Microsoft Word - GazMay 07.doc
Gazette
Australian Government
No. C 05, Tuesday 1 May 2007
CHEMICAL
Published by the National Industrial Chemicals
Notification and Assessment Scheme - NICNAS
?Commonwealth of Australia 2007
ISBN 1035-9877
This work is copyright. Apart from any use as permitted under the Copyright Act 1968, no part may be reproduced by any
process without prior written permission from the Commonwealth available from the Attorney-General's Department.
Requests and inquiries concerning reproduction and rights should be addressed to:
Commonwealth Copyright Administration
Copyright Law Branch
Attorney-General's Department
Robert Garran Offices
National Circuit
Canberra ACT 2600
email: Commonwealth.Copyright@ag.gov.au
web:
The Industrial Chemicals (Notification and Assessment) Act 1989 (the Act) commenced on
17 July 1990. As required by Section 5 of the Act, a Chemical Gazette is published on the
first Tuesday in any month or on any days prescribed by the regulations.
CONTENTS
SPECIAL NOTICES
1 HAZARDOUS SUBSTANCES INFORMATION SYSTEM (HSIS) 5
UPGRADE
2 PHTHALATE HAZARD ASSESSMENTS AND HAZARD 6
COMPENDIUM ?CALL FOR COMMENTS
3 NEW DATA ON CASTOR OIL, MONOMALEATE 9
4 NDPSC CONSIDERS ISSUE OF DERIVATIVE FOR SCHEDULING 11
5 LEAD COMPOUNDS IN COSMETICS ?CALL FOR INFORMATION 12
NEW CHEMICALS
SUMMARY REPORTS
6 LTD/1128 CHEMICAL 1 IN PETRO PRODUCTS 17
7 LTD/1273 STOCK 3336 19
8 LTD/1313 HEXAFLUOROTITANIC ACID 21
9 STD/1088 CHEMICAL 2 IN PETRO PRODUCTS 25
10 PLC/654 IRGASTA P16 AND POLYMER IN IRGASTA 28
P18
11 PLC/666 AQUALOC HS-1 30
12 PLC/669 SEKISUI TECHPOLYMER MBX SERIES 32
13 PLC/686 POLYMER IN LOTADER 4503 AND LOTADER 35
3430
14 PLC/692 POLYMER IN AD0979P 37
15 PLC/694 DEGALAN LP 65/12 39
16 PLC/695 AQUALOC HW-1B 41
17 SAPLC/56 PERMAPOL 97-125 43
18 SAPLC/58 PERMAPOL P3.1E 45
19 SAPLC/63 POLYMER IN DAICURE DG-4K 47
20 ACCESS TO FULL PUBLIC REPORT 49
PERMITS ISSUED
21 LOW VOLUME CHEMICAL PERMITS 50
22 COMMERCIAL EVALUATION CATEGORY PERMITS 51
23 EARLY INTRODUCTION PERMITS 52
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES
53
24 NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES FIVE
YEARS AFTER ISSUING OF ASSESSMENT CERTIFICATES
55
25 NOTICE OF CHEMICALS ELIGIBLE FOR IMMEDIATE LISTING
ON THE AUSTRALIAN INVENTORY OF CHEMICAL
SUBSTANCES AFTER ISSUING OF ASSESSMENT
CERTIFICATES
5
1 HAZARDOUS SUBSTANCES INFORMATION SYSTEM (HSIS) UPGRADE
The Hazardous Substances Information System (HSIS) was first released by the National
Occupational Health and Safety Commission in January 2005. It has now has been upgraded
to fit the look and feel of the Australian Safety and Compensation Council (ASCC) website
and to be compliant with IT requirements within the Department of Workplace Relations
(DEWR).
Although the basic structure and operation of the HSIS will be very similar to the first
version, a number of new features and improvements have been introduced. New features
include:
? Simplified search screens that can be expanded to an "Advanced Search" screen
when required
? Ability to enter CAS numbers with or without dashes
? Improved searching where chemical names have a prefix (for example "3-" or
"tert-"). The previous system was unable to search directly for a prefix.
? Ability to search for records that were amended within a specified date range
? A guide to abbreviations and notes used within a particular column of results can
be accessed by clicking on the column heading
? Access to pdf documents that contain all of the hazardous substance records in the
database. The consolidated lists will be updated each time there is a change to the
records in the searchable database.
? Ability to specify the number of search results displayed on the screen
? Ability to print search results in pdf format
The new version is supported by a revised User Instruction Manual and updated guidance
material. A dedicated email box for providing feedback on HSIS is available at
feedback.HSIS@dewr.gov.au
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
6
2 PHTHALATE HAZARD ASSESSMENTS AND HAZARD COMPENDIUM ?br>
CALL FOR COMMENTS
Phthalates are the most common group of chemicals used as plasticisers (plastic softeners)
worldwide. They are employed in a diverse range of industrial and domestic applications and
can be present in soft plastics at concentrations up to 35-45%.
In response to concerns over potential adverse human health effects from exposure to
phthalates, NICNAS conducted general data searches and a call for information on phthalates
from Industry in 2004 and has identified 25 individual phthalate chemicals (Table 1) potentially
in use in Australia.
Hazard Assessments and Hazard Compendium
Draft human health hazard (toxicity) assessments for these phthalates have been conducted and
NICNAS is now seeking comment on these hazard assessments. For all assessments, NICNAS
has utilised information, where available, from peer reviewed overseas assessment reports
updated with recent literature surveys.
Table 1. Twenty-five Phthalate Chemicals Subject to Human Health Hazard Assessments
Common Abbreviation Common Name CAS #
DEHP* Diethylhexyl phthalate 117-81-7
DIDP* Diisodecyl phthalate 26761-40-0,
68515-49-1
DMP* Dimethyl phthalate 131-11-3
DINP* Diisononyl phthalate 28553-12-0,
68515-48-0
DBP* Dibutyl phthalate 84-74-2
BBP* Butylbenzyl phthalate 85-68-7
DnOP* Di-n-octyl phthalate 117-84-0
DEP* Diethyl phthalate 84-66-2
DMEP* Bis(2-methoxyethyl) phthalate 117-82-8
DAP Diallyl phthalate 131-17-9
DCHP Dicyclohexyl phthalate 84-61-7
DIBP Diisobutyl phthalate 84-69-5
Di-C6-10-phthalate Di-C6-10-phthalate 68515-51-5
Di-C7-9-phthalate Di-C7-9-phthalate 68515-41-3
Di-C9-11-phthalate Di-C9-11-phthalate 68515-43-5
DIHepP Diisoheptyl phthalate 71888-89-6
DIHP Diisohexyl phthalate 68515-50-4,
71850-09-4
DIOP Diisooctyl phthalate 27554-26-3
DTDP Ditridecyl phthalate 119-06-2
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
7
DIUP Diisoundecyl phthlate 85507-79-5
DMT Dimethyl terephthalate 120-61-6
DnHP Di-n-hexyl phthalate 84-75-3
DNP Dinonyl phthalate 84-76-4
DITDP Diisotridecyl phthalate 68515-47-9
DUP Diundecyl phthalate 3648-20-2
* additionally declared as Priority Existing Chemicals for public health risk assessments
In addition to these 25 individual phthalate hazard assessments for which comments are sought,
the hazard profiles for all 25 phthalates have been compiled into a draft Phthalate Hazard
Compendium providing a comparative analysis of key toxicity endpoints for these phthalates.
