MATERIAL SAFETY DATA SHEET (MSDS)
SAFETY DATA SHEET (SDS)
MSDS Date: January 20, 2009
1. IDENTIFICATION OF SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING
IDENTIFICATION OF PREPARATION: G200 Prepreg
USE OF PREPARATION: Resin-impregnated woven fiberglass.
COMPANY IDENTIFICATION ISOLA USA Corp. PHONE: 480-963-0022
San Tan II Corporate Center FAX: 800-233-1068
3100 West Ray Road
Chandler, AZ 85226
MSDS PREPARED BY: Chemistry & Industrial Hygiene, Inc., (800) 420-9311, on the date shown above.
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations
of Canada and the MSDS contains all the information required by the Controlled Products Regulations.
EMERGENCY TELEPHONE (24 HOUR): 800-468-1263 (Infotrac)
2. COMPOSITION/INFORMATION ON INGREDIENTS
Hazard
MATERIAL CAS NUMBER EC NUMBER PERCENT
Classification
Woven Continuous Filament Glass
65997-17-3 266-046-0 35-60 Xi, R36/37/38
Fiber (E-glass)
Bismaleimide 13676-54-5 237-163-4 1-2.5% T, R23; Xi, R36/37/38
Proprietary Resin Blend Proprietary Proprietary 40-70% Not Classified
See Section 16 for details on Hazard Classifications.
Information regarding proprietary ingredients is available from the manufacturer upon request.
3. HAZARDS IDENTIFICATION
Canadian WHMIS for the preparation:
Class D, Division 2B - Toxic Material Causing Eye and Skin Irritation.
EU PREPARATION CLASSIFICATION (1999/45/EC): Irritant (Xi), R36/37/38
EMERGENCY OVERVIEW: Inhalation of product particulates or of residual solvent vapors may be harmful. May cause
skin sensitization.
POTENTIAL HEALTH EFFECTS: No information is available on this specific mixture as a whole. The information
presented is based on each of the components present at concentrations greater than 1% (0.1% for hazardous
substances other than those classified as Xn, Xi, or category 3 carcinogens, mutagens or toxic for reproduction).
Exposure to product may cause eye, skin and respiratory tract irritation, and possible skin sensitization. May be harmful if
swallowed. This product contains less than one percent total residual solvents (N,N-Dimethylformamide, Toluene, Methyl
Ethyl Ketone, Acetone, Propylene Glycol Monomethyl Ether, Ethylene Glycol). Exposure to residual vapors may cause
eye and respiratory tract irritation, effects on the central nervous system, kidneys, liver, and gastrointestinal tract, and can
G200 PREPREG Isola USA Corp.
Page 2 of 7 January 2009
HAZARDS IDENTIFICATION (continued)
Cause chemical pneumonitis. Repeated or prolonged exposure to residual vapors may cause dermatitis, have effects on
the blood and bone marrow, have effects on the liver resulting in impaired function, enhance hearing loss, and may cause
toxicity to human reproduction or development. Dust generated during routine handling, machining, grinding, or sawing
may cause mechanical irritation of skin, eyes, nose, and throat.
Machining, grinding or sawing this material may generate harmful dusts. Continuous filament glass fiber is not considered
fibrogenic; however, it is woven from E-Glass fibers which are listed by IARC as "special purpose glass fibers" and
designated as "possibility of carcinogenic in humans." See Section 8 for exposure controls.
ROUTES OF ENTRY: Dermal: YES Inhalation: POSSIBLE Ingestion: SLIGHT Injection: POSSIBLE
4. FIRST AID MEASURES
SEEK IMMEDIATE MEDICAL ATTENTION IF IRRITATION OCCURS.
INHALATION: Remove the person to fresh air. Treat respiratory distress as appropriate (artificial respiration, etc.)
Provide oxygen if necessary. If not breathing, give mouth-to-mouth resuscitation and seek immediate medical attention.
EYES: Immediately flush eyes with large amounts of temperate water for a minimum of 15 minutes. Consult an
ophthalmologist for a more detailed medical evaluation.
SKIN: Remove contaminated clothing. Wash skin thoroughly with mild soap and room temperature running water. DO
NOT rub or scratch irritated areas, as this may force fibers into the skin. Seek immediate medical attention if irritation
continues.
INGESTION: Not expected to be a significant route of exposure based on expected use. If ingestion occurs, seek
immediate medical attention.
