MATERIAL SAFETY DATA SHEET
SECTION 1:PRODUCT AND COMPANY IDENTIFICATION
Product Name: UK300-Color-Professional Sizes
Manufacturer: Color Rite Distributing Inc.
1817 E. Ave. Q, Ste. C-24
Palmdale, CA 93550
Information Phone Number: 800-736-7980
Emergency Phone Number:
MSDS Date of Preparation: 01/08/2009
Product Use: Paint for consumer and professional use
SECTION 2: HAZARDS IDENTIFICATION
Viscous liquid with a solvent odor.
EMERGENCY OVERVIEW: WARNING! Flammable liquid and vapor. Keep away from heat, sparks, flames
and other sources of ignition. Do not smoke. Turn off stoves, heaters, electric motors and other sources of ignition
until all vapors/odors are gone. Causes severe eye irritation. May cause skin irritation. Repeated skin exposure may
cause allergic skin reaction. May be harmful if absorbed through the skin. Inhalation of vapors may cause irritation,
headache, dizziness and drowsiness. Harmful or fatal if swallowed. This product contains lead. Overexposure to
lead may cause lead poisoning. Cancer Hazard. Reproductive Hazard. Birth Defects Hazard.
This product is hazardous by definition of Hazard Communication Standard (29 CFR 1910.1200). Category:
Flammable, Irritant, Target Organ Effects, Carcinogen, Sensitizer.
Refer to Section 11 for detailed information on health effects.
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS# %
Ethylbenzene 100-41-4 1-5
1-Methoxy-2-propyl acetate 108-65-6 1-5
Toluene 108-88-3 5-10
n-Butyl Acetate 123-86-4 60-70
Lead Chromate Molybdate Sulfate 12656-85-8 1-5
Antimony Trioxide 1309-64-4 0.1-1
Xylenes 1330-20-7 10-20
Carbon Black 1333-86-5 1-5
Titanium Dioxide 13463-67-7 20-30
Naphtha 64742-89-8 5-10
Aromatic Naphtha 64742-95-6 1-5
n-Butyl Alcohol 71-36-3 10-20
Lead 7439-92-1 10-20
Barium 7440-39-3 1-5
Lead Sulfate 7446-14-2 5-10
Lead Chromate 7758-97-6 10-20
Graphite 7782-42-5 10-20
Isobutyl Alcohol 78-83-1 1-5
Page 1 of 6
MATERIAL SAFETY DATA SHEET
Methyl Ethyl Ketone 78-93-3 5-10
Naphtha 8052-41-3 1-5
1,2,4-Trimethylbenzene 95-63-6 1-5
SECTION 4: FIRST AID MEASURES
Eye: Rinse thoroughly with water for at least 15 minutes, holding the eye lids open to be sure the material is
washed out. Get immediate medical attention.
Skin: Remove contaminated clothing. Flush area with water for 15 minutes then wash exposed area with soap and
water. Get medical attention if irritation or symptoms of exposure develop. Launder clothing before re-use.
Inhalation: Remove victim to fresh air. Give artificial respiration if needed. If breathing is difficult, oxygen
should be administered by qualified personnel. Get immediate medical attention.
Ingestion: If ingestion occurs rinse mouth with a small amount of water. Immediately call local poison control
center or go to an emergency department. Aspiration hazard ?DO NOT Induce Vomiting. Never give anything by
mouth to an unconscious or drowsy person.
Note: If ingestion, any type of overexposure or symptoms of overexposure occur during or following the use of this
product, contact a poison control center, emergency room or physician immediately. Have this MSDS available.
SECTION 5: FIRE-FIGHTING MEASURES
Extinguishing Media: Use foam, carbon dioxide or dry chemical.
Special Fire Fighting Procedures: Wear approved, positive pressure, self-contained breathing apparatus and full
protective clothing. Cool fire exposed containers with water.