Comment is also sought on this Phthalate Hazard Compendium.
All 25 draft hazard assessments and the Phthalate Hazard Compendium are now available as
separate documents downloadable from the NICNAS website at http://www.nicnas.gov.au/. In
addition, on request, these documents are available free of charge in pdf format on a CD-ROM
directly from NICNAS.
In accordance with discussions with industry and community stakeholders in December 2006,
NICNAS is scheduling a 3-month comment period. Comments on any or all of these draft
documents must be provided by 1 August 2007 and should be sent to:
Vivian Chan
Rapid Risk Assessment
NICNAS
GPO Box 58
Sydney NSW 2001
Fax (02) 8577 8888
Email vivian.chan@nicnas.gov.au
Requests for CDROMs containing these draft reports should be sent to:
Ms Virginia Parish
Review and Treaties
NICNAS
GPO Box 58
Sydney NSW 2001
Fax (02) 8577 8888
Email virginia.parish@nicnas.gov.au
Risk Assessments
Consumer products such as soft plastic articles and cosmetics are potentially sources of
repeated and long-term exposure to phthalates through migration and leaching. Within this
group of 25 phthalate chemicals, 9 phthalate chemicals (highlighted in Table 1) were
additionally declared as Priority Existing Chemicals (PECs) on 7 March 2006 for full public
health risk assessments for the following specific consumer applications:
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
8
Children's toys;
Childcare articles; and
Cosmetics
Following the consideration of comments, the hazard assessments for these 9 phthalates will be
used to conduct public health risk assessments for these phthalates in these applications.
If you have any questions regarding the hazard assessments or the assessment processes, please
contact Dr Graham Harvey, tel: (02) 8577 8851 fax: (02) 8577 8888 or email:
graham.harvey@nicnas.gov.au.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
9
3 NEW DATA ON CASTOR OIL, MONOMALEATE
Castor oil, monomaleate was assessed by NICNAS as LTD/1255 and a public report
published in July 2006. ISP (Australasia) Pty Ltd recently submitted an additional study
report "A local lymph node assay" for the notified chemical, castor oil, monomaleate. This
study was not available at the time of assessment of castor oil, monomaleate as a new
chemical.
A summary of the new study is provided below. The summary will be appended to the
LTD/1255 public report.
Study summary
The study was performed according to the OECD Test Guideline 429: Skin Sensitisation:
Local Lymph node Assay. The study was conducted in groups of 5 female mice that received
0, 2.5, 5 or 10 % triclosan in acetone/olive oil (4/1, v/v) and also included a positive control.
There were no deaths during the study. No signs of systemic toxicity were observed in the
test or control animals during the study. The body weight changes of the test animals between
Day 0 and Day 5 were comparable to those observed in the corresponding control group
animals over the same period. Slight erythema was seen in all animals receiving 10 %
triclosan from day 1 to 5. The observed proliferation response and corresponding stimulation
index are shown below.
Concentration Proliferative response Stimulation Index
(% w/w) (DPM/lymph node) (Test/Control Ratio)
Test Substance
0 (vehicle control) 403
2.5 574 1.4
5 765 1.9
10 1173 2.9
Positive Control
5 Not given 2.4
10 Not given 2.5
25 Not given 9.0
The DPM/lymph node counts and stimulation index values presented above are the mean for
each test concentration, though individual DPM/lymph node counts were also determined for
each animal. This allowed statistical analysis of the data. This analysis indicated that,
compared to controls, a statistically significant increase was seen at 10 %. Furthermore
examination of the individual DPM/lymph node counts in animals receiving 10 % test
material indicated an outlier: stimulation index of 0.7 compared to 2.5, 2.8, 3.8 and 4.7.
Elimination of this outlier resulted in a mean stimulation index of 3.5. Thus, there was
evidence of induction of a lymphocyte proliferative response indicative of skin sensitisation
to castor oil, monomaleate.
As the local lymph node assay does not change the present hazard classification of castor oil,
monomaleate with R43 ("May cause sensitisation by skin contact"), this additional study
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
10
does not trigger a secondary notification, according to Section 64(2)(e) of the Industrial
Chemicals (Notification and Assessment) Act 1989.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
11
4 NDPSC CONSIDERS ISSUE OF DERIVATIVE FOR SCHEDULING
At the recent National Drugs and Poisons Schedule Committee (NDPSC) Meeting 49, held
on 20-22 February 2007, there was consideration of the usage of the term "derivative" in the
Standard for the Uniform Scheduling of Drugs and Poisons (SUSDP).
As detailed in the NDPSC Record of Reasons (available on the NDPSC website at this url:
http://www.tga.gov.au/ndpsc/records.htm) the NDPSC agreed to amend the "Principles of
Scheduling" section of the SUSDP to clarify the intent of the Committee in using derivative
in the context of a schedule entry as follows:
PRINCIPLES OF SCHEDULING - READING THE SCHEDULES ?Amendment (new
paragraph to be added)
? It is important to note that a substance is not classed as a derivative on the basis of a
single, prescriptive set of criteria. Classification of a substance as a derivative of a
Scheduled poison relies on a balanced consideration of factors to decide if a substance has
a similar nature (e.g. structurally, pharmacologically, toxicologically) to a Scheduled
poison or is readily converted (either physically or chemically) to a Scheduled poison.
However, a substance is only considered a derivative of a Scheduled poison if it is not
individually listed elsewhere in the Schedules, or captured by a more restrictive group or
class entry. Additionally, some entries specifically exclude derivatives. Once a
substance is determined to be a derivative of a Scheduled poison, the same scheduling
requirements as the Scheduled poison, including limits on access, supply and availability,
will apply.
In accordance with subsection 52D (4) of the Therapeutic Goods Act 1989, a notice advising
of the amendment to the SUSDP was published in the Commonwealth of Australia Gazette
on 11 April 2007.
The amendments arising from this notice will be incorporated into SUSDP 22 Amendment 1
effective 1 September 2007, which should be available for purchase from National Mailing
and Marketing Pty Ltd in August 2007, telephone (02) 6269 1035 (or using the subscription
order form available at the following webpage http://www.tga.gov.au/ndpsc/susdp.htm).
