Bodine Part No. 05200038 (aka LG-38)
Sold as Part No. 51700011
--------------------------------------------------------------------------
641050-00 MOBILUX EP 023
MATERIAL SAFETY DATA BULLETIN
--------------------------------------------------------------------------
--------------------------------------------------------------------------
1. PRODUCT AND COMPANY IDENTIFICATION
--------------------------------------------------------------------------
PRODUCT NAME: MOBILUX EP 023
SUPPLIER: EXXONMOBIL OIL CORPORATION
3225 GALLOWS RD.
FAIRFAX, VA 22037
24 - Hour Health and Safety Emergency (call collect): 609-737-4411
24 - Hour Transportation Emergency:
CHEMTREC: 800-424-9300 202-483-7616
LUBES AND FUELS: 281-834-3296
Product and Technical Information:
Lubricants and Specialties: 800-662-4525 800-443-9966
Fuels Products: 800-947-9147
MSDS Fax on Demand: 613-228-1467
MSDS Internet Website: http://emmsds.ihssolutions.com/
--------------------------------------------------------------------------
2. COMPOSITION/INFORMATION ON INGREDIENTS
--------------------------------------------------------------------------
CHEMICAL NAMES AND SYNONYMS: SEVERE TREAT MIN. OILS & ADDITIVES
GLOBALLY REPORTABLE MSDS INGREDIENTS:
Substance Name Approx. Wt%
-------------- -----------
ZINC DIALKYL DITHIOPHOSPHATE 1-5
(68457-79-4)
HYDROXYALKYL LONG-CHAIN <1
ALKENYL IMIDAZOLINE
(27136-73-8)
See Section 8 for exposure limits (if applicable).
--------------------------------------------------------------------------
3. HAZARDS IDENTIFICATION
--------------------------------------------------------------------------
Under normal conditions of use, this product is not considered hazardous
according to regulatory guidelines (See section 15).
EMERGENCY OVERVIEW: Brown Grease. DOT ERG No. : NA
POTENTIAL HEALTH EFFECTS: Under normal conditions of intended use,
this product does not pose a risk to health. Excessive exposure
may result in eye, skin or respiratory irritation.
POTENTIAL ENVIRONMENTAL EFFECTS: Harmful to aquatic organisms, may
cause long-term adverse effects in the aquatic environment.
For further health effects/toxicological data, see Section 11.
--------------------------------------------------------------------------
4. FIRST AID MEASURES
--------------------------------------------------------------------------
EYE CONTACT: Flush thoroughly with water. If irritation occurs, call
a physician.
SKIN CONTACT: Wash contact areas with soap and water. Remove and
clean oil soaked clothing daily and wash affected area.
INJECTION INJURY WARNING: If product is injected into or under
the skin, or into any part of the body, regardless of the
appearance of the wound or its size, the individual should be
evaluated immediately by a physician as a surgical emergency.
Even though initial symptoms from high pressure injection may be
minimal or absent, early surgical treatment within the first few
hours may significantly reduce the ultimate extent of injury.
INHALATION: Remove from further exposure. If respiratory irritation,
dizziness, nausea, or unconsciousness occurs, seek immediate
medical assistance. If breathing has stopped, assist ventilation
with mechanical device or use mouth-to-mouth resuscitation.
INGESTION: Not expected to be a problem. Seek medical attention if
discomfort occurs. Do not induce vomiting.
--------------------------------------------------------------------------
5. FIRE-FIGHTING MEASURES
--------------------------------------------------------------------------
EXTINGUISHING MEDIA: Carbon dioxide, foam, dry chemical and water fog.
SPECIAL FIRE FIGHTING PROCEDURES: Water or foam may cause frothing.
Use water to keep fire exposed containers cool. Water spray may
be used to flush spills away from exposure. Prevent runoff from
fire control or dilution from entering streams, sewers, or
drinking water supply.
