Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 1 of 1
Revised: 24 May 2007 MSDS No: 20
CLASSIFIED AS HAZARDOUS ACCORDING TO NOHSC CRITERIA
1. Identification of the substance/preparation and company
Product:
Sikadur 32 Part A
Recommended use:
Two component epoxy resin based bonding agent.
Manufacturer/supplier information:
Manufacturer/supplier: Sika Australia Pty Ltd
Street/postbox: 55 Elizabeth Street
Town/city and Post Code: WETHERILL PARK NSW 2164
Country: AUSTRALIA
Phone: (02) 9725 1145
Fax: (02) 9725 3330
General information Operations Manager
Emergency information phone: 1800 033 111
2. Composition/information on ingredients
Chemical characterization:
Filled and modified epoxy resin
Hazardous ingredients:
Ingredient CAS No Concentration
Bisphenol A diglycidyl ether 25068-38-6 >60%
Aliphatic glycidyl ether 68609-97-2 1-10%
Solvent naptha 64742-94-5 1-10%
3. Hazard identification
Hazard Category:
Xi Irritant
Risk Phrase(s):
R36/38: Irritating to eyes and skin.
R43: May cause sensitisation by skin contact.
Safety Phrase(s):
S24 Avoid contact with skin.
S36/37/39: Wear suitable protective clothing, gloves and eye/face protection.
4. First-aid measures
Inhalation:
Remove victim from exposure - avoid becoming a casualty. Remove contaminated clothing and loosen
remaining clothing. Allow patient to assume most comfortable position and keep warm. Keep at rest
until fully recovered. Seek medical advice if effects persist.
Skin contact:
If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water.
If swelling, redness, blistering or irritation occurs seek medical assistance.
Eye contact:
If in eyes, hold eyelids apart and flush the eyes continuously with running water. Continue flushing
until advised to stop by the Poisons Information Centre or a Doctor; or for at least 15 minutes and
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 2 of 1
Revised: 24 May 2007 MSDS No: 20
transport to Doctor or Hospital.
Ingestion:
If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New
Zealand 0800 764 766). Rinse mouth with water. If swallowed, do NOT induce vomiting. Give a glass
of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting occurs give
further water. Seek medical advice.
Notes to physician:
Treat symptomatically. Effects may be delayed.
5. Fire-fighting measures
Specific hazards:
Combustion will produce smoke,carbon dioxide and carbon monoxide.
Special protective precautions and equipment:
On burning may emit toxic fumes. Fire fighters to wear self-contained breathing apparatus and suitable
protective clothing if risk of exposure to vapour or products of combustion.
Suitable extinguishing media:
If material is involved in a fire use foam, dry agent (carbon dioxide, dry chemical powder).
6. Accidental release measures
Small Spills:
Wear protective equipment to prevent skin and eye contamination. Avoid inhalation of vapours. Wipe
up with absorbent (clean rag or paper towels). Collect and seal in properly labelled containers or
drums for disposal.
Large spills:
Slippery when spilt. Avoid accidents, clean up immediately. Wear protective equipment to prevent
skin and eye contamination and the inhalation of vapours. Work up wind or increase ventilation.
Contain - prevent run off into drains and waterways. Use absorbent (soil, sand or other inert material).
Collect and seal in properly labelled containers or drums for disposal. If contamination of sewers or
waterways has occurred advise local emergency services.
7. Handling and storage
Handling:
Avoid skin and eye contact. Use in well ventilated areas.
Storage:
Store in a cool, dry, well-ventilated place and out of direct sunlight. Storage temperature should be
between 5 and 25 0C. Keep containers closed when not in use - check regularly for leaks.
8. Exposure controls/personal protection
National occupational exposure limits:
No value assigned for this specific material by the NOHSC Australia.
However for:
TWA STEL CARCINOGEN NOTICES
ppm mg/m3 ppm mg/m3 CATEGORY
Epichlorhydrin 2 7.6 - - - Sk
As published by the NOHSC Australia.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 3 of 2
Revised: 24 May 2007 MSDS No: 20
Biological Limit Values:
As per the "National Model Regulations for the Control of Workplace Hazardous Substances [NOHSC:
1005 (1994)]" the ingredients in this material do not have a Biological Limit Allocated.
