Polybrominated Flame Retardants
Gazette
Commonwealth
of Australia
No. C 10, Tuesday, 5 October 2004
CHEMICAL
Published by the Commonwealth of Australia
ISSN 1035-9877
The Industrial Chemicals (Notification and Assessment) Act 1989 (the Act) commenced on
17 July 1990. As required by Section 5 of the Act, a Chemical Gazette is published on the
first Tuesday in any month or on any days prescribed by the regulations.
CONTENTS
SPECIAL NOTICES
1 ADDENDUM-SPECIAL GAZETTE PUBLISHED 16 AUGUST 2004- 5
LRCC
2 INFORMATION TO IMPORTERS OF INDUSTRIAL CHEMICALS 6
3 CHANGES TO THE NICNAS HANDBOOK FOR NOTIFIERS 8
4 POLYBROMINATED FLAME RETARDANTS - CALL FOR 9
INFORMATION
NEW CHEMICALS
SUMMARY REPORTS
15
5 STD/1067 POLY(OXY-1-2-ETHANEDIYL), ALPHA,
ALPHA',-[1,4-DIMETHYL-1,4-BIS (3-
METHYLBUTYL)-2-BUTYNE-1,4-
DIYL]BIS[OMEGA-HYDROXY-
6 STD/1099 PROMIDIUM IS 18
7 STD/1112 W-663 20
8 LTD/1129 SODIUM PEG-7 OLIVE OIL CARBOXYLATE 22
9 LTD/1135 POLYMER IN PLIOGRIP 24
10 LTD/1152 POLYMER IN DISPERBYK-2001 27
11 LTD/1154 B-21825 29
12 LTD/1156 DOW CORNING 7-6030 QUATERNARY 31
AMMONIUM FUNCTIONAL SILICONE
13 EX/58 POLYMER IN DOW CORNING 9040 SILICONE 34
ELASTOMER BLEND
14 PLC/324 POLYESTER ALKYD-25 37
15 PLC/423 RESIN COMPONENTS OF LEXAN SLX 39
GRADES
16 PLC/448 POLYMER IN NALCO 98 AUS047 41
17 PLC/473 ARISTOFLEX AVC 43
18 PLC/474 POLYMER IN POLYURETHANE DISPERSION 45
145049
19 PLC/490 POLYMER IN OPTIFLO M2600/M2600VF 47
20 PLC/493 TOPAS 50
21 PLC/495 S-9974 52
22 ACCESS TO FULL PUBLIC REPORT 54
PERMITS ISSUED
23 LOW VOLUME CHEMICAL PERMITS 55
24 COMMERCIAL EVALUATION CATEGORY PERMITS 56
25 EARLY INTRODUCTION PERMITS 57
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES
58
26 NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES FIVE
YEARS AFTER ISSUING OF ASSESSMENT CERTIFICATES
27 NOTICE OF AMENDMENTS TO THE AUSTRALIAN INVENTORY 60
OF CHEMICAL SUBSTANCES
61
28 NOTICE OF CHEMICALS ELIGIBLE FOR IMMEDIATE LISTING
ON THE AUSTRALIAN INVENTORY OF CHEMICAL
SUBSTANCES AFTER ISSUING OF ASSESSMENT
CERTIFICATES
5
1 ADDENDUM-SPECIAL GAZETTE PUBLISHED 16 AUGUST 2004-LRCC
There was an error on page 7 of the above Gazette. Correct text is included below:
Non-cosmetic chemical (amended)
The volume restriction for the exemption of non-cosmetic chemicals which pose no
unreasonable risk to occupational health, public health or environment, has increased from 10
to 100kg/annum [subpara. 21(4)(b)(ii)]. Advice to NICNAS prior to introduction is optional
and introducers of chemicals in this category wishing to advise NICNAS should fill out Form
21-4a and return it to NICNAS.
There is a new requirement for the introducer to keep records relating to occupational health
and safety, public health matters and the environmental effects of the chemical for five years.
Annual reporting requirements for this exemption category commence for the registration
year 1 September 2004, with the first report required by 28 September 2005. [s.21AA of the
Act].
Cosmetic chemical <10kg (amended)
Introducers of cosmetic chemicals which pose no unreasonable risk to occupational health,
public health or environment, in quantities of less than 10kg/annum, are no longer required to
notify NICNAS prior to introduction.
The criteria for the cosmetic chemical and the five-year record keeping requirement remain
unchanged. Annual reporting requirements for this exemption category commence for the
registration year 1 September 2004, with the first report required by 28 September 2005.
[s.21AA of the Act].
Cosmetic chemical >10kg but <100kg (amended)
The volume restriction for the exemption of cosmetic chemicals which pose no unreasonable
risk to occupational health, public health or environment, has increased from 10 to
100kg/annum [subpara. 21(4)(b)(i)]. Introducers of the chemical must notify NICNAS of the
introduction in writing (Form 15) and provide the Material Safety Data Sheet (MSDS)
relevant to the chemical or product containing the chemical and a copy of the label attached
to the packaging of the chemical or product containing the chemical.
The criteria for the cosmetic chemical and the five-year record keeping requirement remain
unchanged. Annual reporting requirements for this exemption category commence for the
registration year 1 September 2004, with the first report required by 28 September 2005.
[s.21AA of the Act].
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
6
2 INFORMATION TO IMPORTERS OF INDUSTRIAL CHEMICALS
NICNAS has received a number of enquiries from importers and Customs Brokers about
relevant tariff classifications to goods containing industrial chemicals. The Table below
shows a typical list of tariff classifications that may fall within the scope of the NICNAS
Registration requirements. Importers should note that they should not limit themselves to
these import classifications as some industrial chemicals are imported under chapters not
listed below:
For more information on these chapters see the Australian Customs Service website at
http://www.customs.gov.au/site/page.cfm?u=4273.
Chapter Reference Number Description
Animal or vegetable fats and oils and their cleavage
1505, 1518 to 1522
15
products; prepared edible fats; animal or vegetable waxes
inclusive
Salt; sulphur; earths and stone; plastering materials; lime
All
25
and cement
All Ores, slag and ash
26
Mineral fuels, mineral oils and products of their
All except 2701,
27
distillation; bituminous substances; mineral waxes
2702, 2703, 2709
Inorganic chemicals; organic or inorganic compounds of
All except 2844,
28
precious metals, of rare-earth metals, of radioactive
2845
elements or of isotopes
All except 2935,
29
Organic chemicals
2936, 2937, 2940,
2941
Tanning or dyeing extracts; tannins and their derivatives;
All
32
dyes, pigments and other colouring matter; paints and
varnishes; putty and other mastics; inks
Essential oils and resinoids; perfumery, cosmetic or toilet
All
33
preparations
Soap, organic surface-active agents, washing
All except 3406
34
preparations, lubricating preparations, artificial waxes,
prepared waxes, polishing or scouring preparations,
candles and similar articles, modelling pastes, "dental
waxes" and dental preparations with a basis of plaster
Albuminoidal substances; modified starches; glues;
All
35
enzymes
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
7
Explosives; pyrotechnic products; matches; pyrophoric
All except 3603
36
alloys; certain combustible preparations
Photographic or cinematographic goods
3707 only
37
3707- Chemical preparations for photographic uses
(other than varnishes, glues, adhesives and similar
preparations), unmixed products for photographic uses,
put in measured portions or put up for retail sale in a
form ready for use
All Miscellaneous chemical products
38
3901 to 3914
39
Plastics and articles thereof
inclusive
4001 and 4002 only Rubber and articles thereof
40
Pulp of wood or of other fibrous cellulosic material;
47
All except 4707
recovered (waste and scrap) paper or paperboard
Miscellaneous manufactured articles
9608, 9612, 9613
96
only
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
8
3 CHANGES TO THE NICNAS HANDBOOK FOR NOTIFIERS
The Handbook for Notifiers has been updated on the NICNAS website to reflect the new
arrangements following the introduction of the Industrial Chemicals (Notification and
Assessment) Amendment (Low Regulatory Concern Chemicals ) Act 2004 (LRCC
Amendment Act).