Stakeholders are reminded that the NDPSC regularly considers issues regarding the
scheduling of chemicals, and that pre- and post-meeting notices, as well as the Record of
Reasons for NDPSC meetings, are available from the NDPSC website
(http://www.tga.gov.au/ndpsc). Should stakeholders wish to remain up to date on scheduling
matters it is highly advised that these documents be monitored.
Any queries or questions can be addressed to the NDPSC Secretariat (e-mail
NDPSC@health.gov.au, phone 02 6160 3200 or Facsimile 02 6160 3299).
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
12
5 LEAD COMPOUNDS IN COSMETICS - CALL FOR INFORMATION
The Director of the National Industrial Chemicals Notification and Assessment
Scheme (NICNAS) is seeking information, under section 48 of the Industrial
Chemicals (Notification and Assessment) Act 1989 (the Act), on cosmetic products
containing lead compounds and any lead compounds used in the manufacture of
cosmetics.
Lead compounds used in cosmetics are of interest because they are hazardous to
human health and the environment. Information is sought on all cosmetic products
that contain lead to determine if any further regulatory action is required for cosmetics
containing lead.
The notice is directed to all persons who have manufactured or imported lead
compounds for use in cosmetics or imported cosmetic products containing lead
compounds in the calendar years 2005 and 2006. Any other persons with information
on these chemicals including users, past importers or manufacturers are also
encouraged to provide information on the chemicals.
The following information is required on lead compounds manufactured in or
imported into Australia and used to formulate cosmetic products:
Chemical name and CAS number of the lead compound;
?br>
Quantities imported and/or manufactured in Australia in the calendar years
?br>
2005 and 2006 for use in cosmetics;
Specific function of the lead compound in the cosmetic product, and
?br>
Name of the cosmetic product/mixture the compound is used in.
?br>
Information required on imported cosmetic products/mixtures containing lead
compounds include:
Product/mixture name;
?br>
Chemical name and CAS number of the lead compound present in the product;
?br>
Concentration of the chemical in the product/mixture;
?br>
Specific use(s) of the product/mixture containing the chemical, and
?br>
Quantities of the product/mixture imported and/or manufactured in Australia
?br>
in the calendar years 2005 and 2006.
In accordance with section 50 of the Act, the information may be accompanied by an
application that some or all of the information provided be treated as exempt
information. The form for Application for Exempt Information is available on the
NICNAS website at www.nicnas.gov.au/Forms/Existing_Chemicals/Form3_PDF.pdf
A cosmetic product is defined as `A substance or preparation intended for placement
in contact with any external part of the human body, including the mucous
membranes of the oral cavity and the teeth; with a view to: altering the odours of the
body; or changing its appearance; or cleansing it; or maintaining it in good condition;
or perfuming it; or protecting it.' Examples of cosmetic products include, personal
hygiene products, hair and skin care products, face and nail care products and face
paints.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
13
This is not an exhaustive list of potential cosmetic products, but is indicative of the
types of products which are of interest in this call for information.
Currently one lead compound has an assigned INCI name (Lead acetate).
For further information on cosmetic products contact Sami Syed on (02) 8577 8845 or
by e-mail at sami.syed@nicnas.gov.au
Response forms to assist industry in providing the relevant information are attached.
Please complete the appropriate forms by 1 June 2007 and forward to:
Sami Syed
Review and Treaties
NICNAS
G P O Box 58
Sydney, NSW 2001
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
14
Contact Details
Company name:
Company address:
Contact person:
Telephone number:
Email address:
Signature:
Date:
Information collected by NICNAS may be provided to State, Territory or Commonwealth regulatory
agencies for the purposes of monitoring compliance under relevant legislation. All information
collected is treated in accordance with strict confidentiality guidelines and in compliance with the
Privacy Act 1988.
Is your company a small business with less than 20 employees? YES NO
If yes, please provide an estimate of the time taken to complete this form:
hrs mins
Thank-you. Please send the completed form to: Sami Syed
Review & Treaties
NICNAS
GPO Box 58
Sydney NSW 2001
.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
15
Attachment: Survey forms
Table 1: Importation / manufacture of lead compounds for use in cosmetics:
Do you manufacture lead compounds for use in cosmetics? YES/NO
?br>
Do you import lead compounds for use in cosmetics? YES/NO
?br>
Please fill in the table below for each chemical you import or manufacture.
?br>
Name of Product Import / Manufact.
Lead Compound
Concentration of Lead
Containing the Lead Volume of
Name / CAS No. Compound in the Known Uses of the Substance
Compound Product (kg)
Product
2005 2006
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
16
Table 2: Importation / manufacture of products/mixtures containing lead compounds for use in cosmetics
? Do you manufacture products/mixtures containing lead compounds for cosmetic use? YES/NO
? Do you import products/mixtures containing lead compounds for cosmetic use? YES/NO
? Please fill in the table below for each product/mixture you import or manufacture.
Import/Manufact.
Lead Compound
Conc. of Lead
Volume Range of
in the
Product/mixture Known Uses of the
Compound in
Product/mixture (kg)
Product/mixture
Name Product/mixture
Product/mixture
Name / CAS No.
2005 2006
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
17
6 PUBLICATION SUMMARY REPORT
Chemical 1 in Petro Products
Summary Report
Reference No: LTD/1128
Akzo Nobel Chemicals Pty Ltd of Suite 10, 89 High St Kew VIC 3101 has submitted a
limited notification statement in support of their application for an assessment certificate for
Chemical 1 in Petro Products. The notified chemical is intended to be used in hard surface
(e.g. floors), metal, carpet and brewery cleaners and as a rinse aid (e.g. dishwashing
machines). The notified chemical will be reformulated into a number of products which are
then used as is or diluted for use. Less than one tonne of the notified chemical will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data, the notified chemical is cannot be classified as a hazardous
substance in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used as described.
Environmental Effects
On the basis of the PEC/PNEC ratio:
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
18
Disposal
? The notified chemical should be disposed of by incineration or to landfill.
Emergency procedures
? Spills/release of the notified chemical should be physically contained, collected and
disposed of in an appropriate manner.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
19
7 PUBLICATION SUMMARY REPORT
Stock 3336
Summary Report
Reference No: LTD/1273
Mobil Oil Australia Pty Ltd (ABN 88 004 052 984) of 12 Riverside Quay, Southbank VIC
3006 has submitted a limited notification statement in support of their application for an
assessment certificate for Stock 3336. The notified polymer is intended to be used as an
additive for industrial gear oils (<0.3% (w/w)). Up to 1 tonne of the notified polymer will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified polymer cannot classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used in the proposed manner.
Environmental Effects
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Regulatory Controls
Control Measures
Occupational Health and Safety
? Where prolonged contact with the skin is unavoidable, wearing of personal protective
equipment is recommended in accordance with good industrial hygiene practices.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
20
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of by incineration or to secure landfill.
