MATERIAL SAFETY DATA SHEET
Page: 1
310410.00
1/8/2008
PRODUCT NAME: SATIN SEALER HMIS CODES: H F R P
PRODUCT CODE: C11204, C11201, 11205 2*3 0 X
DOT CLASS: PAINT,3,UN1263,PGII
================== SECTION I - MANUFACTURER IDENTIFICATION =================
MANUFACTURER'S NAME: Glitsa American
ADDRESS: 327 S Kenyon, Seattle WA 98108
EMERGENCY PHONE: Call Chemtrec 1-800-424-9300 (spill, leak, fire, accident)
INFORMATION PHONE: 206-763-2855
NAME OF PREPARER: Rudd Company, Inc.
========== SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION =========
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT
------------------------------------------------------------------------------------------------------------------------------------
ETHYL ALCOHOL 64-17-5 40 68 18
ACGIH TLV: 1000 ppm OSHA PEL: 1000 ppm Other: 1880 mg/m3
ISOBUTYL ALCOHOL 78-83-1 9 68 9
ACGIH TLV: 50 ppm OSHA PEL: 100 ppm Other: 152 mg/m3
N-BUTYL ACETATE 123-86-4 10 68 7
ACGIH TLV: 150 ppm OSHA PEL: 150 ppm Other: 200 ppm ACGIH STEL
C8+ AROMATICS 64742-95-6 8 77 4
ACGIH TLV: 80 ppm OSHA PEL: 500 ppm.
STODDARD SOLVENT, MINERAL SPIRITS 8052-41-3 2 68 3
ACGIH TLV: 100 ppm OSHA PEL: 500 ppm Other: 525 mg/m3
* XYLENE 1330-20-7 25 77 3
ACGIH TLV: 100 ppm OSHA PEL: 100 ppm Other: 150 ppm STEL
METHYL PROPYL KETONE 107-87-9 28 68 2
ACGIH TLV: 200 ppm OSHA PEL: 200 ppm Other: 150 ppm (STEL)
* 1,2,4-TRIMETHYLBENZENE 95-63-6 1
ACGIH TLV: 25 ppm OSHA PEL: Not Est Other: 123 mg/m3
ETHYL BENZENE 100-41-4 10 77 .74
ACGIH TLV: 100 ppm OSHA PEL: 100 ppm Other: 434 mg/m3
* FORMALDEHYDE** 50-00-0 <0.1**
ACGIH TLV: 0.30 ppm (C) OSHA PEL: 0.75 ppm Other: 0.37mg/m3 (C)
* Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372.
**SEE SECTION VIII FOR POTENTIAL TO EMIT ADDITIONAL FORMALDEHYDE.
=============== SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ============
BOILING RANGE: 168 - 309
DENSITY: 8.11 lb/gl
V.O.C.: 4.13 lb/gl 495 g/l (less water and exempt solvents)
4.13 lb/gl 495 g/l (Emitted VOC)
SOLIDS % BY WEIGHT: 49.0
VAPOR DENSITY: Heavier than air.
EVAPORATION RATE: Moderate (compared to n-butyl acetate)
SOLUBILITY IN WATER: Moderate
APPEARANCE AND ODOR: Translucent yellow liquid, solvent odor.
================= SECTION IV - FIRE AND EXPLOSION HAZARD DATA ==============
FLASH POINT: 56 Deg. F METHOD USED: P-Marten
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: 1 UPPER: 19
MATERIAL SAFETY DATA SHEET
Page: 2
310410.00
1/8/2008
EXTINGUISHING MEDIA: FOAM, CO2, DRY CHEMICAL, WATER FOG
SPECIAL FIREFIGHTING PROCEDURES:
Evacuate all unnecessary personnel. Use full protective equipment, including self-contained breathing apparatus. Use
water spray, preferably fog, to cool closed containers to prevent pressure build-up and possible explosion. Direct water
stream is not recommended for oil base fires. Product may float and reignite on surface of water. Do not allow product
or runoff from fire control to enter storm or sanitary sewers, lakes, rivers, streams or waterways.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Explosive air-vapor mixtures may form which are dangerous when exposed to heat or flame. Vapors are heavier than air and
may travel along the ground, or be moved by ventilation, and ignited by pilot lights, stoves, heaters, electric motors,
sparks, flame, smoking, static discharge or other ignition sources even at locations distant from material handling site
if inadequately ventilated. Free falling streams of liquid may cause static electricity build-up and create fire
hazard.
