Wednesday, October 29, 2008
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: TITE SEAL PVC SOLVENT CEMENT
MSDS No.: T6008
I. Basic Information:
Manufacturer: RADIATOR SPECIALTY COMPANY Contact: Robert Geer
Address: 600 RADIATOR ROAD Information Telephone Number: 704-684--181 1
City, ST Zip: INDIAN TRAIL, NC 28079 Emergency Contact: Rocky Mountain Poision Control Center
Country: Emergency Telephone Number: 303-623-5716
Emergency Restrictions:
Product Name: TITE SEAL PVC SOLVENT CEMENT
MSDS No.: T6008
Issue Date: 10/29/2008
Supersedes Date: 07/07/2003
II. Hazards Identification:
EMERGENCY OVERVIEW
Danger: Extremely Flammable. Vapors may cause Flash Fire. Harmful or Fatal if Swallowed. Vapor Harmful. Eye and Skin Irritant. KEEP AWAY
FROM CHILDREN.
OSHA Regulatory Status
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Potential Health Effects
Route(s) of Entry:
Inhalation and Skin Contact
Health Hazards (Acute and Chronic):
Symptoms of respiratory tract irritation and damage to respiratory epitelium were reported in rats exposed to 5000 ppm THF for 90 days.
Elevation of SGPT suggests a disturbance in liver function. The NOEL was reported to be 200 ppm. Affect centeral nervous system, liver and
kidneys. Causes irritation to skin.
Signs and Symptoms:
Eye Contact: overexposure may result in severe eye injury with corneal or conjuctival inflammation on contact with the liquid. Vapors slightly
uncomfortable.
Skin Absorption: Prolonged or widespread exposure may result in the absorption of harmful amounts of material.
Inhalation: Severe overexposure may result in nausea, dizziness, headache. Can cause drowsiness, irritation of eyes and nasal passages.
Ingestion: Moderately toxic. May cuase nausea, vomiting, diarrhea. May cause mental sluggishness.
Medical Conditions Generally Aggravated by Exposure:
Individuals with pre-existing dieases of the eyes, skin, or respiratory system may have increased susceptibility to the toxicity of excessive
exposures.
Other Health Warnings:
N/D
Potential Environmental Effects
Not Available
III. Composition/Information on Ingredients:
Chemical Name CAS No. % Range Trade Secret
Cyclohexanone 108-94-1 5.0 - 15.0
Furan, tetrahydro- 109-99-9 15.0 - 40.0
Methyl ethyl ketone 78-93-3 30.0 - 60.0
Polyvinyl Chloride Resin Proprietary N/A
IV. First Aid Measures:
Emergency and First Aid Procedures:
Wednesday, October 29, 2008
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: TITE SEAL PVC SOLVENT CEMENT
MSDS No.: T6008
Eye Contact: Flush eyes with clean water for 15 minutes while lifting eyelids and get prompt medical attention.
Skin Contact: Wash with soap and water thoroughly. If adverse effects persist, get prompt medical attention. Launder contaminated clothing
before reuse.
Inhalation: Remove to fresh air. If breathing becomes difficult get prompt medical attention.
Ingestion: DO NOT INDUCE VOMITING! Call Poison Control Center, physician, or hospital emergency room immediately.
Note to Physicians:
N/D
V. Fire Fighting Measures:
Suitable Extinguishing Media:
Water Fog, Foam, Carbon Dioxide, Dry Chemical
Unsuitable Extinguishing Media:
Do not use forced water stream as this could cause the fire to spread. Use shield to protect from rupturing and venting containers.
Products of Combustion:
Carbon monoxide, carbon dioxide, hydrogen chloride and smoke
Protection of Firefighters:
Wear self-contained positive pressure breathing apparatus and protective clothes.
VI. Accidental Release Measures:
Personal Precautions:
Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed.
Environmental Precautions:
Prevent run-off to sewers, streams, or other bodies of water. If run-off occurs, notify proper authorities as required that a spill has occurred. Run off
to sewer may create fire or explosion hazard.
Methods for Containment:
Dike or contain spill and absorb with inert materials (sand, sawdust, absorbent sweeping compounds, rags, etc).
Methods for Cleanup:
Using a non-metalic scoop, place contaminated material into an approved chemical waste container. Where possible, vacuum spilled liquid using
an explosion proof vacuum to recover material.
Other Information:
Eliminate all ignition sources. Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed.
If run-off occurs, notify proper authorities as required that a spill has occured.
VII. Handling and Storage:
Handling Precautions:
Store in the shade between 40癋 - 110癋. Keep away from heat, sparks, open flame and other sources of ignition. Avoid prolonged breathing of
vapor. Use with adequate ventilation. Avoil contact with eyes, skin, and clothing. Train employees on all special handling procedures before they
work with this product.
