MATERIAL SAFETY DATA SHEET
POWER FOAM BRAVO
HMIS NFPA Personal protective equipment
Health 3 3
Fire Hazard 4 4
Reactivity 0 0
Version Number: 1 Preparation date: 2006-02-08
1. PRODUCT AND COMPANY IDENTIFICATION
Product name: POWER FOAM BRAVO
MSDS #: 114640002
Product code: 04640
Recommended use: Floor care.
Manufacturer, importer, supplier:
US Headquarters Canadian Headquarters
JohnsonDiversey, Inc. JohnsonDiversey - Canada, Inc.
8310 16th St. 2401 Bristol Circle
Sturtevant, Wisconsin 53177-0902 Oakville, Ontario L6H 6P1
Phone: 1-888-352-2249 Phone: 1-800-668-3131
MSDS Internet Address:
www.johnsondiversey.com
Emergency telephone number: 1-800-851-7145 (Prosar); 1-651-917-6133 (Int'l Prosar); 01-800-710-3400 (M閤ico)
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
DANGER. CORROSIVE. CAUSES SKIN AND EYE BURNS. HARMFUL OR FATAL IF SWALLOWED. CONTENTS UNDER PRESSURE.
Principle routes of exposure: Eye contact. Skin contact. Inhalation. Ingestion.
Eye contact: Corrosive. Causes permanent eye damage, including blindness.
Skin contact: Corrosive. May cause permanent damage.
Inhalation: May cause irritation and corrosive effects to nose, throat and respiratory tract.
Ingestion: Corrosive. Causes burns to mouth, throat and stomach.
3. COMPOSITION/INFORMATION ON INGREDIENTS
HAZARDOUS COMPONENTS
Ingredient(s) CAS # Weight % LD50 Oral LD50 Dermal LC50 Inhalation
2-butoxyethanol 111-76-2 5 - 10% 470 mg/kg (rat) 220 mg/kg (rabbit) 450 ppm (rat)
Sodium hydroxide 1310-73-2 1 - 5% 140 mg/kg (rat) Not available Not available
Monoethanolamine 141-43-5 1 - 5% 1720 mg/kg (rat) 1 mL/kg (rabbit) Not available
Isobutane 75-28-5 5 - 10% Not available Not available Not available
4. FIRST AID MEASURES
Eye contact: Immediately flush eyes with running water for at least 15-20 minutes, keeping eyelids open . Get medical
attention immediately.
Skin contact: Flush immediately with plenty of water for at least 15 minutes. Get medical attention immediately.
Inhalation: If breathing is affected, remove to fresh air. Get medical attention immediately.
Ingestion: Immediately drink one cupful of water or milk. DO NOT induce vomiting unless directed to do so by
medical personnel . Never give anything by mouth to an unconscious person. Call medical attendant,
medical doctor, or poison control center .
Aggravated Medical Conditions: Persons with pre-existing skin disorders may be more susceptable to irritating effects
5. FIRE-FIGHTING MEASURES
Suitable extinguishing media: Use dry chemical, CO2, water spray or "alcohol" foam.
Specific hazards: Aerosol product - Containers may rocket or explode in heat of fire. Keep product and empty container away
from heat and sources of ignition. NFPA 30B Level 1 Aerosol .
Unusual hazards: Corrosive material (See sections 8 and 10).
Specific methods: Aerosol Product - Containers may rocket or expode in heat of fire. Use water spray to keep fire-exposed
containers cool.
POWER FOAM BRAVO 1 of 4
Special protective equipment for firefighters: As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or
equivalent) and full protective gear
Extinguishing media which must not be used for safety reasons: No information available
6. ACCIDENTAL RELEASE MEASURES
Personal precautions: Use personal protective equipment
Environmental precautions Remove all sources of ignition. Sweep up and shovel into suitable containers for disposal. Use a water
and clean-up methods: rinse for final clean-up.
7. HANDLING AND STORAGE
Handling:
Avoid contact with skin, eyes and clothing. Avoid breathing vapors, mists or dusts . Wash thoroughly after handling. Remove and wash contaminated
clothing and footwear before re-use. Use only with adequate ventilation. Keep away from open flames, hot surfaces and sources of ignition. CONTENTS
UNDER PRESSURE. Do not puncture or incinerate. FOR COMMERCIAL AND INDUSTRIAL USE ONLY.
Storage:
Store in a cool, dry, well ventilated area away from heat or open flame. Protect from freezing. Pressurized container: protect from sunlight and do not
expose to temperatures exceeding 50 degrees C or 120 degrees F. Do not pierce or burn, even after use. Keep out of the reach of children. NFPA 30B
Level 1 Aerosol .
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering measures to reduce exposure:
Good general ventilation should be sufficient to control airborne levels. Respiratory protection is not required if good ventilation is maintained.
Personal Protective Equipment
Eye protection: Chemical splash goggles.
Hand protection: Chemical resistant gloves
Skin and body protection: Protective footwear. If major exposure is possible, wear suitable protective clothing and footwear.