The Handbook is a guide to importers, manufacturers and exporters of industrial chemicals in
Australia. It outlines their obligations under the Industrial Chemicals (Notification and
Assessment) Act 1989, as well as the assessment and notification procedures and other
information relevant to industrial chemicals regulation.
For further enquiries about the Handbook for Notifiers contact Hana Hamdan (Team Leader,
Innovation and Compliance) on 02 8577 8855 or email to comply@nicnas.gov.au.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
9
4 POLYBROMINATED FLAME RETARDANTS - CALL FOR
INFORMATION
The Director of the National Industrial Chemicals Notification and Assessment Scheme
(NICNAS) is seeking information under section 48 of the Industrial Chemicals (Notification
and Assessment) Act 1989 (the Act) on polybrominated flame retardants (PBFRs).
The information sought on these chemicals is:
? Quantities imported and/or manufactured;
? Products imported containing the chemical and quantities of chemical in the products;
? Uses of the chemical or the products containing the chemical; and
? Alternatives or substitutes currently being used
The notice is directed to all persons who have manufactured or imported one or more of the
PBFRs or products containing PBFRs in the last 12 months. Any other persons with
information on these chemicals including users, past importers or manufacturers are also
encouraged to provide information on the uses of and alternatives available for these
chemicals to the Director.
The data provided will be used to update the information currently held by NICNAS and
determine further regulatory activity.
While the table below may not cover all the PBFRs in use in Australia it can be used as
a guide.
Polybrominated Flame Retardants CAS No
1,2-bis(2,4,6-tribromophenoxy)ethane 37853-59-1
1,4-Bis(pentabromophenoxy)tetrabromobenzene 58965-66-5
59447-57-3
2-propenoic acid (pentabromophenyl)methyl ester,
homopolymer
3,4,5,6-Tetrabromophthalic anhydride, ethylene 77098-07-8 /
glycol, propylene oxide reaction products 20566-35-2
Bis(2,3-dibromopropyl) phosphate 5412-25-9
Decabromodiphenyl ether 1163-19-5
Disodium tetrabromophthalate 25357-79-3
Hexabromocyclododecane 25637-99-4
Hexabromodiphenyl ether 36483-60-0
Nonabromodiphenyl ether 63936-56-1
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
10
Octabromodiphenyl ether 32536-52-0
Pentabromodiphenyl ether 32534-81-9
71342-77-3
Phosgene-tetrabromobisphenol A polymer bis(2,4,6-
tribromophenyl) ester
125997-20-8
Phosphoric acid, mixed 3-bromo-2,2-dimethyl propyl
and 2-chloroethyl esters
Polymer of tetrabromobisphenol A, phosgene, phenol 94334-64-2
Polystyrene, brominated 88497-56-7
Tetrabromobisphenol A 79-94-7
Tetrabromobisphenol A bis(2,3-dibromopropyl) ether 21850-44-2
68928-70-1
Tetrabromobisphenol A, 2,2-bis[4-(2,3-
epoxypropyloxy)dibromophenyl]propane polymer
Tetrabromodiphenyl ether 40088-47-9
Tribromodiphenyl ether 49690-94-0
Tris(tribromoneopentyl) phosphate 19186-97-1
Responses on the chemicals are required on the attached form. A separate form should be
completed for each chemical. The due date for responses is 17 November 2004.
The penalty for non-compliance with this notice is up to $33,000. In accordance with Section
50 of the Act, the information may be accompanied by an application that some or all of the
information provided should be treated as `exempt information'. Application forms may be
obtained from Ms Virginia Parish on 02 8577 8893 or via the NICNAS website at
http://www.nicnas.gov.au/forms/files/form3.doc.
Polybrominated Flame Retardants (PBFRs) have attracted much interest internationally and
nationally given the human health and environmental concerns of some chemicals within this
group. NICNAS conducted a preliminary assessment on polybrominated flame retardants as a
group and published a report (Priority Existing Chemical Assessment Report No. 20) in 2001.
The report can be accessed at
http://www.nicnas.gov.au/publications/CAR/PEC/PEC20/PEC20index.asp. Recent
information on some of these chemicals has lead to regulatory activities overseas and
considerable interest nationally.
Polybrominated flame retardants have widespread use in numerous household and industrial
items such as printed circuit boards, polystyrene and other plastics. This large number of
dispersive uses provides many ways for PBFRs to enter the environment. Some
polybrominated flame retardants are persistent, lipophilic and bioaccumulative, therefore,
adversely impact the environment. Some PBFRs cause carcinogenicity, endocrine disruption
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
11
and reproductive effects. Hence, current Australian use information is required to put the
hazard data on PBFRs in perspective.
Further information can be obtained from Dr Janith Wickramaratna (Tel: 02 8577 8846;
email: janith.wickramaratna@nicnas.gov.au).
Completed forms should be sent to Ms Virginia Parish
Existing Chemicals
NICNAS
GPO Box 58
Sydney NSW 2001
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
12
RESPONSE TO SECTION 48 NOTICE ?POLYBROMINATED FLAME
RETARDANTS
Please use a separate form for each chemical.
Company Name:
Address:
Contact name:
Phone Number: Fax Number:
Details of Chemical
Chemical Name:
Product or Trade Name:
Chemical Abstract Services Number (CAS No.):
1. Do you manufacture the above chemical (Please circle) Y/N
If yes, please provide an estimate of the quantity you manufacture (tonnes/year)
Tonnes/year:
2. Do you import the chemical? Y/N
If yes, please provide an estimate of the quantities of chemical you import (tonnes/year)
Tonnes/year:
3. Do you import products (mixtures) containing this chemical? Y/N
Please indicate the product(s) you import containing the chemical and the total tonnage of chemical in each
product:
Name of Product Tonnes chemical/year
(Description of Product)
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
13
4. What are the uses of the chemical/products?
5. Do you manufacture or formulate products containing this chemical? Y/N
Please indicate the product(s) you manufacture or formulate containing the chemical and the total tonnage of
chemical in each product:
Name of Product Tonnes chemical/year
(Description of Product)
6. Do you use this chemical other than for manufacturing products
(eg. manufacturing articles)? Y/N
If yes, what types of articles are they used in?
7. What are the uses of the products manufactured/formulated by you?
8. Is this chemical available to members of the public? Y/N
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
14
Do you manufacture/import any chemicals that are used as an alternative/substitute for PBFRs? Y/N
9.
If yes please provide
Name of Chemical Quantities
Information collected by NICNAS may be provided to State, Territory or Commonwealth regulatory agencies
for the purposes of monitoring compliance under relevant legislation. All information collected is treated in
accordance with strict confidentiality guidelines and in compliance with the Privacy Act 1988.
Further information can be obtained from Dr Janith Wickramaratna (Tel: 02 8577 8846; email:
janith.wickramaratna@nicnas.gov.au).
