P.O. Box 1007, Katy, Texas 77492 Office: (281) 728-7280 Fax: (281) 391-5655
Advanced Epoxy Systems
MATERIAL SAFETY DATA SHEET
Section I ?IDENTITY INFORMATION
Identity (Tradename): AES-100 Flexible Roof Coating Part B
Product Type: Epoxy Solution
Date Revised: April 10, 2008
CHEMTREC Emergency Number 1-800-424-9300
Section II ?HAZARDOUS INGREDIENTS
Occupational Exposure Limits Vapor Pressure
Hazardous Components CAS # OSHA PEL ACGIH TLV OSHA STEL mm Hg @ Temp
Xylene 1330-20-7 100 PPM 50 PPM NE 6mm 68篎
Ethyl Benzene 100-41-4 100 PPM 100 PPM NE N/A
Trade Secret (Polyamide) NE NE NE N/A
Antimony Trioxide 1309-64-4 50 PPM NE NE N/A
Decabromodephenyl Oxide 1163-19-5 150 PPM 100 PPM NE N/A
Pigment (Non-Hazardous) 100 PPM 100 PPM 60 PPM N/A
Carcinogen Status: IARC: Not Reviewed, NTP: Not Reviewed, OSHA: Not Reviewed
Section III ?PHYSICAL DATA
Boiling Point: 282篎 (Solvent) SP. Gravity (H20=1): 1
Vapor Density: 3.7 Xylene (Air = 1) Evaporation Rate: .6 Xylene (Butyl Acetate =1)
% Volatile: 17% Solubility in water: Partial
Physical State: Liquid
Appearance and Odor:Amber Liquid, Aromatic Odor
Section IV ?FIRE AND EXPLOSION HAZARD DATA
Flash Point: 80篎-Closed Cup
Flammable Limits (LFL/UFL): 1/7 (Xylene)
Extinguishing Media: Carbon Dioxide, Foam, Dry Chemical, Water Spray
Special Fire Fighting Procedures: Use self-contained breathing apparatus.
Unusual Fire and Explosion Hazards: Decomposition and combustion products may be toxic.
Heating forms flammable vapors which may form
explosive mixtures with air.
www.advancedepoxysystems.com
MSDS: AES-100 Flexible Roof Coating Part B Page 2 of 3
Section V ?REACTIVITY DATA
Stability: Stable
Incompatibility: Strong oxidizing agents
Hazardous Polymerization: Will not occur
Conditions to Avoid: Excessive heat and open flames.
Hazardous Decomposition Products: Carbon Monoxide, Carbon Dioxide, Nitrogen Oxides,
Aldehydes, and unidentified organic compounds
Section VI ?TOXICOLOGICAL INFORMATION
Primary Routes of Exposure: Dermal, Inhalation
Acute Oral Effects (LD50): (Rat) 4,300mg/kg (xylene).
Sensitization: Potential sensitizer
Acute Dermal Toxicity (LD50): (Rabbit)>5,000mg/kg (Polyamide resin).
Skin Irritation: (Rabbit) Moderate irritant
Eye Irritation: (Rabbit) Severe irritant
Section VII ?FIRST AID MEASURES
Skin: Wipe away excess material with dry towel. Wash affected areas with plenty of water and soap for
several minutes. Remove contaminated clothing and shoes. Get medical attention if irritation
occurs. Discard or decontaminate clothing before re-use and destroy contaminated shoes.
Eyes: Immediately flush eyes with running water for at least 15 minutes. Hold eyelids apart to ensure
rinsing of the entire eye surface and lids with water. Get immediate medical attention. If physician
is not available, flush for an additional 15 minutes.
Ingestion: If swallowed, give at least 3-4 glasses of water, but do not induce vomiting. Contains organic
solvent. Do not give anything by mouth to an unconscious or convulsing person. Get medical
attention immediately!
Inhalation: Remove to fresh air. Get immediate medical attention if respiratory irritation develops of if
breathing becomes difficult.
Overexposure Effects: Overexposure to this material can cause skin, eye, and respiratory irritation and
allergic skin reaction. Inhalation of vapors from a component in this product cause central nervous
system depression, headache, dizziness, loss of balance, coughing, pulmonary edema and liver and
kidney damage. Insensitive individuals, cardiac arrhythmia, leading to death, may occur. A component in
the product has caused fetal damage following dermal/oral exposure to guinea pigs or rats.
Medical Conditions Aggravated by Exposure: allergy, eczema, or skin conditions.
Section VIII ?SPILL OR LEAK PROCEDURES
Accidental Release Procedures: Remove all sources of ignition. Provide explosion proof ventilation.
Take up on absorbent material. Shovel with non-sparking tools into closable container for disposal.
Wear protective equipment specified below. Thoroughly flush contaminated area with water.
Waste Disposal Methods: Dispose in accordance with federal, state, and local regulations.
Section IX ?EXPOSURE CONTROLS/PERSONAL PROTECTION
Ventilation: Explosion proof mechanical ventilation and local exhaust recommended.
Skin Protection: Wear impervious gloves
Eye Protection: Wear splash-proof chemical goggles or complete face shield.
Respiratory Protection: Organic chemical cartridge respirator, if needed.
Other protective Equipment: Wear appropriate equipment to prevent probability of exposure and
personal contact.
P.O. Box 1007, Katy, Texas 77492 Office: (281) 728-7280 Fax: (281) 391-5655
www.advancedepoxysystems.com
MSDS: AES-100 Flexible Roof Coating Part B Page 3 of 3
Section X ?HANDLING AND STORAGE PRECAUTIONS
Warning! May cause severe eye irritation. May cause sensitization. Avoid breathing mist or vapor. Do
not take internally. Use with adequate ventilation. Wear chemical splash goggles, impervious gloves,
and protective clothing when handling. Wash thoroughly after handling. Keep container closed when not
in use. Store in dry area in closed containers. For industrial use only. Flammable solution. Keep away
from heat, sparks, and open flame.
Section XI ?TRANSPORT INFORMATION
DOT:
Proper Shipping Name: Resin Solution Hazard Class: 3
ID Number: UN 1866 Packing Group: PG III
ERG Number: 127
Section XII ?OTHER INFORMATION
OSHA Status: This Material Safety Data Sheet (MSDS) has been prepared in
compliance with the federal OSHA Hazard Communication Standard 29 CFR
1910.1200. This product is considered to be a hazardous chemical under that
standard.
Disclaimer: The information and recommendations contained herein are
based on data believed to be correct. However, no guarantee or warranty of
any kind expressed or implied is made with respect to the information
contained herein.
AES makes no warranty expressed or implied regarding the accuracy of this
data or the results obtained from the use thereof. AES assumes no
responsibilities for injury from the use of this product.
P.O. Box 1007, Katy, Texas 77492 Office: (281) 728-7280 Fax: (281) 391-5655
www.advancedepoxysystems.com
|