Engineering measures:
Ensure ventilation is adequate to maintain air concentrations below Exposure Standards. Natural
ventilation should be adequate under normal use conditions.
Personal protection equipment:
OVERALLS, SAFETY SHOES, CHEMICAL GOGGLES, GLOVES.
Wear overalls, chemical goggles and impervious gloves. Due to variations in glove construction and
local conditions, the user should make an assessment of the appropriate gloves to use. Wash hands
before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective
equipment before storing or re-using. If risk of inhalation of exists, wear organic vapour/particulate
respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716.
9. Physical and chemical properties
Appearance:
Physical state: Paste
Colour: Grey
Odour: Characteristic
Data relevant to safety:
Solubility: Insoluble in water.
Specific Gravity (20 癈): 1.4
Relative Vapour Density (air=1): <7
Vapour Pressure (20 癈): N Av
Flash Point (癈): 112
Flammability Limits (%): N Av
Autoignition Temperature (癈): 500
(Typical values only - consult specification sheet)
N Av = Not available
10. Stability and reactivity
Chemical stability:
This material is thermally stable when stored and used as directed.
Conditions to avoid:
Elevated temperatures and sources of ignition.
Incompatible Materials:
No information available.
Hazardous decomposition products:
Oxides of carbon and nitrogen, smoke and other toxic fumes.
Hazardous reactions:
No information available.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 4 of 3
Revised: 24 May 2007 MSDS No: 20
11. Toxicological information
No adverse health effects expected if the product is handled in accordance with this Safety Data Sheet and
the product label. Symptoms or effects that may arise if the product is mishandled and overexposure occurs
are:
Acute Effects:
Inhalation: Material may be irritant to mucous membranes and respiratory tract.
Skin contact: Contact with skin will result in irritation. A skin sensitiser. Repeated or prolonged skin
contact may lead to allergic contact dermatitis.
Eye contact: An eye irritant.
Ingestion:
Swallowing can result in nausea, vomiting and irritation of the gastrointestinal tract.
Long Term Effects:
No information available for product.
Acute toxicity / Chronic toxicity:
No LD50 data available for the product.
12. Ecological information
Avoid contaminating waterways.
Ecotoxicity:
Harmful to aquatic organisms.
Persistence and degradability:
Not readily biodegradable.
Mobility:
Product is insoluble .in water.
13. Disposal considerations
Refer to State/Territory Land Waste Management Authority.
14. Transport information
ADG/ADR/RID
Not classified as Dangerous Goods by the criteria of the ADG Code.
IMDG
Not classified as Dangerous Goods by the criteria of the IMDG Code for transport by sea.
IATA
Not classified as Dangerous Goods by the criteria of the IATA Dangerous Goods Regulations for
transport by air.
15. Regulatory information
Poisons Schedule (Aust):
This material is a Scheduled Poison S5 and must be stored, maintained and used in accordance with
the relevant regulations.
All the constituents of this material are listed on the Australian Inventory of Chemical Substances (AICS).
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 5 of 4
Revised: 24 May 2007 MSDS No: 20
16. Other information
Reason(s) For Issue: Revised
Material Safety Data Sheets are updated frequently. Please ensure that you have a current copy. MSDS
may be obtained from the following website: www.sika.com.au
The information contained in this Safety Date Sheet corresponds to our level of knowledge at the time of
publication. All warranties are excluded. Our most current General Sales Conditions shall apply. Please
consult the Technical Data Sheet prior to any use and processing.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 1 of 5
Revised: 24 May 2007 MSDS No: 21
CLASSIFIED AS HAZARDOUS ACCORDING TO NOHSC CRITERIA
1. Identification of the substance/preparation and company
Product:
Sikadur 32 Part B Normal
Recommended use:
Two Component Solvent Free High Build Epoxy based Protective Coating
Manufacturer/supplier information:
Manufacturer/supplier: Sika Australia Pty Ltd
Street/postbox: 55 Elizabeth Street
Town/city and Post Code: WETHERILL PARK NSW 2164
Country: AUSTRALIA
Phone: (02) 9725 1145
Fax: (02) 9725 3330
General information Operations Manager
Emergency information phone: 1800 033 111
2. Composition/information on ingredients
Chemical characterization:
Modified polyamines
Hazardous ingredients:
Ingredient CAS No Concentration
Benzyl alcohol 100-51-6 10-30%
Trietylenetetramine 112-24-3 1- 10%
Isophoronediamine 2855-13-2 10-30%
2,4,6 璗ri(dimethylaminomethyl)phenol 90-72-2 1 -10%
Solvent naptha 64742-94-5 1 -10%
3. Hazard identification
Hazard Category:
Xi Irritant
C Corrosive
Risk Phrase(s):
R20/22: Harmful by inhalation and if swallowed.