Is your company a small business with less than 20 employees? YES NO
If yes, please provide an estimate of the time taken to complete this form:
hrs mins
Thank-you. Please send the completed form to: Ms Virginia Parish
Existing Chemicals
NICNAS
GPO Box 58
Sydney NSW 2001
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
15
5 PUBLICATION SUMMARY REPORT
Poly(oxy-1,2-ethanediyl), alpha, alpha', -[1,4-dimethyl-1,4-bis (3-methylbutyl)-2-
butyne-1,4-diyl]bis[omega-hydroxy-
Summary Report
Reference No: STD/1067
Swift and Company Ltd (ABN 44 000 005 578), of Level 1, 372 Wellington Rd, Mulgrave,
Victoria, 3170 and 3M Australia Pty Ltd (ABN 90 000 100 096), of 2-74 Dunheved Circuit,
St Marys, 2760 have submitted a standard notification statement in support of their
application for an assessment certificate for Poly(oxy-1,2-ethanediyl), , ', -[1,4-dimethyl-
1,4-bis (3-methylbutyl)-2-butyne-1,4-diyl]bis[-hydroxy-. The notified polymer is intended
to be used as a non-ionic wetting agent for high performance waterborne applications such as
coatings, inks and adhesives. One to three tonnes of the notified polymer will be imported per
annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the assumption that analogue data are acceptable and indicative of toxicity of the
notified polymer, the notified polymer is classified as hazardous under the NOHSC Approved
Criteria for Classifying Hazardous Substances. The classification and labelling details are:
R41 Risk of Serious Damage to Eyes
Occupational Health and Safety
Use as a clear coat component
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Use as fountain solution concentrate component and other potential uses
There is Moderate Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
Use as a clear coat component and Use as fountain solution concentrate component
There is Negligible Concern to public health based on its reported use pattern.
Other potential uses
There is No Significant Concern to public health based on its reported use pattern.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its PEC/PNEC
ratio and reported use pattern.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
16
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? Use the following risk phrases for products/mixtures containing the notified polymer:
- > 10%: R41
- 5% < concentration < 10%: R36
Control Measures
Occupational Health and Safety
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer as introduced.
- Avoid contact with eyes
- Avoid splashes and spills
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer as introduced:
- Splash-proof goggles, chemical resistant industrial clothing and impermeable gloves;
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
? The following control measures should be implemented by end users to minimise
environmental exposure during use of the notified polymer:
- Do not allow material or contaminated packaging to enter drains, sewers or water
courses.
Disposal
? The notified polymer should be disposed of in a landfill in compliance with federal,
state and local authorities. Waste product may also be incinerated in an approved
combustion system. Careful measures should be undertaken to avoid release of the
notified polymer to the sewer system and watercourses.
Emergency procedures
? Spills/release of the notified polymer should be handled by stopping the leak/spill if
possible, reducing vapour spreading with a water spray and constructing a dike to
prevent water flow. If recovery is not feasible admix with dry soil, sand or non-
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
17
reactive adsorbent and place in an appropriate chemical waste container. Transfer to
containers by suction, preparatory for later disposal. Flush area with water spray. For
large spills, recover spilled material with a vacuum truck.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is included in products at a percentage >5%
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
18
6 PUBLICATION SUMMARY REPORT
Promidium IS
Summary Report
Reference No: STD/1099
Uniqema Australia Pty Ltd (ABN 00018084) of Level 37, 101 Collins St Melbourne VIC
3000 and Symex Holding Pty Ltd (ABN 29 091 035 353) of 14 Woodruff St Port Melbourne
VIC 3207 have submitted a standard notification statement in support of their application for
an assessment certificate for Promidium IS. The notified chemical is intended to be used as a
cleansing agent, solubiliser, consistency agent and foam booster in personal care products and
industrial cleaning agents. Personal care products will be either imported preformulated or
formulated in Australia by batch processes. Less than 10 tonnes of the notified chemical will
be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data, the notified chemical is classified as a hazardous substance in
accordance with the NOHSC Approved Criteria for Classifying Hazardous Substances in
terms of skin and eye irritation.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as described.
Environmental Effects
On the basis of the PEC/PNEC ratio, the notified chemical is not considered to pose a risk to
the environment based on its reported use pattern and estimated volumes.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
[health, environmental and physico-chemical] hazard classification for the notified
chemical:
? R36 Irritating to eyes
? R38 Irritating to skin
? Use the following risk phrases for products/mixtures containing the notified chemical:
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
19
? 20%: R36 Irritating to eyes
? 20%: R38 Irritating to skin
Control Measures
Occupational Health and Safety
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced:
- Impervious gloves
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
? The following control measures should be implemented by reformulator to minimise
environmental exposure during reformulation of the notified chemical:
- Process areas should be bunded with all drains leading to a treatment plant or
collection point
Disposal
? The notified chemical should be disposed of to landfill.
Emergency procedures
? Spills/release of the notified chemical should be contained, collected and placed in
sealable labelled container. The material should be reused if not contaminated. If
contaminated then it should be disposed of to landfill.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
20
7 PUBLICATION SUMMARY REPORT
W-663
Summary Report
Reference No: STD/1112
Brother International (Aust.) Pty Ltd (ACN 17 001 393 835) of 7 Khartoum Road North
Ryde NSW 2113 has submitted a standard notification statement in support of their
application for an assessment certificate for W-663. The notified chemical is intended to be
used as an additive in toner used for printing. The toner containing the notified chemical will
be imported in toner cartridges for electrophotocopying machines or electrophotographic
printers. Cartridges are replaced by removal of sealing tape and insertion into the machine or
printer. Less than three tonnes of the notified chemical will be imported per annum for each
of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data, the notified chemical is not classified as a hazardous substance in
accordance with the NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as described.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
No special precautions are required for the notified chemical when used at low quantities in
a toner in cartridges in electrophotocopying machines or electrophotographic printers.
However, in the interests of good occupational health and safety, the following guidelines
and precautions should be observed for use of toners containing the notified chemical:
? Avoid contact with skin and eyes.
? Avoid breathing dust
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
21
? Avoid generation of dust. Photocopiers and printers should be located in well
ventilated areas. The NOHSC Exposure Standard of 10 mg/m3 TWA for nuisance
dust should be maintained in the workplace.
? Service personnel should wear cotton or disposable gloves when replenishing toner
and servicing copying machines and printers.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
Environment
Disposal
? Empty toner cartridges containing the notified chemical should be disposed of to
landfill.
? Do not dispose the notified chemical into sewers or water bodies.
Emergency procedures
? Spills/release of the notified chemical should be handled by sweeping up and
discarding in to a waste container.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
22
8 PUBLICATION SUMMARY REPORT
Sodium PEG-7 Olive Oil Carboxylate
Summary Report
Reference No: LTD/1129
Unilever Australia Limited (ABN 66 004 050 828) of 219 North Rocks Road North Rocks
NSW 2151 has submitted a limited notification statement in support of their application for
an assessment certificate for the chemical "sodium PEG-7 olive oil carboxylate". The notified
chemical is intended for use as an anionic surfactant at 1.2% in a facial toner product. About
300 kg of the notified chemical will be imported per annum for each of the first five years,
initially in final consumer packages and then as a 35% aqueous solution (Olivem 400) for
local formulation.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data there is insufficient information to substantiate that the notified
chemical is not a hazardous substance. However, Olivem 400 (35% notified chemical) is not
likely to be classified as hazardous under the NOHSC Approved Criteria for Classifying
Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used in the proposed manner.
