CYCLO?INDUSTRIES, INC
MATERIAL SAFETY DATA SHEET
401 Maplewood Drive, Suite 18, Jupiter, FL 33458
Phone: (561) 775-9600
First Aid Emergency: (800) 752-7869 or 1 (312) 906-6194
Shipping Emergency: (800) 424-9300 or 1 (703) 527-3887
This MSDS is being provided to your company for the purpose of providing current health and safety
information to your management and for your employees who work with this product. Please read the
information on these sheets and then provide this information to those people at your company whose
responsibility it is to comply with FEDERAL, STATE and COMMUNITY RIGHT TO KNOW regulations.
Also, make this information available to any employee who requests it.
If Cyclo Industries, Inc. considers the formula of this product to be a trade secret, the exact chemical names
of the ingredient(s) and the percentages in which they are combined will not appear in the body of this sheet.
The exact composition is available upon request to physicians, industrial hygienists and other health
professionals.
Boiling Point: 212癋 (100篊) Specific Gravity: 1.0 gms/ml
Vapor Pressure: N/A Vapor Density: N/A
Percent Volatile By Volume (%): 98% Percent V.O.C. By Weight (%): 10%
Solubility in Water: Soluble pH: 12.5
Evaporation Rate (Butyl Acetate = 1): Less than 1
Appearance and Odor: Clear to slightly hazy liquid with citrus odor; pressurized
C-192 Cyclo?Max Clean MSDS -- Page 2 of 3
SECTION 3 -- HAZARDOUS INGREDIENTS
CAS Reg No. Material Percentage TLV (Units)
111-76-2 2 Butoxy Ethanol* 0 - 10 25 ppm (TWA) skin
50 ppm (PEL)
10213-79-3 Sodium Metasilicate 0 -5 None established
68131-39-5 Non-ionic surfactant 0 -5 None established
75-28-5 Isobutane 0 - 10 1000 ppm
* Indicates toxic chemical(s) subject to the reporting requirements of SARA Title III, Section 313 and of 40 CFR 372.
SECTION 4 -- FIRE AND EXPLOSION HAZARD DATA
Flash Point: <-20癋 (<-29篊) Method Used: (T.C.C.)
Extinguishing Media: Water, foam, carbon dioxide
Special Fire Fighting Procedures: None known
Unusual Fire and Explosion Hazards: Prolonged exposure to temperatures above 130癋 may cause cans
to burst.
SECTION 5 -- HEALTH HAZARD DATA
Effects of Overexposure:
Ingestion: Nausea and vomiting.
Inhalation: None known.
Skin Contact: None known.
Eye Contact: Mild Irritation.
Threshold Limit Value: Not determined.
First Aid Procedures:
Ingestion: Induce vomiting and contact physician if necessary.
Skin Contact: Wash with soap and water.
Inhalation: Remove to fresh air if necessary.
Eye Contact: Flush with plenty of water for at least 15 minutes. Contact a physician if irritation
persists.
SECTION 6 -- REACTIVITY DATA
Stability: Stable Conditions to Avoid: Temperatures above 130癋
Incompatibility (materials to avoid): None known.
Hazardous Decomposition Products: None known.
Hazardous Polymerization: Will not occur.
C-192 Cyclo?Max Clean MSDS -- Page 3 of 3
SECTION 7 -- SPECIAL PROTECTION INFORMATION
Respiratory Protection: Not normally required.
Ventilation:
Local Exhaust Rate: Recommended
Special: None
Mechanical (General): Acceptable
Steps To Be Taken In Case Material Is Released or Spilled: Pick up excess with absorbent material and
discard in accordance with regulations. Flush surfaces with water.
Waste Disposal Method: Waste must be disposed of according to local, state and federal regulations.
CERCLA (Superfund) Reportable Quantity (in lb.): Not determined.
RCRA Hazardous Waste No. (40 CFR 261.33): Not determined.
SECTION 9 -- SPECIAL PRECAUTIONS
Precautions To Be Taken In Handling and Storage: Contents under pressure. Do not store below 32癋 or
above 130癋. Do not puncture or incinerate containers. Do not use or store near heat, sparks or
open flame.
Other precautions: Keep this and all chemicals out of the reach of children.
Date entered: 4/5/95
Date revised: 5/6/02
Cyclo Industries, Inc. provides the information contained herein in good faith but makes no representation
as to its comprehensiveness or accuracy. Individuals receiving this information must exercise their
independent judgement in determining its appropriateness for a particular purpose. Cyclo Industries, Inc.
makes no representations or warranties, either expressed or implied, of merchantability, fitness for a
particular purpose with respect to the information set forth herein or to the product to which the information
refers. Accordingly, Cyclo Industries, Inc. will not be responsible for damages resulting from use of or
reliance upon this information.