======================== SECTION V - REACTIVITY DATA =======================
STABILITY:
Stable
CONDITIONS TO AVOID:
High temperature and humidity, ignition sources and vapor build-up.
INCOMPATIBILITY (MATERIALS TO AVOID):
Strong Oxidizing agents Acids Alkalis Bases Nitric Acid Alkali Metals
HAZARDOUS DECOMPOSITION OR BYPRODUCTS:
Carbon Monoxide Carbon Dioxide Hydrocarbons Methanol Formaldehyde Other Organic Compounds
HAZARDOUS POLYMERIZATION:
Will not occur.
=== SECTION VI - HEALTH HAZARD DATA AND SYMPTOMS OF UNPROTECTED EXPOSURE ===
PRIMARY ROUTE(S) OF EXPOSURE: Inhalation, skin contact, ingestion.
INHALATION:
Vapors and mists may irritate nose, throat and lungs (burning, stinging, coughing). May cause headache, dizziness,
nausea, weakness, shortness of breath and loss of coordination. Intentional misuse by deliberately concentrating and
inhaling the contents may be harmful or fatal. Exposure to extremely high vapor concentrations may cause
unconsciousness and asphyxiation. Always wear a NIOSH approved respitator with functioning organic vapor cartridges and
provide adequate ventilation at the jobsite during and after application. If formaldehyde concentrations are unknown,
use formaldehyde specific cartridges.
EYE CONTACT:
Contact with liquid or vapors causes severe irritation (redness, watering, itching, stinging, blurred vision).
SKIN CONTACT:
Contact may cause severe irritation (dryness, itching, cracking, rash and swelling) and possible burns.
SKIN ABSORPTION:
May be absorbed through the skin in harmful amounts. Repeated and prolonged contact may have a cumulative effect.
Symptoms may include headache, dizziness, nausea, weakness, loss of coordination.
SWALLOWING:
May be harmful or fatal. Causes nausea, vomiting, diarrhea and severe central nervous system depression (headache,
dizziness, nausea, loss of coordination).
Aspiration into the lungs may occur during ingestion or vomiting, resulting in lung injury.
CHRONIC EFFECTS FROM LONG TERM UNPROTECTED EXPOSURE:
Contains ingredients suspected of causing or known to cause damage to:kidneys, liver, lungs,
eyes, heart, brain and nervous system, dermatitis or other skin disorders, Always wear appropriate
respiratory, eye and skin protection during use. Ventilate well during and after application.
Exposure to formaldehyde may cause sensitization and allergic skin reaction resulting in contact dermatitis. Some
reports also suggest sensitization and allergic respiratory reaction resulting in asthma-like symptoms. Always wear
appropriate respiratory and skin protection during use. Ventilate well during and after application.
The following statement is required by California Proposition 65 (Safe Drinking Water and Toxic Reform Act of 1986).
MATERIAL SAFETY DATA SHEET
Page: 3
310410.00
1/8/2008
Warning! This product contains a chemical known to the state of California to cause cancer.
CARCINOGEN:
Formaldehyde is classified as a known human carcinogen by the International Agency of Research on Cancer (IARC). In
chronic inhalation studies, exposure to high concentrations caused nasal cancer in laboratory rats. Risk of cancer
depends on level and duration of unprotected exposure. Always wear a NIOSH approved respitator with functioning organic
vapor cartridges and provide adequate ventilation at the jobsite during and after application. If formaldehyde
concentrations are unknown, use formaldehyde specific cartridges. Before initial use, consult OSHA's formaldehyde
standard (29 CFR 1910.1048). Also consult section VIII of this MSDS. Ethylbenzene is classified as a potential human
carcinogen based on laboratory animal studies. Risk of cancer depends on level and duration of exposure.
NTP CARCINOGEN: Yes IARC MONOGRAPHS: Yes OSHA REGULATED: Yes
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY UNPROTECTED EXPOSURE:
Respiratory tract irritation, nausea, eye disorders, skin disorders, sensitization to chemical substances.
============= SECTION VII - EMERGENCY AND FIRST AID PROCEDURES ============
INHALATION:
Remove from exposure to fresh air. If breathing is difficult, give oxygen. If breathing has stopped, give artificial
respiration. Keep person warm and quiet. Get medical attention immediately.
EYE CONTACT:
Immediately flush with plenty of water for 15 minutes, while lifting upper and lower eyelids. Get medical attention.
SKIN CONTACT:
Immediately wash with soap and water. Remove contaminated clothing and shoes. Wash or clean thoroughly before reuse. Get
medical attention if irritation persists.