SPECIAL PROTECTIVE EQUIPMENT: For fires in enclosed areas, fire
fighters must use self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS: None.
COMBUSTION PRODUCTS: Fumes, smoke, carbon monoxide, sulfur oxides,
aldehydes and other decomposition products, in the case of
incomplete combustion.
Flash Point C(F): > 204(400) (ESTIMATED FOR OIL, ASTM D-92 (COC)).
Flammable Limits (approx.% vol.in air) - LEL: NE, UEL: NE
NFPA HAZARD ID: Health: 0, Flammability: 1, Reactivity: 0
--------------------------------------------------------------------------
6. ACCIDENTAL RELEASE MEASURES
--------------------------------------------------------------------------
NOTIFICATION PROCEDURES: Report spills/releases as required to
appropriate authorities. U.S. Coast Guard and EPA regulations
require immediate reporting of spills/releases that could reach
any waterway including intermittent dry creeks. Report
spill/release to Coast Guard National Response Center toll free
number (800)424-8802. In case of accident or road spill notify
CHEMTREC (800) 424-9300.
PROCEDURES IF MATERIAL IS RELEASED OR SPILLED:
LAND SPILL: Shut off source taking normal safety precautions. Take
measures to minimize the effects on ground water. Recover by
pumping or contain spilled material with sand or other suitable
absorbent and remove mechanically into containers. If necessary,
dispose of adsorbed residues as directed in Section 13.
WATER SPILL: Confine the spill immediately with booms. Warn other
ships in the vicinity. Notify port and other relevant authorities.
Remove from the surface by skimming or with suitable absorbents. If
permitted by regulatory authorities the use of suitable dispersants
should be considered where recommended in local oil spill
procedures.
ENVIRONMENTAL PRECAUTIONS: Prevent material from entering sewers,
water sources or low lying areas; advise the relevant authorities
if it has, or if it contaminates soil/vegetation.
PERSONAL PRECAUTIONS: See Section 8
--------------------------------------------------------------------------
7. HANDLING AND STORAGE
--------------------------------------------------------------------------
HANDLING: High pressure injection under the skin may occur due to the
rupture of pressurized lines. Always seek medical attention. No
special precautions are necessary beyond normal good hygiene
practices. See Section 8 for additional personal protection
advice when handling this product.
STORAGE: Keep containers closed when not in use. Do not store in open
or unlabelled containers. Store away from strong oxidizing
agents and combustible materials. Do not store near heat,
sparks, flame or strong oxidants.
SPECIAL PRECAUTIONS: Prevent small spills and leakages to avoid slip
hazard.
EMPTY CONTAINER WARNING: Empty containers retain residue (liquid
and/or vapor) and can be dangerous. DO NOT PRESSURIZE, CUT, WELD,
BRAZE, SOLDER, DRILL, GRIND OR EXPOSE SUCH CONTAINERS TO HEAT,
FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION;
THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. Do not attempt to
refill or clean container since residue is difficult to remove.
Empty drums should be completely drained, properly bunged and
promptly returned to a drum reconditioner. All containers should
be disposed of in an environmentally safe manner and in
accordance with governmental regulations.
--------------------------------------------------------------------------
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
--------------------------------------------------------------------------
OCCUPATIONAL EXPOSURE LIMITS:
This product does not contain any components which have recognized
exposure limits.
VENTILATION: Use adequate ventilation.
RESPIRATORY PROTECTION: No special requirements under ordinary
conditions of use and with adequate ventilation.
EYE PROTECTION: Generally eye contact is unlikely with this type
material. If eye contact is likely, safety glasses with side
shields or chemical type goggles should be worn.
SKIN PROTECTION: If prolonged or repeated skin contact is likely, oil
impervious gloves should be worn. Good personal hygiene
practices should always be followed.
--------------------------------------------------------------------------
9. PHYSICAL AND CHEMICAL PROPERTIES
--------------------------------------------------------------------------
Typical physical properties are given below. Consult Product Data Sheet
for specific details.