Emergency procedures
Spills or accidental release of the notified polymer should be handled by physical
containment, collection and subsequent safe disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified polymer; or
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
21
8 PUBLICATION SUMMARY REPORT
Hexafluorotitanic Acid
Summary Report
Reference No: LTD/1313
Chemetall (Australasia) Pty Ltd (ABN 25 074 869 015) of 17 Turbo Drive, Bayswater North
VIC 3153 has submitted a limited notification statement in support of their application for an
assessment certificate for Hexafluorotitanic acid. The notified chemical is intended to be used
in industrial in metal coating formulations. Less than 1 tonne of the notified chemical will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data, the notified chemical is classified as hazardous under the
NOHSC Approved Criteria for Classifying Hazardous Substances. The classification and
labelling details are:
R26/27/28 Very toxic by inhalation, in contact with skin and if swallowed
R35 Causes severe burns.
S7/9 Keep container tightly closed and in a well-ventilated place.
S26 In case of contact with eyes, rinse immediately with plenty of water and
seek medical advice.
S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S45 In case of accident or if you feel unwell, seek medical advice immediately
(show the label where possible).
Occupational Health and Safety
The notified chemical poses an acceptable risk to occupational health and safety under the
conditions of the occupational settings described.
Public Health
The notified chemical poses a negligible risk to public health when used as an ingredient of
industrial metal coating formulations.
Environmental Effects
The notified chemical is not considered to pose a risk to the environment based on its
reported use pattern.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
22
RECOMMENDATIONS
Regulatory Controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- R26/27/28 Very toxic by inhalation, in contact with skin and if swallowed
- R35 Causes severe burns.
- S7/9 Keep container tightly closed and in a well-ventilated place.
- S26 In case of contact with eyes, rinse immediately with plenty of water and
seek medical advice.
- S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
- S45 In case of accident or if you feel unwell, seek medical advice
immediately (show the label where possible).
? Use the following risk phrases for products/mixtures containing the notified chemical:
- 10%: R26/27/28 Very toxic by inhalation, in contact with skin and if
swallowed; R35 Causes severe burns.
- 7% conc <10%: R26/27/28 Very toxic by inhalation, in contact with skin and if
swallowed; R34 Causes burns.
- 5% conc <7%: R23/24/25 Toxic by inhalation, in contact with skin and if
swallowed; R34 Causes burns.
- 1% conc <5%: R23/24/25 Toxic by inhalation, in contact with skin and if
swallowed; R36/38 Irritating to eyes and skin.
- 0.1% conc <1%: R20/21/22 Harmful by inhalation, in contact with skin and if
swallowed.
? The notified chemical should be classified as follows under the ADG Code:
- Class 8 ?Corrosive (Subsidiary: Class 6.1)
- Packaging Group II
? Suppliers should label the notified chemical as a Class 8 dangerous good with the
signal word Corrosive and the risk and safety phrases listed above.
Exposure Standard
The NOHSC exposure standards for hydrogen fluoride (as F) of 3 ppm or 2.6 mg/m3
?br>
(TWA), and fluoride (as F) of 2.5 mg/m3 should be observed during handling and use
of the notified chemical.
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical as introduced:
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
23
- Local and general exhaust ventilation should be applied wherever vapours of HF or
the notified chemical may be expected to occur.
- Wherever possible, direct handling of the notified chemical should be avoided; rather,
some remote handling apparatus should be used.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical as introduced:
- Avoid contact with skin, eyes and clothing.
- Avoid breathing vapours or mists.
- A shower and eyewash station should be available.
- Avoid spills and splashing during use.
- After exposure, any contaminated PPE should be thoroughly cleaned before re-use.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced:
- HF-resistant gloves
- Face-shield
- Acid resistant clothing which protects the body, arms, legs and feet
- Respiratory protection suitable for inorganic acid vapours
- Full-body encapsulation, including face and respiration, is recommended in areas
where high-level exposure is probable.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? Atmospheric monitoring should be conducted to measure workplace concentrations
during formulation and use of the notified chemical.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
? Do not allow material or contaminated containers to enter drains, sewers or
watercourses.
Disposal
? The notified chemical in its oxide form should be disposed of to landfill.
Emergency procedures
? For small spillages, absorb or contain liquid with sand, earth or spill control material.
Shovel up and place in a labelled, sealable container for subsequent disposal. Put
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
24
leaking containers in a labelled drum or overdrum. Scrub contaminated surfaces with
detergent solution. Retain washings as contaminated waste.
? For large spillages, transfer to a labelled, sealable container for product recovery or
safe disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(1) of the Act; if
- the importation volume exceeds one tonne per annum notified chemical.
or
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
25
9 PUBLICATION SUMMARY REPORT
Chemical 2 in Petro Products
Summary Report
Reference No: STD/1088
Akzo Nobel Chemicals Pty Ltd of Suite 10, 89 High St Kew Victoria 3101 has submitted a
standard notification statement in support of their application for an assessment certificate for
Chemical 2 in Petro Products. The notified chemical is intended to be used in hard surface
(e.g. floors), metal, carpet and brewery cleaners and as a rinse aid (e.g. dishwashing
machines). The notified chemical will be reformulated into a number of products which are
then used as is or diluted for use. Thirty to 100 tonnes of the notified chemical will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
Based on the available data the notified chemical is classified as hazardous under the NOHSC
Approved Criteria for Classifying Hazardous Substances. The classification and labelling
details are:
R22: Harmful if swallowed
R41: Risk of serious eye damage
R43: May cause sensitisation by skin contact
and
As a comparison only, the classification of notified chemical using the Globally Harmonised
System for the Classification and Labelling of Chemicals (GHS) is presented below. This
system is not mandated in Australia and carries no legal status but is presented for
information purposes.
Acute toxicity Hazard category: 4 Hazard statement: Harmful if swallowed
Eye irritation Hazard category: 1 Hazard statement: Irreversible effects on the eye
Skin Sensitisation Hazard category: 1 Hazard statement: May cause allergic skin reaction
With respect to the environment, the notified chemical is classified as Chronic Category 3.
Occupational Health and Safety
There is Low Concern to occupational health and safety for formulation activities due to the
adequate engineering controls but High Concern for use of cleaning products by spraying as
use of adequate respiratory protection is unlikely in all cases.
Public Health
There is High Concern to public health when products are used in spray applications.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
26
Environmental Effects
On the basis of the PEC/PNEC ratio:
The chemical is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Regulatory controls
Hazard Classification and Labelling
? The NOHSC Chemicals Standards Sub-committee should consider the following
health hazard classification for the notified chemical:
- R22: Harmful if swallowed
- R41: Risk of serious eye damage
- R43: May cause sensitisation by skin contact
? Use the following risk phrases for products/mixtures containing the notified chemical:
- 25%: R22: Harmful if swallowed
- 10%: R41: Risk of serious eye damage
- 5% conc 10%: R36: Irritating to eyes
- 1%: R43: May cause sensitisation by skin contact
? The National Drugs and Poisons Standing Committee (NDPSC) should consider the
notified chemical for listing on the SUSDP.