SYMPTOMS OF EXPOSURE: May include irritation of the eyes, skin, and respiratory tract, allergic skin reaction,
confusion, cough, sore throat, dizziness, headache, nausea, unconsciousness, diarrhea, vomiting, and weakness.
5. FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA: Carbon dioxide, foam or dry chemical powder. Water may be ineffective as an extinguishing
medium, but can be used to cool fire-exposed containers. If using a fire extinguisher, make sure that it is an NFPA Class
B extinguisher (e.g. label rating will read AB, ABC or BC)
FIRE FIGHTING EQUIPMENT: Wear full bunker gear including a positive pressure self-contained breathing apparatus.
6. ACCIDENTAL RELEASE MEASURES
GENERAL: Under conditions of inadequate ventilation, explosive vapor concentrations may form. Avoid contact with
skin, eyes or clothing. Sweep or scrape into approved container for proper disposal. Avoid generating dusty conditions.
See Section 13 for Disposal Considerations.
7. HANDLING AND STORAGE
HANDLING: May contain residual volatile organic compounds. Avoid contact with eyes, skin and clothing. Do not eat,
drink, or smoke while handling this product. Use only in a well ventilated area. Avoid inhalation and ingestion. The use
of appropriate gloves is recommended to minimize the potential for skin contact (See Section 8). Provide adequate
ventilation to minimize exposure. Provide proper NIOSH- or local authority-approved respirators if exposure limits are
exceeded. Wash thoroughly after handling this product.
G200 PREPREG Isola USA Corp.
Page 3 of 7 January 2009
HANDLING AND STORAGE (continued)
STORAGE: Store in a tightly closed container in a cool, dry area. Avoid contact with incompatible materials. Keep from
ignition sources, such as sparks and flames. NO SMOKING.
8. EXPOSURE CONTROLS /PERSONAL PROTECTION
EXPOSURE LIMITS*
(a)
ACGIH TLV(b) NIOSH REL(c)
MATERIAL OSHA PEL
15 mg/m3(d) TWA(e)
1 f/cc(h) TWA(e) Fibers(i) 3 f/cc(h) TWA(e) Fibers(i)
Total Dust (PNOR)(f)
Woven continuous filament glass fibers
5 mg/m3(d) TWA(e) 5 mg/m3(d) TWA(e)
5 mg/m3(d) TWA(e)
(including special purpose glass fibers)
Inhalable Dust(g) Respirable Dust(g)
Respirable Dust(g)
Bismaleimide None Established None Established None Established
None Established None Established None Established
Proprietary Resin Blend
*See Section 15 for additional Occupational Exposure Limits (OELs).
(a) U.S. Department of Labor, Occupational Safety and Health Administration, permissible exposure limit (PEL); (b) American
Conference of Governmental Industrial Hygienists', threshold limit value (TLV); (c) National Institute for Occupational Safety and
Health, recommended exposure limit (REL); (d) milligrams per cubic meter; (e) time-weighted average over an 8-hour day, 40-hour
work week for OSHA PELs and ACGIH TLVs, or up to a 10-hour day, during a 40-hour work week for NIOSH RELs; (f) Particulates
Not Otherwise Regulated (PNOR); (g) particles in the size range that are hazardous when deposited in the gas-exchange region of the
lungs. (h) fibers per cubic centimeter; (i) Respirable fibers longer than 5 microns and having an aspect ratio of >3:1.
ENGINEERING CONTROLS:
Use local exhaust to minimize exposures and maintain airborne dust and vapor concentrations below occupational
exposure limits, especially where heating or machining/grinding/sawing operations occur.
PERSONAL PROTECTIVE EQUIPMENT:
RESPIRATORY PROTECTION: In the absence of adequate general or local ventilation, or other appropriate
engineering controls, use a NIOSH- or local authority-approved respirator appropriate for the contaminant if
exposure limits are exceeded. Consult an industrial hygienist for assistance as needed.
SKIN PROTECTION: Avoid skin contact! Use impervious gloves, and splash-resistant clean body-covering
clothing to minimize exposure. Due to the combination of chemical ingredients, an industrial hygienist should be
consulted to select appropriate glove material for specific product application. Wash contaminated clothing before
reuse.
EYE PROTECTION: Use chemical resistant goggles when handling, and safety glasses or a face shield when
machining, grinding or sawing.