R34: Causes burns.
R43: May cause sensitisation by skin contact.
Safety Phrase(s)
S24/ Avoid contact with skin.
S36/37/39: Wear suitable protective clothing, gloves and eye/face protection.
S45 In case of accident or if you feel unwell seek medical advice immediately.
4. First-aid measures
Inhalation:
Remove victim from exposure - avoid becoming a casualty. In case of possible respiratory irritation or if
feeling unwell in case of prolonged exposure, obtain medical attention.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 2 of 5
Revised: 24 May 2007 MSDS No: 21
Skin contact:
For gross contamination, immediately drench with water and remove clothing. Continue to flush skin
and hair with plenty of water (and soap if material is insoluble). For skin burns, cover with a clean, dry
dressing until medical help is available. If blistering occurs, do NOT break blisters. If swelling,
redness, blistering, or irritation occurs seek medical assistance.
Eye contact:
Immediately irrigate with copious quantities of water for 15 minutes. Eyelids to be held open. Remove
clothing if contaminated and wash skin. Urgently seek medical assistance. Transport to hospital or
medical centre.
Ingestion:
If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New
Zealand 0800 764 766). Immediately rinse mouth with water. If swallowed, do NOT induce vomiting.
Give a glass of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting
occurs give further water. Get to a doctor or hospital quickly.
Notes to physician:
Treat symptomatically.
5. Fire-fighting measures
Specific hazards:
Thermal decomposition or burning may release oxides of carbon, nitrogen, and other toxic gases.
Special protective precautions and equipment:
On burning may emit toxic fumes. Fire fighters to wear self-contained breathing apparatus and suitable
protective clothing if risk of exposure to vapour or products of combustion.
Suitable extinguishing media:
If material is involved in a fire use foam, dry chemical and carbon dioxide.
6. Accidental release measures
Small Spills:
Wear protective equipment to prevent skin and eye contamination. Avoid inhalation of vapours. Wipe
up with absorbent (clean rag or paper towels). Collect and seal in properly labelled containers or
drums for disposal.
Large spills:
Slippery when spilt. Avoid accidents, clean up immediately. Wear protective equipment to prevent
skin and eye contamination and the inhalation of vapours. Work up wind or increase ventilation.
Contain - prevent run off into drains and waterways. Use absorbent (soil, sand or other inert material).
Collect and seal in properly labelled containers or drums for disposal. If contamination of sewers or
waterways has occurred advise local emergency services.
7. Handling and storage
Handling:
Mix in a well ventilated area.
Avoid skin and eye contact and inhalation of vapour.
Storage:
Store in a cool, dry, well-ventilated place and out of direct sunlight.
Keep containers closed when not in use - check regularly for leaks.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 3 of 5
Revised: 24 May 2007 MSDS No: 21
8. Exposure controls/personal protection
National occupational exposure limits:
No value assigned for this specific material by the NOHSC Australia.
Biological Limit Values:
As per the "National Model Regulations for the Control of Workplace Hazardous Substances [NOHSC:
1005 (1994)]" the ingredients in this material do not have a Biological Limit Allocated.
Engineering measures:
Ensure ventilation is adequate to maintain air concentrations below Exposure Standards. Use with
local exhaust ventilation or while wearing appropriate respirator. Keep containers closed when not in
use.
Personal protection equipment:
OVERALLS, SAFETY SHOES, CHEMICAL GOGGLES, GLOVES.