? Products containing more than the percentage specified of notified chemical and
available to the public must carry the following warning statements and safety
directions on the label:
- 5%: Irritant, Avoid contact with eyes
- 1%: (Repeated) exposure may cause sensitisation, Avoid contact with skin;
Wear protective gloves when mixing or using
- Any percentage: Breathing spray mist is harmful and may cause an asthma-
like reaction, Avoid breathing spray mist.
Control Measures
Occupational Health and Safety
? Employers should implement the following engineering controls to minimise
occupational exposure to the notified chemical as introduced and in formulated
products:
- Local exhaust ventilation should be employed at sites of potential dust cloud
or aerosol generation.
? Employers should implement the following safe work practices to minimise
occupational exposure during handling of the notified chemical as diluted for use and
in formulated products:
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
27
- Cleaning by spray should be conducted in areas of good general ventilation
- Spills should be cleaned up promptly and placed in containers for disposal
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to the notified chemical as introduced, as
diluted for use, and in formulated products:
- Respiratory protection against imported powders where dust can be generated or in
the absence of local exhaust ventilation;
- Impervious gloves;
- Safety goggles or face shields
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? Atmospheric monitoring should be conducted periodically by formulators of cleaning
products to measure workplace concentrations of dust during formulation of the
notified chemical.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified chemical are classified as hazardous
to health in accordance with the NOHSC Approved Criteria for Classifying
Hazardous Substances, workplace practices and control procedures consistent with
provisions of State and Territory hazardous substances legislation must be in
operation.
Environment
Disposal
? The notified chemical should be disposed of by incineration or to landfill.
Emergency procedures
? Spills/release of the notified chemical should be physically contained, collected and
disposed of in an appropriate manner.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under Section 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
No additional secondary notification conditions are stipulated.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
28
10 PUBLICATION SUMMARY REPORT
Irgasta P16 and Polymer in Irgasta P18
Summary Report
Reference No: PLC/654
Ciba Specialty Chemicals Pty Ltd (ABN 97 005 061 469) of 235 Settlement Road,
Thomastown Victoria 3074 has submitted a polymer of low concern (PLC) notification
statement in support of their application for an assessment certificate for Irgastat P 16 and
Polymer in Irgastat P 18. The notified polymer is intended to be used as a component in
thermoplastic polymers to form finished articles (e.g. computer housing). Up to 10 tonnes of
the notified polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
No toxicological data were submitted. The notified polymer meets the PLC criteria and can
therefore be considered to be of low hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
29
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? The notified polymer should be disposed with domestic refuse according to local
regulations.
? Contaminated packaging should be recycled once completely emptied.
Emergency procedures
Spills/release of the notified polymer should be handled by sweeping or shoveling up. The
collected material should be placed in a sealable, labeled container and recycled if possible or
disposed of to landfill.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
30
11 PUBLICATION SUMMARY REPORT
Aqualoc HS-1
Summary Report
Reference No: PLC/666
Grace Australia Pty Ltd (41 080 660 117) of 1126 Sydney Road, Fawkner VIC 3060, has
submitted a polymer of low concern (PLC) notification statement in support of their
application for an assessment certificate for Aqualoc HS-1. The notified polymer is intended
to be used as concrete additive. Up to 1000 tonnes of the notified polymer will be imported
per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard. This is supported by toxicological data on 46% aqueous solution of the notified
polymer. All results were indicative of low hazard. The occurrence of lung congestion in the
acute toxicity study is considered not to be related to the notified polymer, as the route of
exposure in the study was oral. High molecular weight polymers can cause lung damage
(USEPA) but this is less likely in the case of this polymer as it is water-soluble.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer as described.
? If aerosols are formed during the use of the notified polymer, engineering and PPE
controls should be used to prevent inhalation exposure.
? Specific engineering controls, work practices or personal protective equipment may be
required and should be selected on the basis of all ingredients in the formulation
containing the notified polymer.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
31
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of by authorised landfill.
Emergency procedures
? Spills and/or accidental release of the notified polymer should be handled by physical
containment, with subsequent adsorption onto inert material such as sand (not
sawdust). Collect for disposal. Do not flush to sewer.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
32
12 PUBLICATION SUMMARY REPORT
Sekisui Techpolymer MBX Series
Summary Report
Reference No: PLC/669
Cintox Pty Ltd (ABN 85 096 197 885) of 121 Carlton Crescent, Summer Hill NSW, has
submitted a polymer of low concern (PLC) notification statement in support of their
application for an assessment certificate for "Sekisui Techpolymer MBX series". The notified
polymer is intended to be used as an additive in paint, ink and plastic articles, to alter their
light scattering and reflective characteristics. Five to ten tonnes of the notified polymer will
be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
No toxicology data have been provided for the notified polymer, but as it is notified under the
PLC criteria, it can be considered to be of low hazard. The notified polymer is likely to be not
bioavailable and non-toxic, due to its probable very high molecular weight, cross-linking and
water insolubility. The main risk of adverse health effects presented by the notified polymer
is from its small particle size.
The notified polymer is comprised primarily of inhalable particle sizes (<100 祄), with most
grades containing smaller particle sizes in the respirable range (<10 祄). The health effects
of inhalation exposure to the notified polymer are unknown. The notified polymer is unlikely
to be absorbed from the lung, so deposition in the deep lung is probable, combined with an
inability of the lungs to dislodge the particles. Inhaled particulates are known to interfere with
cell function in the airways, causing inflammatory-like reactions. Therefore, bronchial or
pulmonary irritation is possible following inhalation exposure to particles containing the
notified polymer, arising from deposition of water-insoluble particles in the lung.
Occupational Health and Safety
The notified polymer is not considered to pose a risk to occupational health and safety under
the conditions of the occupational settings described.
Public Health
There is negligible concern to public health when used in the proposed manner.
Environmental Effects
The notified polymer is not considered to pose a risk to the environment based on its reported
use pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
33
? Employers should implement the following engineering controls to minimise
occupational exposure to powders containing the notified polymer during handling:
- Local exhaust ventilation and adequate general ventilation should be applied at
sites where powders are handled.
? Employers should implement the following safe work practices to minimise
occupational exposure during the handling of powders containing the notified
polymer:
- Avoid the formation of airborne dusts.
? Employers should ensure that the following personal protective equipment is used by
workers to minimise occupational exposure to powders containing the notified
polymer:
- safety glasses, gloves and overalls.
- dust mask (adequate for respirable particle sizes).
? Guidance in selection of personal protective equipment can be obtained from
Australian, Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? The notified polymer should be disposed of to landfill.
Emergency procedures
? Spills/release of powders containing the notified polymer should be collected by
vacuum and bagged or placed in a sealed container.