Respiratory protection: In case of insufficient ventilation wear suitable respiratory equipment. A respiratory protection program that
meets OSHA's 29 CFR 1910.134 and ANSI Z88.2 requirements must be followed whenever workplace
conditions warrant a respirator's use.
Hygiene measures: Handle in accordance with good industrial hygiene and safety practice
Ingredient(s) CAS # ACGIH OSHA Mexico
2-butoxyethanol 111-76-2 20 ppm (TWA) Skin 75 ppm (STEL)
240 mg/m3 (TWA) 360 mg/m3 (STEL)
120 mg/m3 (TWA)
50 ppm (TWA)
26 ppm (TWA)
2 mg/m3 (Ceiling) 2 mg/m3 (TWA) 2 mg/m3 (Ceiling)
Sodium hydroxide 1310-73-2
15 mg/m3 (STEL)
Monoethanolamine 141-43-5 6 ppm (STEL) 3 ppm (TWA)
6 mg/m3 (TWA)
3 ppm (TWA) 6 ppm (STEL)
3 ppm (TWA)
8 mg/m3 (TWA)
9. PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Compressed gas Bulk density: 8.24
pH: 13 Dilution pH: NA
Appearance: Aerosol Vapor density: No information available
Color: Clear Colourless Evaporation rate: No information available
Odor: Solvent Boiling point/range: Not determined
Specific gravity: 0.99 Melting point/range: Not determined
Density: 0.99 Decomposition temperature: Not determined
VOC: 15.85 Autoignition temperature: No information available
Flash point: <20 (癋) <-7 (癈) Viscosity: No information available
Solubility: Soluble Partition coefficient (n-octanol/water): No information available
Solubility in other solvents: No information available
Flame Extension (inches): 0
Elemental Phosphorous: 0.11
10. STABILITY AND REACTIVITY
Stability: The product is stable
Polymerization: Hazardous polymerization does not occur.
Hazardous decomposition products: None reasonably foreseeable.
Materials to avoid: Acids. Metals .
POWER FOAM BRAVO 2 of 4
Conditions to avoid: Keep away from heat. Keep away from open flames, hot surfaces and sources of ignition. Do not freeze.
11. TOXICOLOGICAL INFORMATION
Acute toxicity Corrosive Oral LD50 estimated to be > 2000 mg/kg
Component Information: See Section 3
Chronic toxicity: None known
Specific effects
Carcinogenic effects: None known
Mutagenic effects: None known
Reproductive toxicity: None known
Target organ effects: None known
12. ECOLOGICAL INFORMATION
Environmental Information: When used for its intended purpose this product should not cause adverse effects in the environment
13. DISPOSAL CONSIDERATIONS
Waste from residues / unused products:
Dispose of according to all federal, state and local applicable regulations
RCRA Hazard Class: D001
14. TRANSPORT INFORMATION
DOT/TDG: Please refer to the Bill of Lading/receiving documents for up to date shipping information
15. REGULATORY INFORMATION
International Inventories
All components of this product are listed on the following inventories: U.S.A. (TSCA), Canada (DSL/NDSL), Australia (AICS), Korea (ECL), Philippines
(PICCS), China (IECSC).
U.S. Regulations
California Proposition 65: This product is not subject to the reporting requirements under California's Proposition 65
STATE RIGHT TO KNOW
Ingredient(s) CAS # MARTK: NJRTK: PARTK: RIRTK:
2-butoxyethanol 111-76-2 X X X X
Sodium hydroxide 1310-73-2 X X - X
Monoethanolamine 141-43-5 X X X X
Ethoxylated alkylphenol 68412-54-4 - - - -
Water 7732-18-5 - - - -
Isobutane 75-28-5 X X X -
CERCLA / SARA
Ingredient(s) CAS # Weight % CERCLA/SARA RQ (lbs) Section 302 TPQ (lbs) Section 313
2-butoxyethanol 111-76-2 5 - 10% X
Sodium hydroxide 1310-73-2 1 - 5% 1000
Ingredient(s) CAA HAP CAA ODS CWA Priority Pollutants
2-butoxyethanol X
SARA 311/312 Hazard Categories
Immediate: Y
Sudden Release of Pressure: Y
Canada
WHMIS hazard class: A Compressed gases, E Corrosive material .
Ingredient(s) CAS # NPRI
2-butoxyethanol 111-76-2 X
Ethoxylated alkylphenol 68412-54-4 X
POWER FOAM BRAVO 3 of 4
16. OTHER INFORMATION
Reason for revision: Not applicable
Prepared by: NAPRAC
Additional advice: None
Notice to Reader: This document has been prepared using data from sources considered technically reliable. It does not constitute a warranty, express
or implied, as to the accuracy of the information contained within. Actual conditions of use and handling are beyond seller's control. User is responsible
to evaluate all available information when using product for any particular use and to comply with all Federal, State, Provincial and Local laws and
regulations.
POWER FOAM BRAVO 4 of 4
|