Environmental Effects
On the basis of the widespread and low use level, the chemical is not considered to pose a
risk to the environment at the proposed import volume.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical as introduced in a 35% solution:
- Enclosed and automated processes at the blending and packaging sites;
- Adequate ventilation for the plant operators and local exhaust ventilation for quality
control personnel.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical as introduced in the
lubricant additive package:
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
23
- Adequate training for staff in handling surfactant components;
- Implementation of general health surveillance and monitoring programs as required.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced in
the lubricant additive package:
- Industrial standard protective clothing and gloves;
- Safety glasses with side-shields/chemical goggles;
- Vapour respirators if required.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? The notified chemical should be disposed of by recovering the product if possible and
disposing to landfill.
Emergency procedures
? Spills/release of the notified chemical should be prevented from spreading or entering
into drains, ditches or rivers by using sand, earth or other appropriate barriers. Small
spills may be diluted with water, whilst larger spills should be adsorbed with inert
material (sand or vermiculate) and disposed of in accordance with local, state and
federal authorities.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
24
9 PUBLICATION SUMMARY REPORT
Polymer in Pliogrip Adhesives
Summary Report
Reference No: LTD/1135
Ashland Pacific Pty Ltd (ACN 000 075 641) of Sir Thomas Mitchell Road, Chester Hill
NSW 2162 has submitted a limited notification statement in support of their application for
an assessment certificate for Polymer in Pliogrip Adhesives. The notified polymer is intended
to be used as a component of an adhesive for heavy vehicles. The adhesive will be imported
in cartridges containing two variants of the notified polymer, isocyanate-rich and polyol-rich,
which are mixed before being extruded onto the substrate. Less than 10 tonnes of the notified
polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified polymer is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances. However, the isocyanate-
rich component of the adhesive is classified as hazardous. The classification and labelling
details are:
R20 - Harmful by inhalation,
R36/37/38 - Irritating to eyes, respiratory system and skin and
R42/43 - May cause sensitisation by inhalation and skin contact.
Occupational Health and Safety
There is Moderate Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as indicated.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
The following recommendations relate to the isocyanate-rich notified polymer containing
approximately 50% excess isocyanate. Although the adhesive contains the notified polymer
at a low level (7%), in the absence of certain knowledge of likely atmospheric concentrations
of isocyanate in the workplace and in view of the serious consequences of isocyanate-induced
respiratory sensitisation, a conservative approach to risk management should be taken.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
25
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to
minimise occupational exposure to the notified polymer in Pliogrip
adhesives:
- Good general ventilation and local exhaust ventilation where practicable.
? Employers should ensure that the following personal protective
equipment is used by workers to minimise occupational exposure to the
notified polymer in Pliogrip adhesives:
- Supplied air respiratory protection and protective clothing, gloves and
footwear impervious to isocyanate-containing compounds. The open
points at the interface between different forms of protective clothing
should be sealed.
Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.
? Atmospheric or biological monitoring should be conducted by qualified
professionals to guage potential workplace atmospheric concentrations of
isocyanate during use of the notified polymer.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified
as hazardous to health in accordance with the NOHSC Approved Criteria
for Classifying Hazardous Substances, workplace practices and control
procedures consistent with provisions of State and Territory hazardous
substances legislation must be in operation.
? Preplacement and periodic medical surveillance programs should be
conducted for all workers potentially exposed to isocyanates. Emphasis
should be placed on pre-existing respiratory and/or allergic conditions
and lung function tests.
Environment
Disposal
? The notified chemical should be disposed of by landfill or incineration
Emergency procedures
? Absorb with an inert material and put the spilled material in an
appropriate waste disposal. Finish cleaning by spreading water on the
contaminated surface and allow to evacuate through the sewer system.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
26
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
27
10 PUBLICATION SUMMARY REPORT
Polymer in Disperbyk-2001
Summary Report
Reference No: LTD/1152
Nuplex Industries (Aust) Pty Ltd (ABN: 25 000 045 572) of 49-61 Stephen Road, Botany
NSW 2019 and PPG Industries Australia Pty Ltd (ABN: 82 055 500 939) of McNaughton
Road, Clayton, VIC 3168 have submitted a limited notification statement in support of their
application for an assessment certificate for Polymer in Disperbyk-2001. The notified
polymer is intended to be used as a wetting and dispersing additive for solvent based coatings
and pigment concentrates. It will be used at below 6% in paint formulations, mostly for
automotive use. Up to five tonnes of the notified polymer will be imported per annum for
each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data, the notified polymer is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as described in the notification.
Environmental Effects
The notified polymer is not considered to pose a risk to the environment based on its reported
use pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified polymer:
- Enclosed spray paint application system for industrial use.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
as diluted for use in the products:
- Protective gloves,
- safety glasses or goggles,
- half-facepiece respirator and
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
28
- industrial clothing
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
? The following control measures should be implemented by end users to minimise
environmental exposure during use of the notified polymer:
- Do not pour leftover paint or cleaning solvent down the drain.
Disposal
? Wastes generated during industrial application should be disposed of through a
licensed waste contractor.
? Keep unwanted paint in sealed containers for disposal via special chemical waste
collections. Empty paint containers should be left open in a well-ventilated area to dry
out. When dry, recycle steel containers via steel can recycling programs.
Emergency procedures
? Spills/release of the notified chemical should be soaked up with inert absorbent
material and disposed of in accordance with State regulations. Do not allow spills to
enter drains.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
If the use pattern changes leading to a significant increase in the potential for aquatic
exposure, then ecotoxicity data for fish, daphnia and algae should to be submitted for
assessment.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
29
11 PUBLICATION SUMMARY REPORT
B-21825
Summary Report
Reference No: LTD/1154
Kodak Australasia Pty Ltd (ABN 49 004 057 621) of 173 Elizabeth Street, Coburg, VIC 3058
has submitted a limited notification statement in support of their application for an
assessment certificate for B-21825. The notified chemical is intended to be used as a
component of photographic paper. The chemical will be imported and used in the
manufacture of photographic paper at the notifier's plant. Less than one tonne of the notified
chemical will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is not classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical:
- For formulation, local exhaust ventilation should be used when handling the notified
chemical in powder form.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical as introduced and in
the emulsion formulation and application processes:
- In handling the notified chemical, avoid spills and dust generation.
- In handling the notified chemical, minimise the potential for ingestion through good
personal hygiene.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
30
- In handling the emulsion formulation, avoid spills, splashes or aerosol generation that
would increase exposure.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced and
in the emulsion formulation and application processes:
- Respiratory protection if exposure to dust is likely.
- Gloves
- Protective clothing
- Safety eye protection
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Disposal
? Dispose of wastes containing the notified chemical according to local jurisdiction
waste disposal regulations. Residual chemical retained in emptied containers and in
dust collection filters should be treated as prescribed waste and disposed of to secure
landfill. Follow label warnings even after container is emptied.
Emergency procedures
? Spills/release of the notified chemical should be collected by shovelling into suitable
containers for disposal. Avoid dust formation. Clean surface thoroughly to remove
residual contamination.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Subsection 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical.
or
Under Subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
31
12 PUBLICATION SUMMARY REPORT
Dow Corning 7-6030 Quaternary Ammonium Functional Silicone
Summary Report
Reference No: LTD/1156
Dow Corning Australia Pty Ltd (ABN 36 008 444 166) of 3 Innovation Road Macquarie
University Research Park North Ryde NSW 2113 has submitted a limited notification
statement in support of their application for an assessment certificate for Dow Corning 7-
6030 Quaternary Ammonium Functional Silicone. The notified polymer is intended to be
used as a component of hair care products. The notified polymer will be imported as a
polymer concentrate at >90% and will be stored at the notifier's warehouse prior to
distribution to local hair care product formulators. Alternatively, the notified polymer will be
imported as formulated hair care products containing <1% notified polymer. Up to 10 tonnes
of the notified polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data, the notified polymer is classified as a hazardous substance in
accordance with the NOHSC Approved Criteria for Classifying Hazardous Substances. The
classification and labelling details are:
R36/38 ?Irritating to eyes and skin; and
R43 ?May cause sensitisation by skin contact.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used as a component of hair care
products.