? Spills/release of plastic pellets containing the notified polymer should be collected
with a broom and bagged.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- The notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
- The notified polymer is proposed for introduction in the form of porous particles,
where any proportion of the particle size is of respirable diameters (<10 祄).
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
34
- The workplace environment (including the use of protective equipment) where
respirable powders of the notified polymer will be handled differs significantly to
the conditions described in the notification statement.
- The notified polymer is intended for use in a product for cosmetic or personal use.
or
Under subsection 64(2) of the Act:
- If any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
35
13 PUBLICATION SUMMARY REPORT
Polymer in Lotader 4503 and Lotader 3430
Summary Report
Reference No: PLC/686
Arkema Pty Ltd (ABN 44 000 330 772) of Ground Floor, 600 Victoria Street, Richmond VIC
has submitted a polymer of low concern (PLC) notification statement in support of their
application for an assessment certificate for "Polymer in Lotader 4503 and Lotader 3430".
The notified polymer is intended to be used as an adhesion modifier for extrusion plastics in
the manufacturing of packaging, Australia-wide. Less than 200 tonnes of the notified polymer
will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
No toxicological data were submitted under the PLC notification category, and the notifier
has declared that they hold no information in regards to its possible toxicity. As the notified
polymer meets the PLC criteria, it can be considered to be of low hazard.
Occupational Health and Safety
The notified polymer is not expected to pose a significant risk to occupational health and
safety under the conditions of the occupational settings described.
Public Health
The notified polymer presents no significant risk to public health when used in the proposed
manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
? If the notified polymer is used in circumstances where respirable dusts containing it
may be formed, the appropriate engineering and personal respiratory protective
equipment should be implemented to prevent inhalation exposure of workers,
according to the hierarchy of controls.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
36
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? The notified polymer should be disposed of by authorised landfill.
Emergency procedures
? Spills and/or accidental release of the notified polymer should be handled by physical
collection and re-use to the maximum extent practicable. Residues may be swept,
whilst avoiding creating dust.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
- the number-average molecular weight (Mn) of the imported polymer is <10,000
Da.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
37
14 PUBLICATION SUMMARY REPORT
Polymer in AD0979P
Summary Report
Reference No: PLC/692
The Valspar (Australia) Corporation Pty Limited (ABN 82 000 039 396) of 203 Power Street
Glendenning NSW 2761 has submitted a polymer of low concern (PLC) notification
statement in support of their application for an assessment certificate for Polymer in
AK0979P. The notified polymer is intended to be used as a component of paint formulations
for industrial use at one site in NSW. Up to 100 tonnes of the notified polymer will be
manufactured per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
No toxicological data were submitted. The notified polymer meets the PLC criteria and can
therefore be considered to be of low hazard.
Occupational Health and Safety
There is low concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is negligible concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
38
Disposal
? The notified polymer should be disposed of by licensed hazardous waste disposal.
Emergency procedures
? Spills and/or accidental release of the notified polymer should be handled physical
containment, preventing entry into waterways. Adsorb using inert adsorbent (sand,
earth, vermiculite etc) and transfer to suitable drums for disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
39
15 PUBLICATION SUMMARY REPORT
Degalan LP 65/12
Summary Report
Reference No: PLC/694
Degussa Australia Pty Ltd (ABN 16 079 823 313) of 30 Commercial Drive, Dandenong VIC
3175 has submitted a polymer of low concern (PLC) notification statement in support of their
application for an assessment certificate for DEGALAN LP 65/12. The notified polymer is
intended to be used as Coating component. Up to 300 tonnes of the notified polymer will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
No toxicological data were submitted. The notified polymer meets the PLC criteria and can
therefore be considered to be of low hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is No Significant Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
40
Environment
Disposal
? The notified polymer should be disposed of by incineration or to landfill.
Emergency procedures
? Spills and/or accidental release of the notified polymer should be handled by physical
containment, collection and subsequent safe disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
41
16 PUBLICATION SUMMARY REPORT
Aqualoc HW-1B
Summary Report
Reference No: PLC/695
Grace Australia Pty Ltd (41 080 660 117) of 1126 Sydney Road, Fawkner VIC 3060 has
submitted a polymer of low concern (PLC) notification statement in support of their
application for an assessment certificate for AQUALOC HW-1B. The notified polymer is
intended to be used as Concrete additive. Up to 300 tonnes of the notified polymer will be
imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard. This is supported by toxicological endpoints observed in testing conducted on the
notified polymer and analogue polymer that contains same monomers.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
42
Environment
Disposal
? The notified polymer should be disposed of to landfill.
Emergency procedures
? Spills and/or accidental release of the notified polymer should be handled by physical
containment, collection and subsequent safe disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
43
17 PUBLICATION SUMMARY REPORT
Permapol 97-125
Summary Report
Reference No: SAPLC/56
PPG Industries Australia Pty Ltd (ABN: 82 055 500 939) of McNaughton Rd Clayton VIC
3168 has submitted a polymer of low concern (PLC) notification statement in support of
their application for a self-assessed assessment certificate for Permapol 97-125. The notified
polymer is intended to be used as a coating for applications in the aerospace industry. Up to
3 tonnes of the notified polymer will be imported per annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
No toxicological data were submitted. The notified polymer meets the PLC criteria and can
therefore be considered to be of low hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
44
Disposal
? The notified polymer should be disposed of by licensed waste contractor to
incineration or land fill.
Emergency procedures
? Spills/release of the notified polymer should be prevented from entering watercourses.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
45
18 PUBLICATION SUMMARY REPORT
Permapol P3.1E
Summary Report
Reference No: SAPLC/58
PPG Industries Australia Pty Ltd (ABN 82 055 500 939) of McNaughton Rd, Clayton VIC
3168 has submitted a polymer of low concern (PLC) notification statement in support of
their application for a self-assessed assessment certificate for Permapol P3.1E. The notified
polymer is intended to be used as sealants applied to aircraft in an industrial environment.
Up to 5 tonnes of the notified polymer will be imported per annum for each of the first five
years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard. This is supported by toxicological endpoints observed in testing conducted on the
notified polymer or analogue chemical.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? Service personnel should wear cotton or disposable gloves and ensure adequate
ventilation is present when removing spent printer cartridges containing the notified
polymer and during routine maintenance and repairs.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
46
? A copy of the MSDS should be easily accessible to employees.
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Environment
Disposal
? The notified polymer should be disposed of by licensed waste contractor to
incineration or land fill.