Unusual Fire Hazards: Flammable liquid and vapor. Keep this product away from heat, open flames, sparks or other
sources of ignition (i.e. pilot lights, electric motors, static electricity). Invisible vapors can travel along surfaces to a
source of ignition and flash back. Do not smoke while using this product or until all vapors have dissipated. Container
may rupture or explode in the heat of a fire. Do not apply to hot surfaces. Vapors may form explosive mixtures with air
and will collect in low areas.
Hazardous Decomposition Products: Carbon dioxide, carbon monoxide, hydrocarbons, oxides of lead, chromium,
molybdenum and sulfur.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Spill: Evacuate the area. Wear appropriate personal protective equipment. Eliminate all sources of ignition.
Ventilate area. Collect material into a suitable, clean container for disposal. Report spills and releases as required
to appropriate authorities.
SECTION 7: HANDLING AND STORAGE
Handling: Avoid contact with eyes and skin. Avoid breathing vapors and mists. Use only with adequate
ventilation. Wash exposed skin thoroughly with soap and water after use Keep away from heat, sparks, flames and
all other sources of ignition (i.e. pilot lights, electric motors, static electricity). Do not smoke while using this
product or until all vapors have dissipated. Electrically bond and ground containers when pouring. Avoid free fall
of liquid in excess of a few inches. Static electricity can accumulate and cause spark and ignition of solvent vapors.
Do not apply on toys or other children's articles, furniture or interior surfaces of any dwelling or facility. Do not
apply on those exterior surfaces of any dwelling units, such as windowsills, porches, stairs or railings to which
children may commonly be exposed.
Page 2 of 6
MATERIAL SAFETY DATA SHEET
Storage Store in a cool, well ventilated area at temperatures below 120篎 (48.9篊). Do not store in direct sunlight.
Store large quantities in buildings designed and protected for storage of NFPA Class IB flammable liquids.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
Exposure Limits
Chemical Name
Ethylbenzene 100 ppm TWA OSHA PEL
100 ppm TWA, 125 ppm STEL ACGIH TLV
1-Methoxy-2-propyl acetate 100 ppm TWAAIHA WEEL
Toluene 200 ppm TWA, 300 ppm Ceiling OSHA PEL
50 ppm TWA skin ACGIH TLV
150 ppm TWA OSHA PEL
n-Butyl Acetate
150 ppm TWA, 200 ppm STEL ACGIH TLV
0.05 mg/m3 TWA OSHA PEL
Lead Chromate Molybdate Sulfate
0.05 mg/m3 TWA ACGIH TLV
0.5 mg/m3 TWA OSHA PEL
Antimony Trioxide
0.5 mg/m3 TWA ACGIH TLV
100 ppm TWA OSHA PEL
Xylenes
100 ppm TWA, 150 ppm STEL ACGIH TLV
3.5 mg/m3 TWA OSHA PEL
Carbon Black
3.5 mg/m3 TWA ACGIH TLV
15 mg/m3 TWA OSHA PEL
Titanium Dioxide
10 mg/m3 TWA ACGIH TLV
Naphtha None Established
Aromatic Naphtha None Established
100 ppm TWA OSHA PEL
n-Butyl Alcohol
20 ppm TWA ACGIH TLV
0.05 mg/m3 TWA OSHA PEL
Lead
0.05 mg/m3 TWA ACGIH TLV
0.5 mg/m3 TWA OSHA PEL
Barium
0.5 mg/m3 TWA ACGIH TLV
0.05 mg/m3 TWA OSHA PEL
Lead Sulfate
0.05 mg/m3 TWA ACGIH TLV
0.05 mg/m3 TWA OSHA PEL
Lead Chromate
0.05 mg/m3 TWA ACGIH TLV as Pb
0.012 mg/m3 TWA ACGIH TLV as Cr
5 mg/m3 TWA OSHA PEL (respirable)
Graphite
2 mg/m3 TWA ACGIH TLV (respirable)
100 ppm TWA OSHA PEL
Isobutyl Alcohol
50 ppm TWA ACGIH TLV
200 ppm TWA OSHA PEL
Methyl Ethyl Ketone
200 ppm TWA, 300 ppm STEL ACGIH TLV
500 ppm TWA OSHA PEL
Naphtha
Page 3 of 6
MATERIAL SAFETY DATA SHEET
100 ppm TWA ACGIH TLV
1,2,4-Trimethylbenzene 25 ppm TWA ACGIH TLV
Ventilation: Use only with adequate ventilation. For operations where the occupational exposure limit may be
exceeded, mechanical ventilation such as local exhaust may be needed to maintain exposure levels below applicable
limits. Use explosion-proof equipment where required.