Wear overalls, chemical goggles and impervious gloves. Due to variations in glove construction and
local conditions, the user should make an assessment of the appropriate gloves to use. Wash hands
before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective
equipment before storing or re-using. If risk of inhalation of exists, wear organic vapour/particulate
respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716.
9. Physical and chemical propertiesAppe
Appearance:
Physical state: Paste
Colour: Grey
Odour: Amine odour
Data relevant to safety:
Solubility: Partly soluble in water.
Density (20 癈): 1.4 g/cm3
Flash Point (癈): 94
Auto Ignition (癈): > 350
PH (20 癈): 11
(Typical values only - consult specification sheet)
10. Stability and reactivity
Chemical stability:
This material is thermally stable when stored and used as directed.
Conditions to avoid:
Elevated temperatures and sources of ignition.
Incompatible Materials:
No information available.
Hazardous decomposition products:
Oxides of carbon and nitrogen, smoke and other toxic fumes.
Hazardous reactions:
No information available.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 4 of 5
Revised: 24 May 2007 MSDS No: 21
11. Toxicological information
No adverse health effects expected if the product is handled in accordance with this Safety Data Sheet and
the product label. Symptoms or effects that may arise if the product is mishandled and overexposure occurs
are:
Acute Effects:
Inhalation: Harmful by inhalation. Material may be irritant to mucous membranes and respiratory tract.
Skin contact: The material is corrosive to skin. The possibility of allergic sensitisation should be
considered.
Eye contact: The material is corrosive to eyes.
Ingestion: Swallowing can result in nausea, vomiting, diarrhoea, abdominal pain and chemical burns to
the gastrointestinal tract.
Long Term Effects:
No information available for product.
Acute toxicity / Chronic toxicity:
No LD50 data available for the product.
12. Ecological information
Avoid contaminating waterways.
Ecotoxicity:
The material is harmful to aquatic organisms.
Persistence and degradability:
The product is expected to be partially or slowly biodegradable..
Mobility:
The product is sparingly soluble in water.
13. Disposal considerations
Refer to State/Territory Land Waste Management Authority.
14. Transport information
ADG/ADR/RID
UN No: 1759
Dangerous Goods Class: 8
Packing Group: III
Hazchem Code: 2R
Emergency Response Guide No: 37
Proper Shipping Name: CORROSIVE LIQUID, N.O.S. (contains Triethylenetetramine)
Segregation Dangerous Goods: Not to be loaded with explosives (Class 1), dangerous when wet
substances (Class 4.3), oxidising agents (Class 5.1), organic peroxides (Class 5.2), cyanides of Class
6, radioactive substances (Class 7) or food and food packaging in any quantity, however exemptions
may apply. Note that material is incompatible with acids and alkalis.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 5 of 4
Revised: 24 May 2007 MSDS No: 21
IMDG
UN No: 1759
Dangerous Goods Class: 8
Packing Group: III
Proper Shipping Name: CORROSIVE LIQUID, N.O.S. (contains Triethylenetetramine)
IATA
UN No: 1760
Dangerous Goods Class: 8
Packing Group: III
Proper Shipping Name: CORROSIVE LIQUID, N.O.S. (contains Triethylenetetramine)
15. Regulatory information
Poisons Schedule (Aust):
This material is a Scheduled Poison S5 and must be stored, maintained and used in accordance with
the relevant regulations.
All the constituents of this material are listed on the Australian Inventory of Chemical Substances (AICS).
16. Other information
Reason(s) For Issue: Revised
Material Safety Data Sheets are updated frequently. Please ensure that you have a current copy. MSDS
may be obtained from the following website: www.sika.com.au
The information contained in this Safety Date Sheet corresponds to our level of knowledge at the time of
publication. All warranties are excluded. Our most current General Sales Conditions shall apply. Please
consult the Technical Data Sheet prior to any use and processing.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 1 of 1
Revised: 31-Oct-2007 MSDS No: 103
CLASSIFIED AS HAZARDOUS ACCORDING TO NOHSC CRITERIA
1. Identification of the substance/preparation and company
Product:
Sikadur 32 Part B Long Pot Life
Recommended use:
Two Component Epoxy Resin Based Bonding Agent.