Emergency procedures
? Spills and/or accidental release of the notified polymer should be prevented from
entering watercourses.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
47
19 PUBLICATION SUMMARY REPORT
Polymer in Daicure DG-4K
Summary Report
Reference No: SAPLC/63
DIC Australia Pty. Ltd.(ABN 12 000 079 550) of 323 Chisholm Rd Auburn NSW 2144 has
submitted a polymer of low concern (PLC) notification statement in support of their
application for a self-assessed assessment certificate for Polymer in Daicure DG-4K. The
notified polymer is intended to be used as a component of a range of UV curable printing
inks. The notified polymer will not be manufactured in Australia. It will be imported by sea
as a component (15-30% (w/w)) of a range of UV curable printing inks. The finished
printing inks will be imported in 1 kg slip lid metal cans. Upon arrival at ports in Sydney
and/or Melbourne the notified polymer will be transported by road to the notifier's
warehouse where it will be stored under cover until such time that it is transported to up to
five companies throughout Australia. During use, printing workers will manually transfer
inks to ducts on the printing unit. Up to 3 tonnes of the notified polymer will be imported per
annum for each of the first five years.
ASSESSMENT OF PUBLIC, OCCUPATIONAL HEALTH AND SAFETY AND
ENVIRONMENTAL EFFECTS
Hazard Assessment
The notified polymer meets the PLC criteria and can therefore be considered to be of low
hazard.
Occupational Health and Safety
There is Low Concern to occupational health and safety under the conditions of the
occupational settings described.
Public Health
There is Negligible Concern to public health when used in the proposed manner.
Environmental Effects
The polymer is not considered to pose a risk to the environment based on its reported use
pattern.
RECOMMENDATIONS
Control Measures
Occupational Health and Safety
? No specific engineering controls, work practices or personal protective equipment are
required for the safe use of the notified polymer itself, however, these should be
selected on the basis of all ingredients in the formulation.
Guidance in selection of personal protective equipment can be obtained from Australian,
Australian/New Zealand or other approved standards.
? A copy of the MSDS should be easily accessible to employees.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
48
? If products and mixtures containing the notified polymer are classified as hazardous to
health in accordance with the NOHSC Approved Criteria for Classifying Hazardous
Substances, workplace practices and control procedures consistent with provisions of
State and Territory hazardous substances legislation must be in operation.
Disposal
? The notified polymer should be disposed of to landfill or incinerated.
? Empty containers should be sent to local recycling or waste disposal facilities.
Emergency procedures
? Spills/release of the imported product containing the notified polymer not be allowed
into drains or waterways. Spills should be handled by absorbing with sand or other
inert absorbent material and put into suitable container for disposal.
Secondary Notification
The Director of Chemicals Notification and Assessment must be notified in writing within 28
days by the notifier, other importer or manufacturer:
Under subsection 64(1) of the Act; if
- the notified polymer is introduced in a chemical form that does not meet the PLC
criteria.
or
Under subsection 64(2) of the Act:
- if any of the circumstances listed in the subsection arise.
The Director will then decide whether secondary notification is required.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
49
20 ACCESS TO FULL PUBLIC REPORT
NICNAS publishes a Full Public Report for each new chemical assessed. These reports
are available for inspection at our NICNAS office by appointment only at 334-336
Illawarra Road, Marrickville NSW 2204.
Reports can also be viewed and downloaded free of charge from our website at
http://www.nicnas.gov.au/. Copies of these reports may also be requested, free of charge,
by contacting the Administration Section of NICNAS by phone: (02) 8577 8870 or fax:
(02) 8577 8888.
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
50
21 LOW VOLUME CATEGORY PERMITS
The permits listed in Table 1 were issued to import or manufacture the following chemicals
under section 21U of the Industrial Chemicals (Notification and Assessment) Act 1989. Low
Volume Category Permits are approved for 36 months.
Table 1
Low Volume Category Permits
PERMIT COMPANY COMPANY CHEMICAL OR TRADE HAZARDOUS USE DATE
NUMBER NAME POSTCODE NAME SUBSTANCE
752 La 2018 Polyquaternium-59 Yes Component 22/3/07
Biosthetique in Hair Care
Australia Pty Product
Ltd
753 Symrise Pty 2099 2H-2,4a- Yes Fragrance in 26/3/07
Ltd Methanonaphthalene, domestic
1,3,4,5,6,7-hexahydro- and
7-methoxy-1,1,5,5- cosmetic
tetramethyl- end-use
products
754 Symrise Pty 2099 Cyclohexadecenone Yes Fragrance in 26/3/07
Ltd domestic
and
cosmetic
end-use
products
755 Symrise Pty 2099 4,7-Methano-1H- ND Fragrance in 26/3/07
Ltd indenecarboxaldehyde, dosmestic
3a,4,5,6,7,7a- and
hexahydro-, reaction cosmetic
products with Me Et end-use
ketone, acid- products
isomerised, reduced
756 Givaudan 2128 3-Cyclooctene-1- Yes Fragrance 11/04/07
Australia Pty methanol, -ethyl- ingredient
Limited
N.D.: not determined; insufficient data available to effect a health effects classification under
Approved Criteria [NOHSC:1008(1999)]
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
51
22 COMMERCIAL EVALUATION CATEGORY PERMIT
The permits listed in Table 2 were issued to import or manufacture the following chemicals
for commercial evaluation under section 21G of the Industrial Chemicals (Notification and
Assessment) Act 1989.
Table 2
Commercial Evaluation Category Permits
PERMIT COMPANY COMPANY CHEMICAL HAZARDOUS QUANTITY USE PERIOD
NUMBER NAME POSTCODE OR TRADE SUBSTANCE APPROVED
NAME
Yes 4000 kg Component 2 years
686 Hawker de 3207 Benzenamine,
of epoxy
Havilland 4,4'-
resin
Aerospace methylenebis[
Pty Ltd 2-methyl-6-
(1-
methylethyl)-
1 year
ND 4000 kg Component
687 Cytec 2153 Polymer in
of putty for
Australia VIAPAL
the after-
Holdings Pty VUP 4693
market
Ltd E/68 automotive
industry
Yes 4000 kg Component 2 years
688 DIC Graphics 2144 Oxetane,
of ink
Australia Pty 3,3'[oxybis(m
Ltd ethylene)]bis[
3-ethyl-
1 year
Yes 4000 kg Component
689 3M Australia 2073 Component of
of cleaning
TM
Pty Ltd 3M General
productds
Purpose and
Neutral
Cleaners
1 year
ND 2000 kg Component
690 Pacific Resins 2130 Chemical in
of paint for
Pty Ltd Additol?XL
industrial
270
outdoor
application
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
52
23 EARLY INTRODUCTION PERMITS FOR NON-HAZARDOUS INDUSTRIAL
CHEMICALS
The permits listed in Table 3 were issued to import or manufacture the following chemicals
prior to the issue of their respective assessment certificates under section 30A of the Act.