SWALLOWING:
DO NOT induce vomiting. Call Poison Control Center (1-800-222-1222) or physician immediately. Note: Aspiration of
solvents may result in chemical pneumonia.
OTHER:
Have Material Safety Data Sheet available when calling Poison Control Center (1-800-222-1222) or physician; or when
going to the emergency room.
============ SECTION VIII - SAFE HANDLING AND USE INFORMATION =============
This product contains a resin with the potential to emit additional formaldehyde during use. Exposure levels will vary
with jobsite conditions and controls, including ventilation, temperature and humidity. Before initial use,consult OSHA's
formaldehyde standard (29 CFR 1910.1048).
RESPIRATORY PROTECTION:
Ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air
monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate, properly fitted respirator
(NIOSH approved) during and after application. Follow respirator manufacturer's instructions for use.
VENTILATION:
USE ONLY WITH ADEQUATE VENTILATION. Provide the maximum ventilation jobsite conditions allow (including fans, open
doors, windows or other appropriate means of ventilation), to prevent vapor build-up.
HAND PROTECTION:
Wear impermeable gloves to prevent skin contact. Consult safety equipment supplier for specific recommendations of
construction materials.
EYE PROTECTION:
Wear chemical goggles designed to protect eyes against vapors, liquid splash and mists unless full facepiece respirator
is worn. Note: Contact lenses may contribute to the severity of an eye injury and should not be worn when working with
chemicals.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT:
Wear protective clothing, including headcap, to avoid skin contact with liquid or overspray.
WORK/HYGIENIC PRACTICES:
MATERIAL SAFETY DATA SHEET
Page: 4
310410.00
1/8/2008
Eye washes and safety showers are recommended in the workplace. Wash hands after using and before eating, drinking or
using tobacco products. Thoroughly clean contaminated clothing and shoes before reuse. Periodically monitor exposure
levels to hazardous ingredients listed in section II and review permissible limits.
================ SECTION IX - SPILL AND LEAK PROCEDURES =================
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Eliminate ignition sources and ventilate area. Evacuate all unnecessary personnel. Wear full protective equipment. Dike
drains to prevent entering storm or sanitary sewers, rivers, streams or waterways. Contain spill and cover with inert
absorbent material. Take up using non-sparking tools (aluminum, brass or copper) and place mixture into containers for
disposal. Note: Some spills or releases may require special reporting to local, state or federal agencies.
WASTE DISPOSAL METHOD:
Waste material and empty containers must be disposed of in accordance with all local, state and federal environmental
control regulations. Use only approved waste management facilities.
===================== SECTION X - SPECIAL PRECAUTIONS =====================
KEEP OUT OF REACH OF CHILDREN. FOR INDUSTRIAL USE ONLY!
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
Keep liquid and vapors away from heat, sparks and flame. Turn off or remove all sources of ignition. Use proper methods
of ventilation to prevent vapor build-up. Avoid contact with hot metal surfaces. When pouring large volumes, avoid free
fall of liquids in excess of a few inches to prevent static charge build-up. Avoid breathing vapors and sanding or
grinding dusts. Avoid contact with eyes and skin. Do not take internally. Use adequate methods of ventilation,
respiratory and personal protective equipment. Do not reuse, weld, drill or heat empty containers which may contain
explosive vapors. Follow label warnings until thoroughly cleaned or sent for disposal. Do not remove or deface label.
Do not transfer to unlabeled container.
Consult current OSHA guidelines for specific handling requirements when working with formaldehyde.
OTHER CAUTIONS:
Keep container closed when not in use and during transit. Do not store above 120 deg. F (50 deg. C). Keep in upright
position and protect container from damage. When storing large quantites or when specified by local building or fire
codes, store in buildings or areas designed and protected for storage of products with this flammability rating. Do not
store where contact with incompatible material could occur, even during an accidental spill or release. Before using
two-component coatings, read the MSDS and label of both products. Mixtures will have hazards of both components. To
avoid spontaneous combustion, soak soiled oily rags and waste in water filled metal containers.
========================= SECTION XI - DISCLAIMER ==========================
DISCLAIMER: THE INFORMATION CONTAINED HEREIN HAS BEEN COMPILED FROM SOURCES CONSIDERED TO BE RELIABLE. TO THE BEST OF
OUR KNOWLEDGE AND BELIEF ALL INFORMATION IS ACCURATE AND IS PROVIDED IN GOOD FAITH. HOWEVER, NO GUARANTEE OF ACCURACY IS
MADE OR IMPLIED.
|