Manufacturer/supplier information:
Manufacturer/supplier: Sika Australia Pty Ltd
Street/postbox: 55 Elizabeth Street
Town/city and Post Code: WETHERILL PARK NSW 2164
Country: AUSTRALIA
Phone: (02) 9725 1145
Fax: (02) 9725 3330
General information Operations Manager
Emergency information phone: 1800 033 111
2. Composition/information on ingredients
Chemical characterization:
Modified polyamines
Hazardous ingredients:
Ingredient CAS No Concentration
Benzyl alcohol 100-51-6 10-30%
Trietylenetetramine 112-24-3 1- 10%
Isophoronediamine 2855-13-2 1 -10%
Aliphatic polyamine adduct 1 ?10%
Solvent naphtha 64742-94-5 1 -10%
3. Hazard identification
Hazard Category:
Xi Irritant
C Corrosive
Risk Phrase(s):
R20/22: Harmful by inhalation and if swallowed.
R34: Causes burns.
R43: May cause sensitisation by skin contact.
Safety Phrase(s)
S24/ Avoid contact with skin.
S36/37/39: Wear suitable protective clothing, gloves and eye/face protection.
S45 In case of accident or if you feel unwell seek medical advice immediately.
4. First-aid measures
Inhalation:
Remove victim from exposure - avoid becoming a casualty. In case of possible respiratory irritation or if
feeling unwell in case of prolonged exposure, obtain medical attention.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 2 of 1
Revised: 31-Oct-2007 MSDS No: 103
Skin contact:
For gross contamination, immediately drench with water and remove clothing. Continue to flush skin
and hair with plenty of water (and soap if material is insoluble). For skin burns, cover with a clean, dry
dressing until medical help is available. If blistering occurs, do NOT break blisters. If swelling,
redness, blistering, or irritation occurs seek medical assistance.
Eye contact:
Immediately irrigate with copious quantities of water for 15 minutes. Eyelids to be held open. Remove
clothing if contaminated and wash skin. Urgently seek medical assistance. Transport to hospital or
medical centre.
Ingestion:
If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New
Zealand 0800 764 766). Immediately rinse mouth with water. If swallowed, do NOT induce vomiting.
Give a glass of water to drink. Never give anything by the mouth to an unconscious patient. If vomiting
occurs give further water. Get to a doctor or hospital quickly.
Notes to physician:
Treat symptomatically.
5. Fire-fighting measures
Specific hazards:
Thermal decomposition or burning may release oxides of carbon, nitrogen, and other toxic gases.
Special protective precautions and equipment:
On burning may emit toxic fumes. Fire fighters to wear self-contained breathing apparatus and suitable
protective clothing if risk of exposure to vapour or products of combustion.
Suitable extinguishing media:
If material is involved in a fire use foam, dry chemical and carbon dioxide.
6. Accidental release measures
Small Spills:
Wear protective equipment to prevent skin and eye contamination. Avoid inhalation of vapours. Wipe
up with absorbent (clean rag or paper towels). Collect and seal in properly labelled containers or
drums for disposal.
Large spills:
Slippery when spilt. Avoid accidents, clean up immediately. Wear protective equipment to prevent
skin and eye contamination and the inhalation of vapours. Work up wind or increase ventilation.
Contain - prevent run off into drains and waterways. Use absorbent (soil, sand or other inert material).
Collect and seal in properly labelled containers or drums for disposal. If contamination of sewers or
waterways has occurred advise local emergency services.
7. Handling and storage
Handling:
Mix in a well ventilated area.
Avoid skin and eye contact and inhalation of vapour.
Storage:
Store in a cool, dry, well-ventilated place and out of direct sunlight.
Keep containers closed when not in use - check regularly for leaks.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 3 of 2
Revised: 31-Oct-2007 MSDS No: 103
8. Exposure controls/personal protection
National occupational exposure limits:
No value assigned for this specific material by the NOHSC Australia.
Biological Limit Values:
As per the "National Model Regulations for the Control of Workplace Hazardous Substances [NOHSC:
1005 (1994)]" the ingredients in this material do not have a Biological Limit Allocated.
Engineering measures:
Ensure ventilation is adequate to maintain air concentrations below Exposure Standards. Use with
local exhaust ventilation or while wearing appropriate respirator. Keep containers closed when not in
use.