Table 3
Early Introduction Permits
PERMIT COMPANY CHEMICAL OR USE
NUMBER NAME TRADE NAME
493 Cintox Pty Acrybase FCA-N3 Component of photocopier and
Ltd printer toner
494 The Valspar Polymer in AK1038P Component of paint formulations
(Australia) for industrial use
Corporation
Pty Ltd
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
53
24 NOTICE OF CHEMICALS ELIGIBLE FOR LISTING ON THE AUSTRALIAN
INVENTORY OF CHEMICAL SUBSTANCES FIVE YEARS AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 14(1) of the Industrial Chemicals (Notification
and Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 4
Chemicals Eligible for Listing on the Australian Inventory of Chemical Substances
CHEMICAL NAME MOLECULAR CAS
FORMULA NUMBER
2-Propenoic acid, telomer with N-(1,1- (C7H13NO4S.C7H13 927396-30-3
dimethylethyl)-2-propenamide, sodium NO.
C3H4O2.Na)x.C6H7
2-methyl-2-[(1-oxo-2-propen-1-
yl)amino]-1-propanesulfonate (1:1) and O2P.Na
sodium P-phenylphosphinate (1:1)
2-Propenoic acid, telomer with sodium P- C6H7O2P.(C3H4O2)x 927396-66-5
phenylphosphinate (1:1), sodium salt .xNa
Benzenesulfonic acid, mono- and di-C14- Unspecified 920526-46-1
20-branched alkyl derivs., calcium salts
Formaldehyde, polymer with (C15H16O2.C6H14O2 268214-80-8
(chloromethyl)oxirane, 2,2'-[1,2- S2.C6H6O.C3H5ClO
ethanediylbis(oxy)]bis[ethanethiol], 4,4'- .CH2O)x
(1-methylethylidene)bis[phenol] and
phenol
Ethanethiol, 2,2'-[1,2- C6H14O2S2 14970-87-7
ethanediylbis(oxy)]bis-
Ammonium (S,S')-ethylenediamine-N,N'- C10H12FeN2O8.H4N 158706-40-2
disuccinato(4-)ferrate(1-)
1,3-propanediamine, N, N''-1,2- Unspecified 191680-81-6
ethanediylbis-, reaction products with
cyclohexane and peroxidised n-butyl-
2,2,6,6-tetramethyl-4-piperidinamine-
2,4,6-trichloro-1,3,5-triazine reaction
products
Docosanoic acid, 2-(1-carboxyethoxy)-1- C28H52O6.Na 27847-75-2
methyl-2-oxoethyl ester, sodium salt
2-propenoic acid, 2-ethylhexyl ester, Unspecified 141091-65-8
polymer with ethenylbenzene and 2-
methyl-2-[(1-oxo-2-propenyl) amino]-1-
propanesulfonic acid, 2,2'-azobis[2-
methylbutanenitrile]-initiated
2-propanol, 1,1',1''-nitrilotris-, acetate C9H21NO3.C2H4O2 148691-66-1
(salt)
1H-Benzotriazole, sodium salt C6H5N3.Na 15217-42-2
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
54
1,3-Benzenedicarboxylic acid, polymer (C8H6O4.C6H10O4.C 67939-66-6
with hexanedioic acid, 2,2' 4H10O3.C3H8O2)x
oxybis[ethanol] and 1,2-propanediol
Sulfamic acid, reaction products with Unspecified 744198-58-1
bisphenol A-N-(1,3-
dimethylbutylidene)-N'-[2-[(1,3-
dimethylbutylidene)amino]ethyl]-1,2-
ethanediamine-2-(methylamino)ethanol
polymer and hydrolyzed bisphenol A-
epichlorohydrin polymer ether with
polyethylene glycol
2-Propenoic acid, telomer with sodium Unspecified 251567-48-3
hydrogen sulfite, ester with .alpha.-
methyl-.omega.-hydroxypoly(oxy-1,2-
ethanediyl), sodium salt, reaction
products with polyethylene glycol 2-
aminoethyl Me ether
Formaldehyde, polymer with 1,2- (C6H6O2.CH2O)x 25213-44-9
benzenediol
5-[4-(7-amino-1-hydroxy-3-sulpho- C28H25N5O12S.xLi 762263-42-3
napthalene-2-ylazo)-2,5-bis-(2-
hydroxyethoxy)-phenylazo]-isophthalic
acid, lithium salt
2-Propenoic acid, 2-methyl-, 2- (C12H22O2.C8H15N 900791-24-4
(dimethylamino)ethyl ester, polymer with O2.C7H12O3.C7H12
butyl 2-propenoate, 2-ethylhexyl 2- O2.C6H10O3)x
methyl-2-propenoate, 4-hydroxybutyl 2-
propenoate and 2-methoxyethyl 2-
propenoate
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
55
25 NOTICE OF CHEMICALS ELIGIBLE FOR IMMEDIATE LISTING ON THE
AUSTRALIAN INVENTORY OF CHEMICAL SUBSTANCES AFTER ISSUING OF
ASSESSMENT CERTIFICATES
Notice is given in accordance with section 13B of the Industrial Chemicals (Notification and
Assessment) Act 1989, that the following chemicals have been added to the Australian
Inventory of Chemical Substances.
Table 5
Chemicals Eligible for Immediate Listing on the Australian Inventory of Chemical
Substances
CHEMICAL NAME MOLECULAR CAS
FORMULA NUMBER
Unspecified 577954-20-2
2-Naphthalenesulfonic acid, 7-amino-4-hydroxy-
8-[[2-sulfo-4-[[2-
(sulfooxy)ethyl]sulfonyl]phenyl]azo]-, potassium
sodium salt, coupled with diazotized 2-[(4-
amino-5-methoxy-2-methylphenyl)sulfonyl]ethyl
hydrogen sulfate
Unspecified 214362-06-8
2-Naphthalenesulfonic acid, 7-amino-4-hydroxy,
coupled with diazotized 2-[(4-aminophenyl)
sulfonyl] ethyl hydrogen sulfate and diazotized 2-
amino-5-[[2-(sulfooxy) ethyl] sulfonyl]
benzenesulfonic acid, potassium sodium salts
C22H24N6O18S6.xK.
benzenesulfonic acid, 2,4-diamino-3-[[4-[[2- 187026-95-5
(sulfooxy)ethyl]sulfonyl]-phenyl]azo]-5-[[2- xNa
sulfo-4-[[2-(sulfooxy)ethyl]sulfonyl]phenyl]azo]-
, potassium sodium salt
Benzoic acid, 3,5-diamino-2-[(2- Unspecified 481066-69-7
sulfophenyl)azo]-, disodium salt, reaction
products with diazotized 2-[(4-
aminophenyl)sulfonyl]ethyl hydrogen sulfate,
sodium salts
Unspecified 849775-79-7
Siloxanes and Silicones, di-Me, 3-[dimethyl[2-
(trimethylammonio)ethyl]ammonio]propyl Me,
mono[[1-(3-hydroxypropyl)-1,3,3,3-
tetramethyldisiloxanyl]oxy]-terminated, ethers
with polyethylene glycol mono-Me ether, p-
toluenesulfonates
Chemical Gazette Commonwealth of Australia Gazette
No. C 05, 1 May 2007
|