br>
Particulate (insoluble or poorly soluble *) Not Otherwise Specified (P.N.O.C)
TLV TWA: 10 mg/m?Inhalable particulate
TLV TWA: 3 mg/m?Respirable particulate
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 7 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
OEL-Sweden, United Kingdom: 10 mg/m?total dust, 5 mg/m?respirable dust
These "dusts" have little adverse effect on the lungs and do not produce toxic
effects or organic disease. Although there is no dust which does not evoke some
cellular response at sufficiently high concentrations, the cellular response
caused by P.N.O.C.s has the following characteristics:
?the architecture of the air spaces remain intact,
?scar tissue (collagen) is not synthesised to any degree,
?tissue reaction is potentially reversible.
Extensive concentrations of P.N.O.C.s may:
?seriously reduce visibility,
?cause unpleasant deposits in the eyes, ears and nasal passages,
?contribute to skin or mucous membrane injury by chemical or mechanical action,
per se, or by the rigorous skin cleansing procedures necessary for their
removal. [ACGIH]
This limit does not apply:
?to brief exposures to higher concentrations
?nor does it apply to those substances that may cause physiological impairment
at lower concentrations but for which a TLV has as yet to be determined.
This exposure standard applies to particles which
?are insoluble or poorly soluble* in water or, preferably, in aqueous lung
fluid (if data is available) and
?have a low toxicity (i.e.. are not cytotoxic, genotoxic, or otherwise
chemically reactive with lung tissue, and do not emit ionizing radiation, cause
immune sensitization, or cause toxic effects other than by inflammation or by a
mechanism of lung overload)
* Notice of intended change
AMMONIUM CHLORIDE:
TLV TWA: 10 mg/m?[ACGIH]
TLV STEL: 20 mg/m?[ACGIH]
as fume
TLV* TWA: 10 mg/m? STEL: 20 mg/m?br>
ES* TWA: 10 mg/m? STEL: 20 mg/m?br>
OES* TWA: 10 mg/m? STEL: 20 mg/m?br>
Based on moderate inhalation the TLV-TWA is thought to be protective
against irritation of the respiratory tract.
as dusts not otherwise classified
TLV TWA: 10 mg/m?total dust
ES TWA: 10 mg/m?inspirable dust
PERSONAL PROTECTION
EYE
Safety glasses with side shields; or as required,
Chemical goggles.
Contact lenses pose a special hazard; soft lenses may absorb irritants and all
lenses concentrate them.
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 8 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
HANDS/FEET
Wear chemical protective gloves, eg. PVC.
Wear safety footwear.
OTHER
Overalls.
Eyewash unit.
RESPIRATOR
Protection Factor Half-Face Full-Face Powered Air
Respirator Respirator Respirator
10 x ES P2 - -
Air-line* - -
50 x ES Air-line** P2 PAPR-P2
- Air-line* -
100 x ES - Air-line** PAPR-P3
* - Negative pressure demand ** - Continuous flow
The local concentration of material, quantity and conditions of use determine
the type of personal protective equipment required. For further information
consult site specific CHEMWATCH data (if available), or your Occupational
Health and Safety Advisor.
ENGINEERING CONTROLS
Local exhaust ventilation is required where solids are handled as powders or
crystals; even when particulates are relatively large, a certain proportion will
be powdered by mutual friction.
Exhaust ventilation should be designed to prevent accumulation and
recirculation of particulates in the workplace.
If in spite of local exhaust an adverse concentration of the substance in air
could occur, respiratory protection should be considered. Such protection might
consist of:
(a): particle dust respirators, if necessary, combined with an absorption
cartridge;
(b): filter respirators with absorption cartridge or canister of the right type;
(c): fresh-air hoods or masks
Build-up of electrostatic charge on the dust particle, may be prevented by
bonding and grounding.
Powder handling equipment such as dust collectors, dryers and mills may
require additional protection measures such as explosion venting.
Air contaminants generated in the workplace possess varying "escape" velocities
which, in turn, determine the "capture velocities" of fresh circulating air
required to efficiently remove the contaminant.
Type of Contaminant: Air Speed:
direct spray, spray painting in shallow 1-2.5 m/s (200-500 f/min.)
booths, drum filling, conveyer loading,
crusher dusts, gas discharge (active
generation into zone of rapid air
motion)
grinding, abrasive blasting, tumbling, 2.5-10 m/s (500-2000 f/min.)
high speed wheel generated dusts
(released at high initial velocity into
zone of very high rapid air motion).
Within each range the appropriate value depends on:
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 9 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Lower end of the range Upper end of the range
1: Room air currents minimal or 1: Disturbing room air currents
favourable to capture
2: Contaminants of low toxicity or of 2: Contaminants of high toxicity
nuisance value only
3: Intermittent, low production. 3: High production, heavy use
4: Large hood or large air mass in 4: Small hood-local control only
motion
Simple theory shows that air velocity falls rapidly with distance away from the
opening of a simple extraction pipe. Velocity generally decreases with the
square of distance from the extraction point (in simple cases). Therefore the
air speed at the extraction point should be adjusted, accordingly, after
reference to distance from the contaminating source. The air velocity at the
extraction fan, for example, should be a minimum of 4-10 m/s (800-2000 f/min)
for extraction of crusher dusts generated 2 metres distant from the extraction
point. Other mechanical considerations, producing performance deficits within
the extraction apparatus, make it essential that theoretical air velocities are
multiplied by factors of 10 or more when extraction systems are installed or
used.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE
Brown powder with low odour. Slightly soluble in water.