WORK/HYGIENE PRACTICES: Good personal hygiene should be exercised by all users of this product to minimize
potential dermal and inhalation exposures.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Resin impregnated woven glass fibers
Odor: Not Applicable
Odor Threshold: Not Applicable
Boiling Point: Not Applicable
Flash Point: Not Applicable
G200 PREPREG Isola USA Corp.
Page 4 of 7 January 2009
PHYSICAL AND CHEMICAL PROPERTIES (continued)
Auto-ignition Temperature: Not Determined
Lower Explosive Limit (LEL): Not Applicable Under Foreseeable Uses
Upper Explosive Limit (UEL): Not Applicable Under Foreseeable Uses
Vapor Pressure: Not Applicable
Specific Gravity: Not Applicable
Total Volatile Organic Compounds (TVOC) (G/L): Not Applicable
Solubility in Water: Not Applicable
Partition Coefficient: Not Applicable
Viscosity of Solution: Not Applicable
Vapor density (Air=1.0): Not Applicable
Percent Volatility: Less than 1% Volatile Organic Compounds
10. STABILITY AND REACTIVITY
This material is stable under expected conditions of use, handling and storage.
CONDITIONS TO AVOID: Avoid exposure to excessive heat, flames, sparks and other ignition sources. Avoid contact
with incompatible materials. Avoid dust generation. Contact with incompatible materials may cause hazardous
polymerization with rapid or excessive heating.
INCOMPATIBLE MATERIALS: Strong acids, strong bases, strong oxidizers, amines, mercaptans, metal ions, alcohols,
and phenols. This product may attack some plastic materials.
HAZARDOUS DECOMPOSITION: Dense smoke, acrid vapors and fumes, aliphatic and aromatic hydrocarbons
of variable composition, Hydrogen Cyanide, Bromine, Hydrogen Bromide, COX, and NOX.
EXOTHERMIC REACTION FIGHTING PROCEDURES: Dissipate heat by spreading material apart and dousing with
water. Contain vapors with local exhaust.
11. TOXICOLOGICAL INFORMATION
NO DATA AVAILABLE ON THE SPECIFIC MIXTURE.
CONTINUOUS FILAMENT GLASS FIBERS
NIOSH RTECS No.: LK3651000
Acute Effects of Overexposure: Exposure to dust may cause irritation to the eyes, skin and respiratory system, and
may cause difficulty breathing.
Chronic Effects of Overexposure: Repeated or prolonged contact with skin may cause dermatitis. Tumors have been
detected in experimental animals but may not be relevant to humans.
Target Organs: Eyes, skin, respiratory system.
Carcinogenicity: ACGIH A4, IARC Group 3
Special purpose glass fibers (E-Glass): ACGIH A3, IARC Group 2B
Toxicity Data: LD50 data not available in sources utilized.
Mouse-Intratracheal Lethal Dose > 20 mg/kg
G200 PREPREG Isola USA Corp.
Page 5 of 7 January 2009
TOXICOLOGICAL INFORMATION (continued)
BISMALEIMIDE
NIOSH RTECS No.: ON5670000
Acute Effects of Overexposure: May be fatal if inhaled. May cause eye, skin, and respiratory irritation. May be
harmful if swallowed.
Chronic Effects of Overexposure: No information available in sources utilized.
Target Organs: Respiratory system, eyes, and skin.
Carcinogenicity: Not listed as a carcinogen by IARC, ACGIH, NTP, OSHA, or NIOSH.
Toxicity Data: Rat-Inhalation LC50 = 0.35 mg/L/4h
Rat-Oral LD50 > 5,000 mg/kg
Mouse-Oral LD50 > 5,000 mg/kg
PROPRIETARY RESIN BLEND
NIOSH RTECS No.: Not Listed.
Acute Effects of Overexposure: May cause eye, skin or respiratory irritation and possible sensitization.
Chronic Effects of Overexposure: No information available in sources utilized.
Target Organs: Skin, eyes.
Carcinogenicity: Not listed as a carcinogen by IARC, ACGIH, NTP, OSHA, or NIOSH.
Toxicity Data: Rabbit-Dermal LD50 > 2,000 mg/kg
Rat-Oral LD50 > 2,000 mg/kg
12. ECOLOGICAL INFORMATION
NO DATA AVAILABLE ON THE SPECIFIC MIXTURE.
CONTINUOUS FILAMENT GLASS FIBERS (E-GLASS)
Information not available in sources utilized.
