WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
MATERIAL SAFETY DATA SHEET
TIMBER PRESERVER - PART A
HAZARDOUS ACCORDING TO CRITERIA OF WORKSAFE AUSTRALIA
COMPANY DETAILS
Company Name: AA FIBREGLASS SUPPLIES
Address: 48 Wyuna Court HEMMANT, QLD, 4174
Telephone Number: (07) 3893 2037
Fax: (07) 3893 0416
Emergency Telephone Number: 0418 991 337
PRODUCT IDENTIFICATION
Product Name: TIMBER PRESERVER ?PART A
UN Number: 1263
Dangerous Goods Class: 3 (3.1)
Subsidiary Risk: None
Hazchem Code: 3[Y]E
Poisons Schedule: S5
Packing Group: II
Use: Part A of two pack solvent based timber coating.
PHYSICAL DESCRIPTION/PROPERTIES
Specific Gravity (20 篊): 0.95
?br>
Boiling Point (癈): 80 - 145
Vapour Pressure (kPa): >1
?br>
Flash Point (癈): -1 (CC-lit)
Explosive Limits (% in air): LEL/UEL ?1.0 - 11.0
?br>
Melting Point (癈): Not available
Solubility in Water: Immiscible
Appearance, Odour: Colourless highly flammable liquid with a strong odour; does not
mix with water
Date Issued: January 2006 1
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
INGREDIENTS
CHEMICAL CAS NUMBER PROPORTION
ENTITY (Vol / Vol)
Synthetic Resins 30-60%
Solvents as toluene 108-88-3 30-60%
Solvent grades are less than 0.1% benzene content.
HEALTH HAZARD INFORMATION
ACCUTE HEALTH EFFECTS
SWALLOWED: Considered an unlikely route of entry in commercial/industrial environments.
The liquid may produce considerable gastrointestinal discomfort and may be
harmful or toxic if swallowed. Ingestion may result in nausea, pain and vomiting.
Vomit entering the lungs may cause potentially lethal chemical pneumonitis.
EYE: The liquid produces a high level of eye discomfort and is capable of causing pain
and severe conjunctivitis. Corneal injury may develop, with possible permanent
impairment of vision, if not promptly and adequately treated. The vapour is
discomforting to the eyes if exposure is prolonged. The material may produce
severe irritation to the eye causing pronounced inflammation. Repeated or
prolonged exposure to irritants may produce conjunctivitis.
SKIN: The liquid is discomforting to the skin and is capable of causing skin reactions
which may lead to dermatitis from repeated exposures over long periods. Open
cuts, abraded or irritated skin should not be exposed to this material. The material
may accentuate any pre-existing dermatitis condition. The material may cause
skin irritation after prolonged or repeated exposure and may produce a contact
dermatitis (nonallergic) This form of dermatitis is often characterised by skin
redness (erythema) and swelling the epidermis. Histologically there may be
intercellular oedema of the spongy layer (spongiosis) and intracellular oedema of
the epidermis.
INHALED: The vapour/mist is discomforting to the upper respiratory tract and lungs.
Inhalation hazard is increased at higher temperatures. Inhalation of high
concentrations of gas/vapour causes lung irritation with coughing and nausea,
central nervous depression with headache and dizziness, slowing of reflexes,
fatigue and unco-ordination. If exposure to highly concentrated solvent
atmosphere is prolonged this may lead to narcosis, unconsciousness, even coma
and possible death. Inhalation of vapour may aggravate a pre-existing respiratory
condition such as asthma, bronchitis, and emphysema.
Date Issued: January 2006 2
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
CHRONIC HEALTH EFFECTS
Principal routes of exposure are usually by inhalation of vapour/spray mist and skin contact with
the material. Chronic solvent inhalation exposures may result in nervous system impairment and
liver and blood changes [PATTYS] Prolonged or continuous skin contact with the liquid may
cause defatting with drying, cracking, irritation and dermatitis following. As with any chemical
product, contact with unprotected bare skin; inhalation of vapour, mist or dust in work place
atmosphere; or ingestion in any form, should be avoided by observing good occupational work
practice.
FIRST AID
SWALLOWED: Rinse mouth out with plenty of water. If poisoning occurs, contact a doctor or
Poisons Information Centre. If swallowed do not induce vomiting. Give a glass
of water. If spontaneous vomiting appears imminent or occurs, hold patients head
down, lower than their hips to help avoid possible aspiration of vomitus.