PHYSICAL PROPERTIES
Solid.
Does not mix with water.
Molecular Weight: Not applicable. Boiling Range (?Not available.
C):
Melting Range (?Not available.
C): Specific Gravity (water=1): Not available.
Solubility in water (g/L): Partly miscible pH (as supplied): Not applicable
pH (1% solution): Not applicable Vapour Pressure (kPa): Not available.
Volatile Component (%vol): Not available. Evaporation Rate: Not applicable
Relative Vapour Density (air=1): Not available. Flash Point (?Not applicable
C):
Lower Explosive Limit (%): Not applicable Upper Explosive Limit (%): Not applicable
Autoignition Temp (?Not applicable
C): Decomposition Temp (?Not available.
C):
State: Divided solid
Section 10 - CHEMICAL STABILITY AND REACTIVITY INFORMATION
CONDITIONS CONTRIBUTING TO INSTABILITY
Presence of incompatible materials.
Product is considered stable.
Hazardous polymerisation will not occur.
Section 11 - TOXICOLOGICAL INFORMATION
POTENTIAL HEALTH EFFECTS
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 10 of 12
Section 11 - TOXICOLOGICAL INFORMATION
ACUTE HEALTH EFFECTS
SWALLOWED
Considered an unlikely route of entry in commercial/industrial environments
The solid/dust is discomforting to the gastro-intestinal tract and may be
harmful if swallowed
Ingestion may result in nausea, abdominal irritation, pain and vomiting
EYE
The solid/dust is mildly discomforting to the eyes and is capable of causing a
mild, temporary redness of the conjunctiva (similar to wind-burn), temporary
impairment of vision and/ or other transient eye damage/ ulceration
The material may produce severe irritation to the eye causing pronounced
inflammation. Repeated or prolonged exposure to irritants may produce
conjunctivitis.
SKIN
The material may be discomforting to the skin if exposure is prolonged and is
capable of causing skin reactions which may lead to dermatitis from repeated
exposures over long periods
INHALED
The dust is discomforting to the upper respiratory tract and may be harmful if
inhaled
CHRONIC HEALTH EFFECTS
Principal routes of exposure are by accidental skin and eye contact and inhalation of
generated dusts. Sensitisation reactions may appear suddenly after repeated symptom free
exposures One ingredient of the product has caused skin sensitisation reactions, shown as
localised reddening and hives, or may produce respiratory sensitisation characterised by
asthma-like symptoms and runny nose.
Catalyst FN (Winter)
Not available. Refer to individual constituents.
unless otherwise specified data extracted from RTECS - Register of Toxic Effects
of Chemical Substances
WOOD DUST:
No significant acute toxicological data identified in literature search.
CAUTION : Inhalation of wood dust by workers in the furniture industry has
been related to nasal cancer. [ILO Encyclopaedia]
WARNING: This substance has been classified by the IARC as Group 1: CARCINOGENIC
TO HUMANS.
Tenth Annual Report on Carcinogens: Substance known to be Carcinogenic
[National Toxicology Program: U.S. Dep. of Health and Human Services 2002]
MACADAMIA NUTSHELL FLOUR:
No significant acute toxicological data identified in literature search.
AMMONIUM CHLORIDE:
TOXICITY IRRITATION
Oral (rat) LD50: 1650 mg/kg Eye (rabbit): 500 mg/24h SEVERE
SEVERE Eye (rabbit): 100 mg SEVERE
Section 12 - ECOLOGICAL INFORMATION
No data for Catalyst FN (Winter).
Refer to data for ingredients, which follows:
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 11 of 12
Section 12 - ECOLOGICAL INFORMATION
WOOD DUST:
No data for wood dust.
MACADAMIA NUTSHELL FLOUR:
No data for macadamia nutshell flour.
AMMONIUM CHLORIDE:
Hazardous Air Pollutant: No
Daphnia magna EC50 (48hr.) (mg/l): 161
Toxicity Fish: TLm(96)50mg/L
Section 13 - DISPOSAL CONSIDERATIONS
Recycle wherever possible or consult manufacturer for recycling options.
Consult State Land Waste Management Authority for disposal.
Bury residue in an authorised landfill.
Recycle containers if possible, or dispose of in an authorised landfill.
Section 14 - TRANSPORTATION INFORMATION
Shipping Name:
NONE
Dangerous Goods Class: None
UN/NA Number: None
ADR Number: None
Packing Group: None
Labels Required:
Additional Shipping Information:
International Transport Regulations:
IMO: None
HAZCHEM
None
Section 15 - REGULATORY INFORMATION
POISONS SCHEDULE
None
REGULATIONS
ammonium chloride (CAS: 12125-02-9) is found on the following regulatory lists:
Australian Inventory of Chemical Substances (AICS)
Section 16 - OTHER INFORMATION
This document is copyright. Apart from any fair dealing for the purposes of
private study, research, review or criticism, as permitted under the Copyright
Act, no part may be reproduced by any process without written permission from
CHEMWATCH. TEL (+61 3) 9572 4700.
Issue Date: Thu 1-Mar-2001
continued...
CATALYST FN (WINTER)
ChemWatch Material Safety Data Sheet (REVIEW) CHEMWATCH 5036-09
Issue Date: Thu 1-Mar-2001 CD 2005/1 Page 12 of 12
Section 16 - OTHER INFORMATION
Print Date: Mon 30-May-2005
|