BISMALEIMIDE
Information not available in sources utilized.
PROPRIETARY RESIN BLEND
Information not available in sources utilized.
13. DISPOSAL CONSIDERATIONS
GENERAL: Follow all applicable local, national, provincial, territorial, and international regulations. As supplied, this
material is not regulated as a hazardous waste under the US EPA Resource Conservation and Recovery Act (RCRA).
Refer to the European Waste Catalog (EWC) for appropriate waste code(s).
14. TRANSPORT INFORMATION
Not regulated by US DOT, ICAO/IATA, RID/ADR, IMDG, Canada TDG
15. REGULATORY INFORMATION
CANADIAN ENVIRONMENTAL PROTECTION ACT: All of the components of this product are listed on the Canadian
Domestic Substances List (DSL).
EPA TOXIC SUBSTANCES CONTROL ACT (TSCA) STATUS: All of the components of this product are listed on the
TSCA inventory.
G200 PREPREG Isola USA Corp.
Page 6 of 7 January 2009
REGULATORY INFORMATION (continued)
EUROPEAN INVENTORY OF EXISTING COMMERCIAL CHEMICAL SUBSTANCES (EINECS): All of the components
of this product are listed on the EINECS inventory, are no longer polymers (NLP), or are polymer exempt.
ADDITIONAL OCCUPONAL EXPOSURE LIMITS (OELs). There are currently no international OELs for the the
Proprietary Brominated Resin Blend or Proprietary Epoxy Resin. See Section 8 for OSHA, ACGIH and NIOSH OELs.
CONTINUOUS FILAMENT GLASS FIBERS
Country
(based on mineral wool)
Arab Republic of Egypt Not Listed
Australia Not Listed
Austria Not Listed
Austria Not Listed
Belgium Not Listed
Canada
-Alberta 1.0 f/cc 8-hour OEL
1 f/cc 8-hour TWA
-British Columbia 3
5 mg/m 8-hour TWA Inhalable Dust
-Manitoba, New Brunswick, Nova Scotia, See ACGIH TLV
Prince Edward Island
3 f/cc 8-hour OEL
-Northwest Territory
5 mg/m3 8-hour OEL (Total Mass)
1 f/cc TWAEV
-Ontario
5 mg/m3 TWAEV Inhalable Dust
10 mg/m3 VEMP (8-hour OEL)
-Quebec
-Saskatchewan Not Listed
10 mg/m3 8-hour OEL
-Yukon Territory
Denmark Not Listed
Finland Not Listed
France Not Listed
Germany Not Listed
Hungary Not Listed
India Not Listed
Italy Not Listed
Japan Not Listed
Mexico Not Listed
2 fibers/cm3 MAC-TGG
The Netherlands
Respirable Dust
New Zealand Not Listed
Norway Not Listed
The Philippines Not Listed
Poland Not Listed
Russia Not Listed
Sweden Not Listed
Switzerland Not Listed
G200 PREPREG Isola USA Corp.
Page 7 of 7 January 2009
ADDITIONAL OELs (continued)
CONTINUOUS FILAMENT GLASS FIBERS
Country
(based on mineral wool)
Thailand Not Listed
United Kingdom Not Listed
Argentina, Bulgaria, Colombia, Jordan, Korea,
See ACGIH TLV
New Zealand, Singapore, Vietnam
16. OTHER INFORMATION
HAZARD CLASSIFICATIONS: R-PHRASES:
T=Toxic R23-Toxic by inhalation
Xi=Irritant R36/37/38-Irritating to eyes, respiratory system and skin
Current MSDS Revision Date: January 20, 2009
Previous MSDS Date(s): November 8, 2005; February 1, 2002; December 7, 1998
NOTE: This product contains partially cured resin(s). Curing should only be performed in well-ventilated or closed
systems. In accordance with good industrial hygiene practices, handle with care and avoid unnecessary personal
contact.
DISCLAIMER: The information contained in this MSDS relates specifically to the product as a whole and may not be
valid if used in combination with other materials or in any specified process. The information on G200 is accurate to the
best of our knowledge but does not purport to be all inclusive and should only be used as a general guide. It is the user's
responsibility to ensure that the product will be suitable for particular usage. The user assumes all responsibility for
compliance with applicable Federal, State and Local Regulations. We do not accept liability for damage or loss that may
occur from the use of this information.
|