MS-880G BASE COMPONENT
Document # 3260 Page 1 of 2
SECTION 1: PRODUCT IDENTIFICATION AND USE
MFG'S NAME: AMERICAN SAFETY TECHNOLOGIES INC. TRADE NAME: MS-880G
565 Eagle Rock Ave. BASE COMPONENT
Roseland, New Jersey 07068
(973) 403-2600 CHEMICAL FAMILY: EPOXY
Dot Shipping Classification (49CFR 172.101): Paint, Combustible Liquid, UN1263,III HMIS RATING:
Transportation Emergency Number (CHEMTREC): 1-800-424-9300 Health =2
Mfg's Dunn's No: 002-171-213 Flammability =2
Reactivity =0
COMMER'L & GOV'T ENTITY (CAGE) CODE: 88444
NATIONAL STOCK NO: SPEC: (Type, Grade, or Class) CONTRACT OR ORDER NO.
8010-01-397-3802 MIL-PRF-24667B (Navy) Type III Comp G
8010-01-397-3806
PREPARED BY: J. Hermele DATE: 08/06/98 REVISION: 1
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
INGREDIENTS CAS No % WT. OSHA ACGIH OTHER
Epoxy Resin 25068-38-6 20-30% N.E. N.E. LD50RAT>5g/Kg(Oral)
Polyglycol Epoxy Resin 41638-13-5 < 3% N.E. N.E.
Alumino-Silcate Mineral 37244-96-5 10-20% 10mg/m3 dust 10mg/m3 dust
Brominated Diphenyl Ether 1163-19-5 15-20% 10mg/m3 dust 10mg/m3 dust
Aluminum Oxide 1344-28-1 40-50% 15mg/m3 dust 10mg/m3 dust
Propelyne Glycol Ether 1569-02-4 10-15% N.E. N.E.
* Contains less than 0.1% Crystalline Silica
(N.E. = Not Established)
SECTION 313 SUPPLIER INFORMATION: THIS PRODUCT CONTAINS THE FOLLOWING CHEMICALS SUBJECT TO THE
REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT OF
1986 AND OF 40 CFR 372. THIS INFORMATION MUST BE INCLUDED ON THE MSDS COPIED AND DISTRIBUTED FOR THIS
MATERIAL.
FLASH POINT: >101F/38C SETA FLAMMABLE LIMITS: LEL UEL
1.62 11.8
EXTINGUISHING MEDIA: Dry Chemical and Chemical Foam.
SPECIAL FIRE FIGHTING PROCEDURES: Remove all ignition sources. Wear self-contained breathing
apparatus and complete personal protective equipment where potential for exposure to vapors or products of
combustion exists.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS: Closed containers may rupture (due to build up of pressure)
when exposed to extreme heat. Decomposition and combustion products may be toxic.
MS-880G BASE COMPONENT
Page 2 of 2
SECTION 5: HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation/Skin/Ingestion
HEALTH HAZARDS (ACUTE AND CHRONIC)
Eyes: Irritant. Aggregate may cause injury.
Skin: May cause moderate irritation and sensitization.
Inhalation: Vapors may cause headaches, nausea, dizziness and respiratory irritation.
Ingestion: No specific information available. Contains materials that may be slightly toxic.
CONDITIONS AGGRAVATED BY EXPOSURE: Allergy, eczema and other skin conditions.
CARCINOGENIC DATA: Not on NTP, IARC or OSHA Lists.
OVEREXPOSURE EFFECTS: Irritation, sensitization and dermatitis.
EMERGENCY AND FIRST AID PROCEDURES:
Eyes: Flush with large quantities of water for at least 15 minutes. Get medical attention.
Skin: Remove contaminated clothing. Wash contact area with mild soap and water for 15
minutes.
Inhalation: Remove to fresh air. If breathing has stopped administer artificial respiration and seek
medical attention.
Ingestion: Do not induce vomiting (contains solvent). Get medical attention.
SECTION 6: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Excessive Heat
INCOMPATIBILITY (Materials to Avoid): Strong Oxidizing Agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Monoxide, Carbon Dioxide and Aldehydes.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Eliminate all ignition sources.
Dike Spill. Absorb with inert material and collect for disposal. Flush contaminated area with water; prevent
washings from entering waterways.
WASTE DISPOSAL METHODS: This product, if disposed as shipped, meets EPA criteria of a hazardous
waste as specified in 40 CFR 261 on the basis of its ignitability. Dispose of in a licensed hazardous waste
facility in accordance with applicable laws.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: NIOSH/MSHA approved respirator with organic vapor cartridge if required.
VENTILATION: Explosion-proof mechanical ventilation and local exhaust are recommended. Mechanical
exhaust is not recommended as the sole means of controlling employee exposure.
PROTECTIVE GLOVES: Impervious gloves.
EYE PROTECTION: Chemical splash-proof goggles.