Respiratory Protection: For operations where the occupational exposure limit may be exceeded, a NIOSH approved
organic vapor respirator with a high efficency particulate prefilter or supplied air respirator is recommended.
Equipment selection depends on contaminant type and concentration, select in accordance with OSHA 1910.134, ANSI
Z88.2 and good industrial hygiene practice. For firefighting, use self-contained breathing apparatus.
Skin Protection: Impervious gloves and protective clothing are recommended for operations which may result in skin
contact. Apron and gloves should be constructed of neoprene rubber or nitrile rubber. No specific
permeation/degradation testing has been conducted for protective clothing for this product. Recommendations are
based on infrequent contact with the product. For frequent contact or total immersion, contact a manufacturer of
protective clothing for appropriate selection information.
Eye Protection: Wear chemical safety goggles and/or faceshield to prevent eye contact.
Other Protective Equipment: Suitable washing and eye flushing facilities should be available in the work area.
Contaminated clothing should be removed and laundered before re-use.
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Appearance and Odor: Viscous liquid with a solvent odor.
pH: Not applicable Specific Gravity: 1.028
Boiling Point: 172-417癋 Melting Point: Not applicable
Vapor Pressure: 9.4 mmHg Water Solubility: 1.2%
Vapor Density: Heavier than air Evaporation Rate: 124 (BuAc=100)
Flash Point: 28癋 (7癈) pmcc Flammable Limits:
LEL: 1.5%
UEL: Not available
Solids by Weight: 19-67% Volatiles by volume: 51-85%
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable: X Unstable:
Incompatibility/Conditions to Avoid: Avoid strong oxidizing agents, bases and acids. Keep away from heat,
sparks, flames and other sources of ignition.
Hazardous Decomposition Products: Combustion will produce carbon dioxide, carbon monoxide, hydrocarbons,
oxides of lead, chromium, molybdenum and sulfur.
Hazardous Polymerization: May Occur: Will not occur: X
SECTION 11: TOXICOLOGICAL INFORMATION
Potential Health Effects:
Eye: May cause severe irritation with redness, pain and tearing. Corneal damage is possible.
Page 4 of 6
MATERIAL SAFETY DATA SHEET
Skin: May cause irritation and possible allergic reaction. May be harmful if absorbed through the skin.
Inhalation: Breathing vapors or mists may cause irritation of the mucous membranes and upper respiratory tract.
Excessive overexposure may cause headache, dizziness, drowsiness, depressed respiration and heart rate, heart
rhythm irregularities, shortness of breath, unconsciousness or death. Inhalation of mist or dust from sanding,
drilling, etc. surfaces coated with this product may result in lead poisoning with symptoms similar those described
under ingestion.
Ingestion: May be harmful or fatal if swallowed. May cause gastrointestinal irritation, nausea, vomiting, abdominal
pain and diarrhea. Aspiration into the lungs during swallowing or vomiting may cause serious lung damage which
may be fatal. This product contains lead. Lead poisoning is characterized by metallic taste in the mouth, loss of
appetite, indigestion, nausea, vomiting, constipation, abdominal cramps, sleep disturbance, fatigue. Dried film of
this product may be harmful if chewed or swallowed.