Environmental Effects
On the basis of the PEC/PNEC ratio, the polymer is not considered to pose a risk to the
environment based on its reported use pattern.
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified polymer:
- R36/38 ?Irritating to eyes and skin; and
- R43 ?May cause sensitisation by skin contact.
? Use the following risk phrases for products/mixtures containing the notified polymer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
32
- 20%: R36/38 - Irritating to eyes and skin.
- 1%: R43 - May cause sensitisation by skin contact.
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified polymer as introduced:
- Local exhaust ventilation during transfer and mixing operations
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified polymer as introduced:
- During transfer operations and cleaning equipment, avoid spills and splashing.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified polymer as introduced:
- Chemical resistant gloves, safety glasses, protective clothing or equivalent when
handling the notified polymer
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? Dispose of wastes containing the notified polymer in accordance with local
jurisdiction waste management regulations.
? Do not dispose of the notified polymer to drains or natural waterways.
? Spilled notified polymer (including saturated absorbent or cleaning material) may be
hazardous as spontaneous heating may occur. Such wastes should be disposed of to
landfill or incinerated.
? Emptied finished product containers with residues of the notified chemical should be
cleaned and recycled or sent to landfill for disposal.
? Small quantities of waste/spilled formulation containing the notified chemical should
be disposed of to landfill or sewer.
Emergency procedures
? Spills/release of the notified polymer should be prevented from spreading or entering
into drains, ditches or rivers by using sand, earth or other appropriate barriers. Inform
local authorities if this cannot be prevented.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
33
? Clean up spilled quantities of notified polymer by pumping into labelled, sealable
containers. Clean up remaining materials from spill with suitable absorbent. Final
clean using steam, solvents or detergents and collect washwaters for treatment and
appropriate disposal
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
34
13 PUBLICATION SUMMARY REPORT
Polymer in Dow Corning 9040 Silicone Elastomer Blend
Summary Report
Reference No: EX/58
An Assessment Certificate for the notified polymer known by the name Polymer in DOW
CORNING 9040 Silicone Elastomer Blend was granted to Dow Corning Australia Pty Ltd
(ABN 91 008 396 245) of Macquarie University Research Park; 3 Innovation Rd, North Ryde
NSW 2113.
The Assessment Report for Polymer in DOW CORNING 9040 Silicone Elastomer Blend is
identified by the sequence number PLC/189 (Synthetic Polymer of Low Concern
Notification).
Since granting of the abovementioned Assessment Certificate, Unilever Australia Ltd (ABN
66 004 050 828) of 219 North Rocks Road North Rocks NSW 2151 has submitted a
notification statement in support of their application for an extension of the original
Assessment Certificate for Polymer in DOW CORNING 9040 Silicone Elastomer Blend.
Dow Corning Australia Pty Ltd. has agreed to this extension.
Information submitted by Unilever Australia Pty Ltd pertains to the introduction of the
notified polymer for use in as a viscosity increasing and suspending agent in moisturizing
lotions. Introduction volumes will be up to 400 kg per year, imported as the finished product.
The concentration of the chemical in final products is 7.8%.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer is of very low acute oral toxicity and low dermal toxicity. It is not a
skin irritant or a skin sensitiser, and a very slight ocular irritant. No evidence of mutagenicity
was observed in a bacterial assay. The notified polymer is not classified as a hazardous
substance in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances
Occupational Health and Safety
There is little potential for significant occupational exposure to the notified polymer in the
transport and storage of the polymer solution or the personal care products containing this
polymer, or during retail sale of the products. There will be exposure during production of the
personal care products.
During the reformulation and packaging processes, the main exposure route for the notified
polymer will be dermal. The polymer solution and final products will be viscous, and ready
formation of aerosols is not expected. The polymer is not expected to be hazardous by dermal
exposure as the high molecular weight will preclude absorption through the skin. The
engineering controls and personal protective equipment specified in the notification (local
exhaust ventilation and protective eyewear) will provide protection against the notified
polymer. No significant OHS risks are expected due to the low toxicity of the notified
polymer.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
35
Public Health
An analogous chemical to the notified polymer showed some evidence of effects on
reproduction in rats, following subcutaneous administration (Kennedy, 1976). The use of the
notified polymer at 0.1%-1.7% in personal care products means that a small amount will be
applied to the skin for each use. Likely skin application sites, such as underarms, possess
large numbers of sweat glands, and consequently there is potential for increased dermal
absorption at these sites. This is not of concern in this case, as the notified polymer is of high
molecular weight (NAMW > 15500) and is unlikely to penetrate biological membranes,
suggesting limited systemic absorption following normal use.
The low concentration and limited systemic absorption would eliminate any potential toxic
hazard from normal use of the polymer in personal care products. There will be minimal
public exposure during transport, storage and formulation into personal care products.
Based on the above information, it is considered that Polymer in DOW CORNING 9040
Silicone Elastomer Blend is unlikely to pose a significant hazard to public health when used
in the proposed manner.
Environmental Effects
Almost all of the new polymer is expected to be released to the environment as a
consequence of its use in personal care products. Most is expected to be released to the
sewer, although some may be placed directly into landfill with domestic garbage. The
polymer is not biodegradable and that portion released to the sewer (estimated as up to 37.5
tonnes per annum) will become associated with sewer sludge due to its hydrophobic nature.
Although all the polymer is expected to be released, the use pattern is such that the release
will be diffuse and at relatively low levels. For example, if all the annual import of 50
tonnes were to be released to the sewer system, assuming that each individual in Australia
produced 150 L of sewage each day, and taking the national population as 19,000,000 the
Predicted Environmental Concentration (PEC) in the sewage is estimated as 48 礸/L.
However, as indicated previously this will become associated with sludge, and this will
ultimately also be placed into landfill, although some may be incinerated. It is also expected
that around 12.5 tonnes of polymer may be directly released to the soil compartment
through disposal of partly emptied containers in domestic garbage.
Silicone polymers are stable under moist conditions, but it is expected that prolonged
residence in dry landfills would eventually degrade the polymer to landfill gases and silica,
while incineration would destroy the material, also with production of silica.
No ecotoxicity data were supplied, but silicone polymers are not known to be toxic to
aquatic organisms, and in any case the low rate of release and expected association of the
polymer with sediments would mitigate any toxic effects. The polymer is not expected to
bioaccumulate.
RECOMMENDATIONS
To minimise occupational exposure to Polymer in DOW CORNING 9040 Silicone Elastomer
Blend, the following guidelines and precautions should be observed:
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
36
Safety eyewear should be used during occupational use of the products containing the
?br>
notified polymer;
Spillage of the notified chemical should be avoided. Spillages should be cleaned up
?br>
promptly with absorbents which should then be put into containers for disposal;
Good personal hygiene should be practised to minimise the potential for ingestion;
?br>
A copy of the MSDS should be easily accessible to employees.
?br>
If products containing the notified chemical are hazardous to health in accordance
?br>
with the NOHSC Approved Criteria for Classifying Hazardous Substances,
workplace practices and control procedures consistent with State and territory
hazardous substances regulations must be in operation.
Guidance in selection of goggles may be obtained from Australian Standard (AS) 1336
(Standards Australia, 1994) and Australian/New Zealand Standard (AS/NZS) 1337
(Standards Australia/Standards New Zealand, 1992).