Storage Precautions:
Follow all precautionary information given on container label, product bulletins and our solvent cementing literature. All handling equipment should
be electrically grounded.
VIII. Exposure Controls/Personal Protection:
Chemical Name OSHA PEL ACGIH TLV Other Limits
Polyvinyl Chloride Resin N/E N/E Not Available
Furan, tetrahydro- 200 ppm 200 ppm Not Available
Methyl ethyl ketone 200 ppm 200 ppm Not Available
Cyclohexanone 25 ppm 25 ppm Not Available
Wednesday, October 29, 2008
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: TITE SEAL PVC SOLVENT CEMENT
MSDS No.: T6008
Engineering Controls:
See Section above for applicable exposure limits. Maintain adequate ventilation.
Avoid breathing vapors. In restricted areas, use approved chemical filter designed to remove vapor. In confined areas, use approved air line type
respirator or hood. A self-contained breathing apparatus is required for vapor concentrations above TLV limits.
Personal Protective Equipment:
For prolonged exposure wear protective safety glasses, PVA coated gloves, and apron. A source of running water should be available to flush or
wash the eyes and skin in case of contact.
IX. Physical and Chemical Properties:
Boiling Point: 151癋 Melting Point: N/A
Boiling Range: Not Available Freezing Point: Not Available
Solubility In Water: Completely soluble in water Evaporation Rate (Butyl Acetate = 1): > 1.0
Flash Point: 6癋 Flash Point Method: TCC
Odor Threshold: Not Available Appearance and Odor: Clear or Gray medium syrupy liquid with
ethereal odor
Vapor Density (AIR = 1): 2.49 Vapor Pressure (mm Hg.): 143
pH Range: Not Available Not Available
Partition Coefficient:
Not Available Auto-Ignition Temp: Not Available
Decomposition Temp:
Lower Explosive Limit: 2.0 Upper Explosive Limit: 11.8
Specific Gravity (H20 = 1): 0.91
Other Information: N/D
X. Stability and Reactivity:
Stability:
Stable
Conditions to Avoid:
See Incompatible materials below.
Incompatible Materials:
Caustics, ammonia, inorganic acids, chlorinated compounds, strong oxidizers and isocyanates.
Hazardous Decomposition Products:
Carbon monoxide, carbon dioxide, hydrogen chloride and smoke
Possibility of Hazardous Reactions:
Will not occur
XI. Toxicological Information:
N/D
XII. Ecological Information:
N/D
XIII. Disposal Considerations:
DISPOSAL: This container may be recycled in a recycling centers when empty. Before offering for recycling, empty the can or bottle by using the
product according to the label. If recycling is not available, wrap the container and discard in the trash. Dispose of unused product in accordance
with all local, state government and federal laws and regulations
Wednesday, October 29, 2008
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: TITE SEAL PVC SOLVENT CEMENT
MSDS No.: T6008
XIV. Transport Information:
Shipping Name: Not Available
DOT Hazard Class: Not Available DOT Subsidiary Hazard Class: Not Available
UN/NA#: Not Available Not Available
Packing Group:
Transportation Information:
Shipping information for containers less than one gallon:
DOT Shipping Name: Consumer Commodity
DOT Hazard Class: ORM-D
The DOT description is provided to assist in the proper shipping classification of this product and may not be suitable for all shipping purposes.
Shipping information for gallon containers and above:
DOT Shipping Name: Adhesive
DOT Hazard Class: 3
Identification Number: UN1133
Packaging Group: II
Label Required: Flammable Liquid
XV. Regulatory Information:
SARA 313 Reportable Chemicals:
Methyl Ethyl Ketone 78-79-3
USA TSCA: All components of this material are listed on the US TSCA Inventory.
State RTK Chemicals:
Methyl Ethyl Ketone 78-79-3
Cyclohexanone 108-94-1
XVI. Other Information:
Liquid Gas Solid
Chemical State: X
Pure Mixture
Chemical Type: 3
X
Hazard Category: 2 1
Acute Chronic Fire
X X X
Pressure Reactive
X
Additional Manufacturer Warnings:
Do not used in confined area without proper ventilation. Contact lenses 2
may cause further damage in case of splash into eye. KEEP AWAY FROM
3
CHILDREN AND ANIMALS!
0
N/E: Not Established
N/D: Not Determined H
N/A: Not Applicable
N/AV: Not Available
Additional Product Information:
While Radiator Specialty Company believes this data is accurate as of the revision date, we make no warranty with respect to the
data and we expressly disclaim all liability for reliance thereon. The data is offered solely for information, investigation, and
verification. Various government agencies may have specific regulations regarding the transportation, handling, storage, use, or
disposal of this product which may not be covered by this MSDS. The user is responsible for full compliance.
|