Chronic Hazards: Prolonged or repeated inhalation of the solvents in this material may result in liver, kidney and
permanent brain and nervous system damage. Intentional misuse of this product by concentrating and inhaling
vapors may be fatal. Overexposure to lead compounds adversely affects blood, blood forming organs, kidneys,
liver, central nervous system, reproductive system and causes harm to the developing fetus. This product contains
hexavalent chromium compounds. Exposure to hexavalent chromium may cause cancer. This product contains
antimony trioxide. Inhalation of antimony trioxide has been associated with effects on the blood, kidneys and liver
and an increased risk of lung cancer. Methyl ethyl ketone has been shown to cause toxic effects on the developing
fetus in laboratory animals. Toluene has been found to cause adverse fetal effects in laboratory animals and in
humans intentionally inhaling toluene. Xylene has been found to cause adverse effects on the developing fetus at
doses that were toxic to the mother.
Carcinogen Status: Hexavalent chromium compounds are classified by IARC and NTP as known human
carcinogens. Lead and inorganic lead compounds are classified by IARC as possibly carcinogenic to humans (group
2B) and by NTP as reasonably anticipated to be a carcinogen. Ethylbenzene, antimony trioxide and carbon black are
classified by IARC as possibly carcinogenic to humans (group 2B).
Medical Conditions Aggravated by Exposure: Persons with pre-existing skin, nervous system, liver, kidney,
respiratory and cardiovascular disorders may be at increased risk of exposure.
SECTION 12: ECOLOGICAL INFORMATION
No data available at this time.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste from this product may be classified as hazardous waste. Dispose in accordance with all local, state and
federal regulations.
SECTION 14: TRANSPORT INFORMATION
DOT Shipping Decsription: Paint, 3, UN1263, II
SECTION 15: REGULATORY INFORMATION
Federal Regulations
OSHA: Hazardous by definition of Hazard Communication Standard (29 CFR 1910.1200). Category: Flammable,
Irritant, Target Organ Effects, Carcinogen, Sensitizer
CERCLA 103 Reportable Quantity: Releases of this product in excess of the reportable quantity of 33 lbs (based on lead and lead
sulfate ?10 lb RQ) are reportable to the National Response Center. Many states have more stringent reporting requirements. Report
spills and other releases as required under federal, state and local regulations.
Page 5 of 6
MATERIAL SAFETY DATA SHEET
SARA TITLE III:
Hazard Category for Section 311/312: Acute Health, Chronic Health, Fire Hazard
Section 313 Toxic Chemicals: This product contains the following chemicals subject to SARA Title III Section 313
Reporting requirements:
Ethylbenzene 100-41-4 1-5
Toluene 108-88-3 5-10
Lead Chromate Molybdate Sulfate 12656-85-8 1-5
Antimony Trioxide 1309-64-4 0.1-1
Xylenes 1330-20-7 10-20
n-Butyl Alcohol 71-36-3 10-20
Lead 7439-92-1 10-20
Barium 7440-39-3 1-5
Lead Sulfate 7446-14-2 5-10
Lead Chromate 7758-97-6 10-20
Methyl Ethyl Ketone 78-93-3 5-10
1,2,4-Trimethylbenzene 95-63-6 1-5
Section 302 Extremely Hazardous Substances (TPQ): None
EPA Toxic Substances Control Act (TSCA) Status: All of the components of this product are listed on the TSCA
inventory.
STATE REGULATIONS:
California Proposition 65: This product contains chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm:
INTERNATIONAL REGULATIONS
Canadian WHMIS Classification: Class B2 Flammable Liquid, Class D-2-A (Very Toxic Material causing other
toxic effects).
This product has been classified in accordance with the hazard criteria in the CPR and the MSDS contains all the
information required by the CPR.
Canadian CEPA Status: All of the components of this product are listed on the Canadian DSL.
NFPA RATING: Health = 2 Fire = 3 Reactivity = 0
HMIS RATING: Health = 2* Fire = 3 Reactivity = 0
While the information set forth herein is believed to be accurate as of the date hereof, the Company makes no
warranty or guarantee, express or implied, and disclaims all liability arising out of the use of this information.
Page 6 of 6
|