Secondary Notification
Under the Act, the Director of Chemical Notification and Assessment must be informed if the
polymer characteristics cease to satisfy the criteria under which it has been accepted as a
Synthetic Polymer of Low Concern, and secondary notification may be required under
subsection 64(1). The Director must be informed if any of the circumstances stipulated under
subsection 64(2) of the Act arise, and secondary notification of the notified polymer may be
required. No other specific conditions are prescribed.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
37
14 PUBLICATION SUMMARY REPORT
Polyester Alkyd 25
Summary Report
Reference No: PLC/324
Nuplex Industries (Aust) Pty Ltd (ACN 15 902 254 524) of 49-61 Stephen Road Botany
NSW 2019 has submitted a synthetic polymer of low concern (PLC) notification statement in
support of their application for an assessment certificate for Polyester Alkyd 25. The notified
polymer will be blended with styrene and performance-enhancing additives to produce a resin
binder suitable for use in fibre reinforced composite materials. 100 tonnes of the notified
polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health based on the use pattern.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
38
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
? The use of the product containing the polymer should be in accordance with the
NOHSC National Guidance Material for Spray Painting where appropriate.
Environment
? The following control measures should be implemented by the manufacturers to
minimise environmental exposure during manufacture and use of the notified
polymer:
- Do not release the resin or polymer products to sewer. Do not allow resin, polymer
products or containers to contaminate drains or waterways.
Disposal
? The notified polymer should be disposed of by release to landfill or incineration.
Emergency procedures
? Spills/release of the notified polymer should be handled by containment, and
adsorption with material such as sand. Contaminated material (including sand) should
be collected, placed into sealable labelled container and disposed of to landfill. Do
not allow to enter drains or watercourses.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
39
15 PUBLICATION SUMMARY REPORT
Resin Components of Lexan SLX grades
Summary Report
Reference No: PLC/423
General Electric Plastics Pty Ltd of 175 Hammond Road, Dandenong, Victoria 3175 has
submitted a synthetic polymer of low concern (PLC) notification statement in support of their
application for an assessment certificate for Resin components of LEXAN SLX grades. The
notified polymer is intended to be used to make plastic components for use in appliance parts.
Thirty to three hundred tonnes of the notified polymer will be imported per annum for each of
the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as a photocopier toner.
Environment Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
40
Environment
Disposal
? The notified polymer should be disposed of in landfill or by incineration in
accordance with federal, state and local regulations. Collected processing fume
condensates and incinerator ash should be tested to determine waste classification.
? Empty import bags should be disposed of to landfill with any residual polymer.
? Recycling is encouraged.
Emergency procedures
? Spills/release of the notified polymer should be handled by gathering and storing in
closed containers pending waste disposal evaluation.
? Allow molten material to solidify before disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
41
16 PUBLICATION SUMMARY REPORT
Polymer in Nalco 98 AUS047
Summary Report
Reference No: PLC/448
Nalco Australia Pty Ltd (ABN 41 000 424 788) of 2 Anderson Street Banksmeadow NSW
2019 has submitted a synthetic polymer of low concern (PLC) notification statement in
support of their application for an assessment certificate for Polymer in NALCO 98 AUS047.
The notified polymer is intended to be used to achieve solid/liquid separation in waste
circuits in mineral sands processing plants. Approximately 150 tonnes of the notified polymer
will be manufactured per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern, and all pondage will be contained within the mine site with no release to any natural
waterways.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
42
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The wastes containing the notified polymer should be disposed of in an approved
incinerator or waste treatment/disposal site in accordance with all applicable
regulations.
? The wastes should not be disposed of in sewer or with normal garbage.
? Empty containers should be triple rinsed (or equivalent), with the rinsate added to the
slimes being treated, and the containers offered for recycling or reconditioning, or
they should be punctured and disposed of in a sanitary landfill or by other procedures
approved by state and local authorities.
Emergency procedures
? The product should be prevented from entering natural waterways or sewers.
? Soak up small spills with absorbent material and place in suitable, covered and
properly labelled containers. Wash affected area.
? Soak up as thoroughly as possible with inert absorbent material or sawdust. Do not
wash the affected area until all possible traces are removed as water in contact with
the product will create a voluminous and slippery gel.
? Disposed the contaminated recovered material via an approved waste hauler and in
accordance with the disposal considerations.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria; and
- a more significant release to water such as the sewer or natural water bodies is
likely to occur. Provision of freshwater aquatic toxicity data of the notified
polymer rather than those currently available for a surrogate for marine species
will be required.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
43
17 PUBLICATION SUMMARY REPORT
Aristoflex AVC
Summary Report
Reference No: PLC/473
Clariant (Australia) Pty Ltd (ABN 30 069 435 552) of Warrigal Road, Chadstone VIC 3148;
and Unilever Australasia Pty Ltd (ABN 66 004 050 828) of 219 North Rocks Road, North
Rocks NSW 2151, have submitted a joint synthetic polymer of low concern (PLC)
notification statement in support of their application for an assessment certificate for
Aristoflex AVC. The notified polymer will be used a gelling agent for aqueous systems and
as a texturiser, thickener for oil-in-water emulsions. Less than one tonne of the notified
chemical will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard. The powder may cause irritation to the eyes and repeated or prolonged skin contact
may result in mild irritation. A small fraction of the polymer particles are in the inspirable
range and mechanical irritation to the respiratory tract may occur if inhaled.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is low concern to public health when used in the intended manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern and PEC/PNEC ratio.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
44
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of by incineration or landfill in accordance
with State/Territory waste management regulations. Product containing the notified
polymer should be disposed of to sewer.
Emergency procedures
? Spills/release of the notified polymer should be handled by sweeping and placing
spilled powder in sealed container for disposal. Do not allow entry to stormwater
drains or waterways.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
45
18 PUBLICATION SUMMARY REPORT
Polymer in Polyurethane Dispersion 145049
Summary Report
Reference No: PLC/474
Dow Chemical (Australia) Ltd of 541-583 Kororoit Creek Road Altona Vic 3018 has
submitted a synthetic polymer of low concern (PLC) audited self assessment report in support
of their application for an assessment certificate for Polymer in Polyurethane Dispersion
145049. The notified polymer is intended to be used industrially as component of formulated
surface coatings and adhesives. One to 40 tonnes of the notified chemical will be imported
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Environmental Assessment
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
Occupational Health & Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used to produce the components /materials
described.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? The following personal protective equipment is recommended in accordance with
good occupational health and safety practice:
- Chemical goggles, clean, body-covering clothing, and chemical gloves resistant
to this material
- In misty atmospheres, use an approved particulate respirator
? No specific engineering controls, work practices or additional personal protective
equipment are required for the safe use of the notified polymer itself, however, these
should be selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
46
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
Disposal
? It is recommended that any waste amounts of dispersion product containing the
polymer substance are sent to a licensed, permitted, ; recycler, reclaimer, incinerator,
or other thermal destruction device.
Storage
?The following precautions should be taken by distributors and product end-users
regarding storage of the notified polymer / dispersion product:
- Store between 40-110F (4-43C). Avoid Freezing.
Emergency procedures
? Spills/release of the notified polymer / dispersion should be handled by Isolate area.
? Keep unnecessary and unprotected personnel from entering area. Spilled material
may cause a slipping hazard. Use appropriate safety equipment.
? Prevent from entering into soil, ditches, sewers, waterways and/or groundwater.
? Contain spilled material if possible. Absorb with material such as clay or sand. Wash
the spill site with large quantities of water.