APPEARANCE: Grease
COLOR: Brown
ODOR: Mild
ODOR THRESHOLD-ppm: NE
pH: NA
BOILING POINT C(F): > 316(600)
DROP POINT C(F): 121(250)
FLASH POINT C(F): > 204(400) (ESTIMATED FOR OIL, ASTM D-92 (COC))
FLAMMABILITY (solids): NE
AUTO FLAMMABILITY C(F): NA
EXPLOSIVE PROPERTIES: NA
OXIDIZING PROPERTIES: NA
VAPOR PRESSURE-mmHg 20 C: < 0.1
VAPOR DENSITY: NE
EVAPORATION RATE: NE
RELATIVE DENSITY, 15/4 C: 0.902
SOLUBILITY IN WATER: Negligible
PARTITION COEFFICIENT: > 3.5
VISCOSITY AT 40 C, cSt: 320.0
VISCOSITY AT 100 C, cSt: 25.0
POUR POINT C(F): NA
FREEZING POINT C(F): NE
VOLATILE ORGANIC COMPOUND: NE
NOTE: MOST PHYSICAL PROPERTIES FOR OIL COMPONENT.
DMSO EXTRACT, IP-346 (WT.%): <3, for mineral oil only
NA=NOT APPLICABLE NE=NOT ESTABLISHED D=DECOMPOSES
FOR FURTHER TECHNICAL INFORMATION, CONTACT YOUR MARKETING REPRESENTATIVE
--------------------------------------------------------------------------
10. STABILITY AND REACTIVITY
--------------------------------------------------------------------------
STABILITY (THERMAL, LIGHT, ETC.): Stable.
CONDITIONS TO AVOID: Extreme heat and high energy sources of ignition.
INCOMPATIBILITY (MATERIALS TO AVOID): Strong oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Product does not decompose at
ambient temperatures.
HAZARDOUS POLYMERIZATION: Will not occur.
--------------------------------------------------------------------------
11. TOXICOLOGICAL DATA
--------------------------------------------------------------------------
---ACUTE TOXICOLOGY---
ORAL TOXICITY (RATS): Practically non-toxic (LD50: greater than 2000
mg/kg). ---Based on testing of similar products and/or the
components.
DERMAL TOXICITY (RABBITS): Practically non-toxic (LD50: greater than
2000 mg/kg). ---Based on testing of similar products and/or the
components.
INHALATION TOXICITY (RATS): Practically non-toxic (LC50: greater
than 5 mg/l). ---Based on testing of similar products and/or the
components.
EYE IRRITATION (RABBITS): Practically non-irritating. (Draize score:
greater than 6 but 15 or less). ---Based on testing of similar
products and/or the components.
SKIN IRRITATION (RABBITS): Practically non-irritating. (Primary
Irritation Index: greater than 0.5 but less than 3). ---Based
on testing of similar products and/or the components.
OTHER ACUTE TOXICITY DATA: Although an acute inhalation study was not
performed with this product, a variety of mineral oils and
synthetic base oils, such as those in this product have been
tested. These samples had virtually no effect other than a
nonspecific inflammatory response in the lung to the aerosolized
mineral oil. The presence of additives in other tested
formulations (in approximately the same amounts as in the present
formulation) did not alter the observed effects.
---SUBCHRONIC TOXICOLOGY (SUMMARY)---
No significant adverse effects were found in studies using repeated
dermal applications of similar formulations to the skin of
laboratory animals for 13 weeks at doses significantly higher
than those expected during normal industrial exposure. The
animals were evaluated extensively for effects of exposure
(hematology, serum chemistry, urinalysis, organ weights,
microscopic examination of tissues etc.).
---REPRODUCTIVE TOXICOLOGY (SUMMARY)---
No teratogenic effects would be expected from dermal exposure, based
on laboratory developmental toxicity studies of major components
in this formulation and/or materials of similar composition.