Personal protection equipment:
OVERALLS, SAFETY SHOES, CHEMICAL GOGGLES, GLOVES.
Wear overalls, chemical goggles and impervious gloves. Due to variations in glove construction and
local conditions, the user should make an assessment of the appropriate gloves to use. Wash hands
before smoking, eating, drinking or using the toilet. Wash contaminated clothing and other protective
equipment before storing or re-using. If risk of inhalation of exists, wear organic vapour/particulate
respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716.
9. Physical and chemical properties
Appearance:
Physical state: Paste
Colour: Grey
Odour: Amine odour
Data relevant to safety:
Solubility: Partly soluble in water.
Density (20 癈): 1.4 g/cm3
Flash Point (癈): 94
Auto Ignition (癈): > 350
(Typical values only - consult specification sheet)
10. Stability and reactivity
Chemical stability:
This material is thermally stable when stored and used as directed.
Conditions to avoid:
Elevated temperatures.
Incompatible Materials:
Strong acids and oxidizing agents.
Hazardous decomposition products:
Oxides of carbon and nitrogen, smoke and other toxic fumes.
Hazardous reactions:
No information available.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 4 of 3
Revised: 31-Oct-2007 MSDS No: 103
11. Toxicological information
No adverse health effects expected if the product is handled in accordance with this Safety Data Sheet and
the product label. Symptoms or effects that may arise if the product is mishandled and overexposure occurs
are:
Acute Effects:
Inhalation: Harmful by inhalation. Material may be irritant to mucous membranes and respiratory tract.
Skin contact: The material is corrosive to skin. The possibility of allergic sensitisation should be
considered.
Eye contact: The material is corrosive to eyes.
Ingestion: Swallowing can result in nausea, vomiting, diarrhoea, abdominal pain and chemical burns to
the gastrointestinal tract.
Long Term Effects:
No information available for product.
Acute toxicity / Chronic toxicity:
No LD50 data available for the product.
12. Ecological information
Avoid contaminating waterways.
Ecotoxicity:
The material is harmful to aquatic organisms.
Persistence and degradability:
The product is expected to be partially or slowly biodegradable..
Mobility:
The product is sparingly soluble in water.
13. Disposal considerations
Refer to State/Territory Land Waste Management Authority.
14. Transport information
ADG/ADR/RID
UN No: 1760
Dangerous Goods Class: 8
Packing Group: III
Hazchem Code: 2R
Emergency Response Guide No: 37
Proper Shipping Name: CORROSIVE LIQUID, N.O.S. (contains Triethylenetetramine)
Segregation Dangerous Goods: Not to be loaded with explosives (Class 1), dangerous when wet
substances (Class 4.3), oxidising agents (Class 5.1), organic peroxides (Class 5.2), cyanides of Class
6, radioactive substances (Class 7) or food and food packaging in any quantity, however exemptions
may apply. Note that material is incompatible with acids.
Safety Data Sheet
According to NOHSC:2011(2003)
Version: 1.0 Page: 5 of 4
Revised: 31-Oct-2007 MSDS No: 103
IMDG
UN No: 1760
Dangerous Goods Class: 8
Packing Group: III
Proper Shipping Name: CORROSIVE LIQUID, N.O.S. (contains Triethylenetetramine)
IATA
UN No: 1760
Dangerous Goods Class: 8
Packing Group: III
Proper Shipping Name: CORROSIVE LIQUID, N.O.S. (contains Triethylenetetramine)
15. Regulatory information
Poisons Schedule (Aust):
This material is a Scheduled Poison S5 and must be stored, maintained and used in accordance with
the relevant regulations.
All the constituents of this material are listed on the Australian Inventory of Chemical Substances (AICS).
16. Other information
Reason(s) For Issue: Revised
Material Safety Data Sheets are updated frequently. Please ensure that you have a current copy. MSDS
may be obtained from the following website: www.sika.com.au
The information contained in this Safety Date Sheet corresponds to our level of knowledge at the time of
publication. All warranties are excluded. Our most current General Sales Conditions shall apply. Please
consult the Technical Data Sheet prior to any use and processing.
|