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Secondary Notification
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
47
19 PUBLICATION SUMMARY REPORT
Polymer in Optiflo M2600/M2600VF
Summary Report
Reference No: PLC/490
Amtrade International Pty Ltd (ABN 49 006 409 936) of Level 6, 574 St Kilda Road
Melbourne, VIC 3004 has submitted a synthetic polymer of low concern (PLC) notification
statement in support of their application for an assessment certificate for Polymer in Optiflo
M2600 / M2600VF. The notified polymer is intended to be used as a paint thickener. It will
be incorporated into water-based paint formulations for sale to the trade and the public. Less
than 50 tonnes of the notified polymer will be imported per annum for each of the first five
years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
As no toxicological data were available for the notified polymer the polymer cannot be
assessed against the NOHSC Approved Criteria for Classifying Hazardous Substances. Due
to the high molecular weight and low reactivity of the polymer, the toxicological hazard of
the polymer is expected to be low. The residual monomer concentrations in the polymer are
below the cutoff levels for classification of the polymer as a hazardous substance.
Occupational Health and Safety
The notified polymer is of Low Concern to occupational health and safety under the
conditions of the occupational settings described.
Public Health
There is Low Concern to public health when the finished paint products containing the
notified polymer are used in the proper manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Use the imported products and finished paints containing the notified polymer with
adequate ventilation. The MSDS recommends that local exhaust ventilation be used
when opening the imported product containers or when the products are transferred.
? Protective eyewear, chemical resistant industrial clothing and footwear and
impermeable gloves (composed of butyl rubber, nitrile rubber or neoprene) should be
worn during occupational use of the imported products containing the notified
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
48
polymer in concentrated form. Where engineering controls and work practices do not
reduce vapour and particulate exposure to safe levels, an air fed respirator should also
be used.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
? Spillage of the imported products and finished paints containing the notified polymer
should be avoided. Spillages should be cleaned up promptly.
Disposal
? The notified polymer should be disposed of in accordance with State/Territory and
Commonwealth legislative requirements and applicable waste management
guidelines.
? Waste generated during industrial application if of surface coatings containing the
notified polymer should be disposed of through a licensed waste transporter to a
licensed waste facility, such as a landfill or incinerator, in accordance with
State/Territory and Commonwealth legislative requirements and applicable waste
management guidelines.
Emergency procedures
? Large spills of the imported products should be contained by dyking, and pumped into
resealable, labelled containers for recycling or disposal in accordance with
State/Territory legislative requirements and applicable waste management guidelines.
Soak up remainder with absorbent material. Small spills should be contained (e.g. by
dyking) and absorbed with inert materials (e.g. sand, earth). Collect absorbed material
into resealable, labelled containers for disposal in accordance with State/Territory
legislative requirements and applicable waste management guidelines. Use caution to
avoid slipping. Flush affected area with copious amounts of water but only if waters
are collected for appropriate disposal in accordance with State/Territory legislative
requirements. Keep spills and cleaning runoff out of municipal sewers, stormwater or
open bodies of water.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
49
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
50
20 PUBLICATION SUMMARY REPORT
Topas
Summary Report
Reference No: PLC/493
Amtrade International Pty Ltd (ABN 49 006 409 936) of Level 2, 570 St Kilda Road,
Melbourne VIC 3004 has submitted a synthetic polymer of low concern (PLC) notification
statement in support of their application for an assessment certificate for Topas. The notified
polymer is intended to be used for production of moulded articles and films, including food
contact materials. Up to 400 tonnes of the notified polymer will be imported per annum for
each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Topas has low potential for presenting health hazards resulting from its solid, pelletised form,
lack of functional groups of concern and low solubility. Acute toxicity studies confirm the
product is of low acute toxicity. The notified polymer meets the PLC criteria and can
therefore be considered to be of low hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used for production of finished articles
and films including food-contact materials.
Environmental Effects
Topas is not considered to be a risk to the environment based on its form and use pattern.
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself unless operator is likely to
come in contact with molten material or pellets may enter eye. Eye protection should
be worn if there is a risk of material entering eye. If handling or likely to contact
molten material, operators should wear long trousers, shirt with long sleeves and
insulated gloves.
? A copy of the MSDS should be easily accessible to employees.
Disposal
? The notified polymer should be disposed of in routine commercial waste.
Storage
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
51
? The following precautions should be taken by warehousing/storage facilities
regarding storage of the notified polymer:
- Avoid storage with strong oxidising agents.
Emergency procedures
? Spills/release of the notified polymer should be handled by sweeping and recovery.
Material which has not been contaminated can be used. Contaminated material
should be disposed of in commercial waste
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
52
21 PUBLICATION SUMMARY REPORT
Polymer in S-9974
Summary Report
Reference No: PLC/495
Cytec Australia Holdings Pty Ltd (ABN 45 081 148 629) of Suite 1, Level 1, Norwest Quay,
21 Solent Circuit, Norwest Business Park, Baulkham Hills NSW 2153 has submitted a
synthetic polymer of low concern (PLC) notification statement in support of their application
for an assessment certificate for Polymer in S-9974 The notified polymer is intended to be
used as an anti-scalant agent. Less than 800 tonnes of the notified polymer will be imported
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is No Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used as an anti-scalant agent.
Environmental Effects
The notified polymer is not considered to pose a risk to the environment based on its reported
use pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? Engineering control procedures such as local exhaust ventilation should be used.
? Personnel should wear a two-piece PVC suit with hood or PVC overalls with hood
and ensure adequate ventilation is present during the metal refinery when transferring
the S-9974 containing the notified polymer and during routine maintenance and
repairs.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
53
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? The notified polymer should be disposed of to landfill or incinerated according to
State and local government regulations.
Emergency procedures
? Spills of the notified polymer should be handled by covering spills with some inert
absorbent and sweeping material up into containers for disposal to landfill. Flush spill
area with water.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
54
22 ACCESS TO FULL PUBLIC REPORT
NICNAS publishes a Full Public Report for each new chemical assessed. These reports are
available for public inspection at the library of the National Occupational Health & Safety
Commission at their Canberra office by appointment only. Please call the library on (02)
6279 1161 or (02) 6279 1163 to arrange to view the Full Public Report.
Reports can also be viewed and downloaded free of charge from our website at
www.nicnas.gov.au. Copies of these reports may also be requested, free of charge, by
contacting the Administration Section of NICNAS by phone: (02) 8577 8816 or fax: (02)
8577 8888.
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
55
23 LOW VOLUME CATEGORY PERMITS
The permits listed in Table 2 were issued to import or manufacture the following chemicals
under section 21U of the Industrial Chemicals (Notification and Assessment) Act 1989. Low
Volume Category Permits are approved for 36 months.
Table 1
Low Volume Category Permits
PERMIT COMPANY COMPANY CHEMICAL OR TRADE HAZARDOUS USE DATE
NUMBER NAME POSTCODE NAME SUBSTANCE
658 Firmenich 2093 Walnut Ester Yes Cosmetic 20.8.04
Limited
659 Trimex Pty Ltd 2018 Polyquaternium 59 Yes Cosmetic 20.8.04
660 ISP 2141 2,5-Furadione ND Cosmetic 20.8.04
(Australasia) polymer with 2-
Pty Ltd methyl-1-propene,
ethyl ester reaction
product with N,N-
dimethyl 1,3-
propandediamine &
polyethylene glycol
2-aminopropyl Me
ether
661 Caltex Australia 2000
Petroleum Pty
Ltd Chemical in Starplex ND Component 27.8.04
HD2 of a grease
product
662 Australasian 4178
Lubrication
Manufacturing
Company
663 Dow Chemical 3018
(Aust) Ltd
XTJ-505 Additive Yes Lubricant 10.9.04
additive
664 Castrol Aust 2161
Pty Ltd
N.D.: not determined; insufficient data available to effect a health effects classification under
Approved Criteria [NOHSC:1008(1999)]
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
56
24 COMMERCIAL EVALUATION CATEGORY PERMIT
The permits listed in Table 1 were issued to import or manufacture the following chemicals
for commercial evaluation under section 21G of the Industrial Chemicals (Notification and
Assessment) Act 1989.