---CHRONIC TOXICOLOGY (SUMMARY)---
Repeated and/or prolonged exposure may cause irritation to the skin,
eyes or respiratory tract. For mineral base oils: Base oils in
this product are severely solvent refined and/or severely
hydrotreated. Chronic mouse skin painting studies of severely
treated oils showed no evidence of carcinogenic effects. These
results are confirmed on a continuing basis using various
screening methods such as Modified Ames Test, IP-346, and/or
other analytical methods. For synthetic base oils: The base
oils in this product have been tested in the Ames assay and other
tests of mutagenicity with negative results. These base oils are
not expected to be carcinogenic with chronic dermal exposures.
---SENSITIZATION (SUMMARY)---
Not expected to be sensitizing based on tests of this product,
components, or similar products.
--------------------------------------------------------------------------
12. ECOLOGICAL INFORMATION
--------------------------------------------------------------------------
ENVIRONMENTAL FATE AND EFFECTS:
This environmental assessment was conducted using information on the
individual components as no test data was available for this
specific formulation.
ECOTOXICITY: This product is expected to be harmful to aquatic
organisms. May cause long-term adverse effects in the aquatic
environment.
MOBILITY: Not established.
PERSISTENCE AND DEGRADABILITY: This product is expected to be
inherently biodegradable, as the principal components have been
shown to degrade at slow to moderate rates.
BIOACCUMULATIVE POTENTIAL: Not established.
--------------------------------------------------------------------------
13. DISPOSAL CONSIDERATIONS
--------------------------------------------------------------------------
WASTE DISPOSAL: Product is suitable for burning in an enclosed,
controlled burner for fuel value. Such burning may be limited
pursuant to the Resource Conservation and Recovery Act. In
addition, the product is suitable for processing by an approved
recycling facility or can be disposed of at an appropriate
government waste disposal facility. Use of these methods is
subject to user compliance with applicable laws and regulations
and consideration of product characteristics at time of disposal.
RCRA INFORMATION: The unused product, in our opinion, is not
specifically listed by the EPA as a hazardous waste (40 CFR,
Part 261D), nor is it formulated to contain materials which
are listed hazardous wastes. It does not exhibit the hazardous
characteristics of ignitability, corrosivity, or reactivity. The
unused product is not formulated with substances covered by the
Toxicity Characteristic Leaching Procedure (TCLP). However, used
product may be regulated.
--------------------------------------------------------------------------
14. TRANSPORT INFORMATION
--------------------------------------------------------------------------
USA DOT: NOT REGULATED BY USA DOT.
RID/ADR: NOT REGULATED BY RID/ADR.
IMO: NOT REGULATED BY IMO.
IATA: NOT REGULATED BY IATA.
--------------------------------------------------------------------------
15. REGULATORY INFORMATION
--------------------------------------------------------------------------
US OSHA HAZARD COMMUNICATION STANDARD: When used for its intended
purposes, this product is not classified as hazardous in
accordance with OSHA 29 CFR 1910.1200.
EU Labeling: Product is dangerous as defined by the European Union
Dangerous Substances/Preparations Directives.
Symbol: Not applicable.
Risk Phrase(s): R52/53.
Harmful to aquatic organisms, may cause long-term adverse effects in
the aquatic environment.
Safety Phrase(s): S61.
Avoid release to the environment. Refer to special
instructions/Safety data sheets.
Governmental Inventory Status: All components comply with TSCA,
EINECS/ELINCS and AICS.
U.S. Superfund Amendments and Reauthorization Act (SARA) Title III:
This product contains no "EXTREMELY HAZARDOUS SUBSTANCES".
SARA (311/312) REPORTABLE HAZARD CATEGORIES: None.
This product contains the following SARA (313) Toxic Release
Chemicals:
CHEMICAL NAME CAS NUMBER CONC.
