MATERIAL SAFETY DATA SHEET
HAZARD KEY
0 FIRE HAZARD
4 - SEVERE
Quick-Sil ( Part B )
3 -SERIOUS
0
Manufacturer: F. E. Knight Inc.
HEALTH HAZARD
2 -MODERATE
Address: 120 Constitution Blvd.
Franklin, MA 02038
1 - SLIGHT
0 REACTIVITY
Telephone: 508-520-1666
0 - MINIMAL
Fax: 508-520-2402
Date Prepared: February 16, 1999
Emergency Chem-Tel: 1-800-255-3924
Telephone No: or 617-969-5399
Prepared by: Michael Knight
ccuracy or completeness of the data contained herein.
SECTION I - IDENTITY
Quick-Sil Part B
Common Name (Used on label)
(Trade name & Synonyms)
SECTION 2 - HAZARDOUS INGREDIENTS
HAZARDOUS COMPONENTS % OSHA PEL ACGIH TLV OTHER LIMITS
Silica (crystalline) 15 0.1 mg/m3 0.1 mg/m3 IARC listed
(Respirable (Respirable (SEE OTHER PRECAUTIONS)
Dust) Dust)
SECTION 3 - PHYSICAL & CHEMICAL CHARACTERISTICS
Boiling Point (掳C): N/A
Vapor Pressure (mmHg): Negligible (at 25 degrees C)
Vapor Density ( Air = 1 ): N/A
Specific Gravity: 1.15 (at 25 degrees C)
Melting Point (掳C): N/A
Evaporation Rate: Negligible (Butyl Acetate =1)
Solubility In Water: Not soluble
Appearance and Odor: Green and odorless paste
SECTION 4 - FIRE AND EXPLOSION HAZARD DATA
Flash Point (method used): 94 degrees C min. (open cup)
NSP-1
Flammable Limits: Not measured
Lower: Not measured
Upper: Not measured
EXTINGUISHING MEDIA:
Foam, dry chemical or carbon dioxide
SPECIAL FIRE FIGHTING PROCEDURES:
Not required
UNUSUAL FIRE AND EXPLOSION HAZARDS:
None
SECTION 5 - REACTIVITY DATA
Stability: Unstable
Conditions to Avoid: Avoid contact with acidic, basic and oxidizing materials.
Incompatibility (materials to avoid): Acidic, basic and oxidizing materials.
Hazardous Decomposition or By-Products: Flammable hydrogen gas.
Hazardous Polymerization: Will not occur
Conditions to Avoid: None
SECTION 6 - HEALTH HAZARD DATA
Route(s) of Entry: Inhalation ?: [-] Skin ?: [Y] Ingestion ?: [Y]
Health Hazards: Acute: No information is available
Chronic: No information is available
CARCINOGENICITY NTP ?: [N] IARC Monographs ?: [N] OSHA Regulated ?: [N]
Signs and Symptoms of Exposure:
Skin Contact: May cause slight irritation, but no significant effect.
Eyes Contact: May cause slight irritation.
Ingestion: No information is available.
Medical Conditions Generally Aggravated By Exposure:
No information is available
Emergency and First Aid Procedures:
Skin Contact: Remove paste from skin with dry cloth or towel, and wash exposed area with detergent.
Eyes Contact: Immediately flush with plenty of water for at least 15 minutes.
Ingestion: Do not induce vomiting. Call a physician immediately.
SECTION 7 - CONTROL AND PROTECTIVE MEASURES
Respiratory Protection (specify type): Not required
Ventilation-
Local Exhaust: Not required
Mechanical (general): Not required
Special: Not required
Other: Not required
QS-B-1
NSP-2
Protective Gloves: Plastic film or rubber gloves
Eye Protection: Safety glasses
Other Protective Clothing or Equipment: Eyewash equipment
Work/Hygienic Practices: Wash hands after handling
SECTION 8 - PRECAUTIONS FOR SAFE HANDLING AND USE
Steps To Be Taken In Case Material Is Released Or Spilled:
Contain the spill or leak.
Scrape up with cardboard or rag and place in container, in such a case pay attention to generation of hydrogen gas
by contaiminants.
Waste Disposal Method:
Can be burned in accordance with regulations.
Precautions To Be Taken In Handling And Storing:
Keep container closed when not in use.
Store in a cool place.
Keep away from heat and flame.
Don't lay the container on its side.
Avoid contact with eyes and prolonged or repeated skin contact.
OTHER PRECAUTIONS:
* This product contains crystalline silica which is considered a hazard by inhalation with dust and classified
as an agent which is probably carcinogenic to humans by IARC.
But we consider that this product doesn't fall under Group 2A in IARC because it doesn't generate the dust
under normal handling condition.
* Remarks: 1. Route(s) of entry / "Y" means "Yes".
2. Carcinogenicity / "N" means "No".
OTHER INFORMATION:
This materials safety data sheet is offered solely for your information, consideration and investigation. The data described in
this MSDS consist of data on literature, our acquisitional data and analogical inference by data of similar chemical substance
or product. F.E. Knight, Inc., provides no warranties, either express or implied, and assumes no responsibility for the
accuracy or completeness of the data contained herein.
QS-B-2
QS-B-3
NSP-3
|