Table 2
Commercial Evaluation Category Permits
PERMIT COMPANY COMPANY CHEMICAL HAZARDOUS QUANTITY USE PERIOD
NUMBER NAME POSTCODE OR TRADE SUBSTANCE APPROVED
NAME
6 months
Ashland 2162 Yes 4000 kg Resin
593 Isocure I AL
Pacific Pty binder for
XX486
Ltd metal sand
casting
6 months
GE Betz Pty 2565 Yes 4000 kg Metal
594 Hexafluorotit
Ltd surface
anic acid
treatment &
acid mist
suppressant
2 yrs
3175 Yes 4000 kg Curable
DIC Component
595
resin in
International in Daicure
surface
(Australia) 6200
coatings
Pty Ltd
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
57
25 EARLY INTRODUCTION PERMITS FOR NON-HAZARDOUS INDUSTRIAL
CHEMICALS
The permits listed in Table 3 were issued to import or manufacture the following chemicals
prior to the issue of their respective assessment certificates under section 30A of the Act.
Table 3
Early Introduction Permits
PERMIT COMPANY CHEMICAL OR USE
NUMBER NAME TRADE NAME
341 Kodak Component of Budex Photography
Australasia 5103
Pty Ltd
342 PPG Polymer in PPG2790- Packaging
Industries 301A/190K
Australia Pty
Ltd
343 Akzo Nobel
Pty Ltd
344 BASF Akzo Polymer in EMA 1015 Surface coating
Nobel Resin
Automotive
OEM
345 Akzo Nobel
Pty Ltd
346 BASF Akzo Polymer in ACW-1011 Surface coating
Nobel Resin
Automotive
OEM
347 Akzo Nobel
Pty Ltd
348 BASF Akzo Polymer in Adekanol Surface coating
Nobel UH-814N
Automotive
OEM
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
58
26 NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE AUSTRALIAN
INVENTORY OF CHEMICAL SUBSTANCES FIVE YEARS AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 14(1) of the Industrial Chemicals (Notification
and Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 4
Chemicals Eligible for Listing on the Australian Inventory of Chemical Substances
CHEMICAL NAME CAS MOLECULAR
NUMBER FORMULA
25213-88-1 (C8H8.C5H8O2.C3H3N)x
2-Propenoic acid, 2-methyl-, methyl ester,
polymer with ethenylbenzene and 2-
propenenitrile
Unspecified
188070-47-5
Glycine, N-[3-(acetylamino)phenyl]-N-
(carboxymethyl)-, mixed Et and Me diesters,
reaction products with diazotized 2-chloro-4-
nitrobenzenamine
Benzene, 1,1'-oxybis-, sec-hexyl derivs., 147732-60-3 Unspecified
sulfonated, sodium salts
198495-69-1 Unspecified
Castor oil, hydrogenated, polymer with p-
tert-butylbenzoic acid, fumaric acid, phthalic
anhydride and trimethylolpropane
206987-67-9 (C8H14O2.C8H8.C7H12O
2-Propenoic acid, 2-methyl-, polymer with
butyl 2-methyl-2-propenoate, butyl 2- 2.C7H10O3.C5H8O3.C5H
propenoate, ethenylbenzene, 2-hydroxyethyl 8O2.C4H6O2.C4H6O2)x
2-propenoate, methyl 2-methyl-2-propenoate,
methyl 2-propenoate and oxiranylmethyl 2-
methyl-2-propenoate
154979-42-7 (C15H16O2.(C3H6O)n
Propanoic acid, 2-hydroxy-,compound with
alpha-(2-aminomethylethyl)-omega-(2- C6H16N2O.C3H5ClO)x.
xC3H6O3
aminomethylethoxy)poly[oxy(methyl-1,2-
ethanediyl)] polymer with
(chloromethyl)oxirane and 4,4'-(1-
methylethylidene)bis[phenol]
Fatty acids, C18-unsatd., dimers, polymers 366491-45-4 Unspecified
with polyethylene glycol and sebacic acid
Dodecanoic acid, polymer with aziridine, 2- 202263-77-2 (C12H24O2.C6H10O2.C5
oxepanone and tetrahydro-2H-pyran-2-one H8O2.C2H5N)x
120029-06-3 C39H50N12O7S2.2Na
2-Naphthalenesulfonic acid, 7-[[4,6-bis[[3-
(diethylamino)propyl]amino]-1,3,5-triazin-2-
yl]amino]-4-hydroxy-3-[[4-[(4-
sulfophenyl)azo]phenyl]azo]-, disodium salt
(C8H6O4.C8H4O3.C6H
1,3-Benzenedicarboxylic acid, polymer with 71010-58-7
10O4.C5H12O4.C5H12O
2,2-bis(hydroxymethyl)-1,3-propanediol,
2)x.xC7H6O2
2,2-dimethyl-1,3-propanediol, hexanedioic
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
59
acid and 1,3-isobenzofurandione, benzoate
C9H15N3O2
2-Propenamide, 2-methyl-N-[2-(2-oxo-1- 3089-19-8
imidazolidinyl)ethyl]-
C5H6N2O
3-Pyridinol, 2-amino- 16867-03-1
Unspecified
72749-55-4
Imidazolium compounds, 2-(C17 and C17-
unsatd. alkyl)-1-[2-(C18 and C18-unsatd.
amido)ethyl]-4,5-dihydro-1-methyl, Me
sulfates
Unspecified
224790-80-1
Phenol, 2-methyl-, reaction products with 5-
ethylidenebicyclo[2.2.1]hept-2-ene,
hydrogenated
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
60
27 NOTICE OF AMENDMENTS TO THE AUSTRALIAN INVENTORY OF
CHEMICAL SUBSTANCES
Notice is given in accordance with section 20 of the Industrial Chemicals (Notification and
Assessment) Act 1989 (the Act) that the following amendment have been made to the
Australian Inventory of Chemical Substances (AICS).
Table 5
Amendment to AICS
Addition of CAS number, CAS approved chemical name, molecular formula to AICS.
CHEMICAL NAME CAS MOLECULAR
NUMBER FORMULA
18760-44-6 C14H28O3S
Thiophene, 3-
(decyloxy)tetrahydro-, 1,1-
dioxide
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
61
28 NOTICE OF CHEMICALS ELIGIBLE FOR IMMEDIATE LISTING ON THE
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 13B of the Industrial Chemicals (Notification and
Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 6
Chemicals Eligible for Immediate Listing on the Australian Inventory of Chemical
Substances
CHEMICAL NAME CAS MOLECULAR
NUMBER FORMULA
Bicyclo[2.2.1]hept-2-ene, polymer with 26007-43-2 (C7H10.C2H4)x
ethene
Unspecified
495403-02-6
Siloxanes and Silicones, 3-[(2-
aminoethyl)amino]-2-methylpropyl Me, di-
Me, reaction products with N,N,N-
trimethyloxiranemethanaminium chloride
Chemical Gazette Commonwealth of Australia Gazette
No. C 10, 5 October 2004
|