--------------------------- -------------- -------
ZINC DIALKYL DITHIOPHOSPHATE 68457-79-4 1.4%
The following product ingredients are cited on the lists below:
CHEMICAL NAME CAS NUMBER LIST CITATIONS
------------- ---------- --------------
LITHIUM HYDROXIDE (0.01%) 1310-65-2 22
ZINC (ELEMENTAL ANALYSIS) (0.17%) 7440-66-6 22
LITHIUM-SOAP THICKENER (1.74%) 7620-77-1 22
ZINC DIALKYL DITHIOPHOSPHATE 68457-79-4 18, 20, 21, 22, 24,
(1.35%) 25
FATTY ACIDS, C16-22, LITHIUM SALTS 68783-36-8 22
(0.21%)
--- REGULATORY LISTS SEARCHED ---
1=ACGIH ALL 6=IARC 1 11=TSCA 4 16=CA P65 CARC 21=LA RTK
2=ACGIH A1 7=IARC 2A 12=TSCA 5a2 17=CA P65 REPRO 22=MI 293
3=ACGIH A2 8=IARC 2B 13=TSCA 5e 18=CA RTK 23=MN RTK
4=NTP CARC 9=OSHA CARC 14=TSCA 6 19=FL RTK 24=NJ RTK
5=NTP SUS 10=OSHA Z 15=TSCA 12b 20=IL RTK 25=PA RTK
26=RI RTK
Code key: CARC=Carcinogen; SUS=Suspected Carcinogen; REPRO=Reproductive
--------------------------------------------------------------------------
16. OTHER INFORMATION
--------------------------------------------------------------------------
USE: AUTOMOTIVE GREASE
NOTE: PRODUCTS OF EXXON MOBIL CORPORATION AND ITS AFFILIATED COMPANIES
ARE NOT FORMULATED TO CONTAIN PCBS.
Health studies have shown that many hydrocarbons pose potential human
health risks which may vary from person to person. Information provided
on this MSDS reflects intended use. This product should not be used for
other applications. In any case, the following advice should be
considered:
INDUSTRIAL LABEL
Under normal conditions of intended use, this product does not pose a
risk to health. Excessive exposure may result in eye, skin or
respiratory irritation. Always observe good hygiene measures. First
Aid: Wash skin with soap and water. Flush eyes with water. If
overcome by fumes or vapor, remove to fresh air. If ingested do not
induce vomiting. If symptoms persist seek medical assistance. Read
and understand the MSDS before using this product.
*************************************************************************
For Internal Use Only: MHC: 1* 1* 1* 1* 1*, MPPEC: A, TRN: 641050-00,
ELIS: 400017, CMCS97: 970023, REQ: US - MARKETING, SAFE USE: L
EHS Approval Date: 20OCT2003
*************************************************************************
Information given herein is offered in good faith as accurate, but
without guarantee. Conditions of use and suitability of the product for
particular uses are beyond our control; all risks of use of the product
are therefore assumed by the user and WE EXPRESSLY DISCLAIM ALL
WARRANTIES OF EVERY KIND AND NATURE, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN RESPECT TO THE
USE OR SUITABILITY OF THE PRODUCT. Nothing is intended as a
recommendation for uses which infringe valid patents or as extending
license under valid patents. Appropriate warnings and safe handling
procedures should be provided to handlers and users. Alteration of this
document is strictly prohibited. Except to the extent required by law,
republication or retransmission of this document, in whole or in part, is
not permitted. Exxon Mobil Corporation and its affiliated companies
assume no responsibility for accuracy of information unless the document
is the most current available from an official ExxonMobil distribution
system. Exxon Mobil Corporation and its affiliated companies neither
represent nor warrant that the format, content or product formulas
contained in this document comply with the laws of any other country
except the United States of America.
Prepared by: ExxonMobil Oil Corporation
Environmental Health and Safety Department, Clinton, USA
|