OTHER PROTECTIVE EQUIPMENT: In operations where contact may occur, coveralls, apron and
impervious foot covering are recommended.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Avoid all personal contact. Do not exceed
110癋/43癈 in storage area. Ground and bond metal containers for liquid transfer to avoid static sparks.
SECTION 9: SPECIAL / OTHER INSTRUCTIONS
* A safety shower and eye wash facility should be available to employees.
* Contaminated clothing should be removed immediately and thoroughly laundered before reuse.
MATERIAL SAFETY DATA SHEET
MS-880 HARDENER COMPONENT
Document #3280 Page 1 of 2
SECTION 1: PRODUCT IDENTIFICATION AND USE
TRADE NAME: MS-880
MFG'S NAME: ITW AMERICAN SAFETY TECHNOLOGIES
565 Eagle Rock Ave. HARDENER COMPONENT
Roseland, New Jersey 07068
(973) 403-2600 CHEMICAL FAMILY: AMINE COMPOUND
NATIONAL STOCK NO: SPEC: (Type, Grade, or Class) CONTRACT OR ORDER NO.
MIL-PRF-24667B (Navy) Type III; MIL-D-24613 Type 2 Class 2
PREPARED BY: J. Hermele DATE: 12/6/00 REVISION: 2
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
INGREDIENTS CAS NO. % VOL OSHA ACGIH OTHER
n-aminoethylpiperazine 140-31-8 <25% N.E. N.E.
methylendi(cyclohexylamine) 1761-71-3 <20% N.E. N.E.
nonylphenol 25154-52-3 <45% N.E. N.E.
The remaining components are trade secret.
(N.E. = Not Established)
SECTION 313 SUPPLIER INFORMATION: THIS PRODUCT CONTAINS THE FOLLOWING CHEMICALS SUBJECT TO THE
REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT OF
1986 AND OF 40 CFR 372. THIS INFORMATION MUST BE INCLUDED ON THE MSDS COPIED AND DISTRIBUTED FOR THIS
MATERIAL.
CHEMICAL NAME CAS NUMBER WEIGHT %
None
___________________________________________________________________ __________________
SECTION 3: PHYSICAL DATA
FLASH POINT: >230癋/110癈 SETA FLAMMABLE LIMITS: LEL UEL
N.E. N.E.
EXTINGUISHING MEDIA: Dry Chemical, Carbon Dioxide, Foam or Water.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self-contained breathing apparatus and complete personal
protective equipment where potential for exposure to vapors or products of combustion exists.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS: Decomposition and combustion products may be toxic.
MS-880 HARDENER COMPONENT
SECTION 5: HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation/Skin/Ingestion
HEALTH HAZARDS (ACUTE AND CHRONIC)
Eyes: Causes severe irritation or burns. May cause permanent visual impairment.
Skin: Causes severe irritation or burns. May be absorbed through skin in harmful amounts.
Inhalation: May cause nose and throat irritation.
Ingestion: May cause burns of mouth and throat. Contains material that may be slightly toxic.
CONDITIONS AGGRAVATED BY EXPOSURE: Allergy, eczema and other skin conditions.
CARCINOGENIC DATA: Not on NTP, IARC or OSHA Lists.
OVEREXPOSURE EFFECTS: Irritation, sensitization and dermatitis.
EMERGENCY AND FIRST AID PROCEDURES:
Eyes: Flush with large quantities of water for at least 15 minutes. Get medical attention.
Skin: Remove contaminated clothing. Wash contact area with mild soap and water for 15
minutes.
Inhalation: Remove to fresh air. If symptoms persist consult a physician.
Ingestion: Do not induce vomiting. If conscious, give large quantities of water to dilute.
Get medical attention.
SECTION 6: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Excessive Heat
INCOMPATIBILITY (Materials to Avoid): Strong Oxidizing Agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Monoxide, Carbon Dioxide, and Oxides of Nitrogen.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Dike Spill. Absorb with inert
material and collect for disposal. Flush contaminated area with dilute (5%) acetic acid and collect rinsate for
disposal.
WASTE DISPOSAL METHODS: This product, if disposed as shipped, is not a hazardous waste as specified
in 40 CFR 261. Consult State or local officials for proper disposal method.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: NIOSH/MSHA approved respirator with organic vapor cartridge if required.
VENTILATION: Local exhaust recommended. Mechanical ventilation is not recommended as the sole
means of controlling employee exposure.
PROTECTIVE GLOVES: Impervious rubber or plastic gloves.
EYE PROTECTION: Chemical splash-proof goggles.
OTHER PROTECTIVE EQUIPMENT: In operations where contact may occur, coveralls, apron and
impervious foot covering are recommended.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Avoid all personal contact. Do not exceed
110F/43C in storage area. Ground and bond metal containers for liquid transfer to avoid static sparks.
SECTION 9: SPECIAL / OTHER INSTRUCTIONS
* A safety shower and eye wash facility should be available to employees.
* Immediately remove and thoroughly launder contaminated clothing before reuse.