EYES: If this product comes in contact with the eyes:
Immediately hold eyes open and wash continuously for at least 15 minutes with
fresh running water. Ensure complete irrigation of the eye by keeping eyelids
apart and away from eye and moving the eyelids by occasionally lifting the upper
and lowed lids. Transport to doctor without delay. Removal of contact lenses
after an eye injury should only be undertaken by skilled personnel.
SKIN: If solids or aerosol mists are deposited upon the skin:
Wash affected areas thoroughly with soap and water if available. Remove any
adhering solids with industrial skin cleansing cream. DO NOT use solvents. Seek
medical attention in the event of irritation.
INHALED: If fumes or combustion products are inhaled:
Remove to fresh air. Lay patient down. Keep warm and rested. Prostheses such
as false teeth, which may block airway, should be removed, where possible, prior
to initiating first aid procedures.. If breathing is shallow or has stopped, ensure
clear airway and apply resuscitation, preferably with a demand valve resuscitator,
bag-valve mask device, or pocket mask as trained. Perform CPR if necessary.
Transport to hospital, or doctor.
Date Issued: January 2006 3
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
ADVICE TO DOCTOR
Following acute or short term repeated exposures to toluene:
Toluene is absorbed across the alveolar barrier, the blood/air mixture being 11.2/15.6 ( at 37 deg. C). The
order of toluene, in expired breath, is of the order of 18ppm following sustained exposure to 100ppm. The
tissue/blood proportion is 1/3 except in adipose where the proportion is 8/10. Metabolism by microsomal
mono-oxygenation, results in the production of hippuric acid. This may be detected in the urine in amounts
between 0.5 and 2.5g/24 hr which represents on average 0.8mg/gm of creatinine. The biological half life of
hippuric acid is in the order of 1-2 hours.
Primary threat to life from ingestion and/or inhalation, is respiratory failure.
Patients should quickly be evaluated for signs of respiratory distress (eg. Cyanosis, tachypnoea, intercostal
retraction, obtundation) and given oxygen. Patients with inadequate tidal volumes or poor arterial blood gases
(pO2 50mmHg) should be intubated. Arrhythmias complicate some hydrocarbon ingested and/or inhalation
and electrocardiographic evidence of myocardial injury has been reported; intravenous lines and cardiac
monitors should be established in obviously symptomatic patients. The lungs excrete inhaled solvents, so that
hyperventilation improves clearance. A chest X Ray should be taken immediately after stabilisation of
breathing and circulation to document aspiration and detect the presence of pneumothorax. Epinephrine
(adrenalin) is not recommended for treatment of bronchospasm because of potential myocardial sensitisation
to catecholamines. Inhaled cardioselective bronchodilators (eg. Alupent, Salbutamol) are the preferred agents,
with aminophylline a second choice. Lavage is indicated in patients who require decontamination; ensure use
of cuffed endotracheal tube in adult patients [Ellenhorn and Barceloux: Medical Toxicology]
BIOLOGICAL EXPOSURE INDEX ?BEI
These represent the determinants observed in specimens collected from a healthy worker exposed at the
Exposure Standard (ES or TLV)
Determinant Index Sampling Time Comments
1. Hippuric acid in urine 2.5gm/gm End of shift Last B, NS
creatinine 4 hours of shift
2. Toluene in venous blood 1mg/L End of shift SQ
3. Toluene in end-exhaled air End of shift SQ
NS: Non-specific determinant; also observed after exposure to other material
SQ: Semi-quantitative determinant ?Interpretation may be ambiguous; should be used as a screening test
or confirmatory test.
B: Background levels occur in specimens collected from subjects NOT exposed
Date Issued: January 2006 4
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
PRECAUTIONS FOR USE
EXPOSURE STANDARDS
It is the goal of the ACGIH (and other agencies) to recommend TLAs (or their equivalent) for all
substances for which there is evidence of health effects at airborne concentrations encountered in the
workplace. At this time no TLV has been established, even though this material may produce
adverse health effects (as evidence in animal experiments or clinical experience). Airborne
concentrations must be maintained as low as is practically possible and occupational exposure must
be kept to a minimum.
NOTE: The ACGIH occupational exposure standard for Particles Not Otherwise Classified
(P.N.O.C, s) does NOT apply. Exposed individuals are NOT reasonably expected to be warned, by
smell, that the Exposure Standard is being exceeded. Odour Safety Factor (OSF) is defined as:
OSF = Exposure Standard (TWA) ppm/ Odour Threshold Value (OTV) ppm Classified into classes
as follows:
Class OSF Description
A 550 Over 90% of exposed individuals are aware by smell that the
Exposure Standard (TLV-TWA for example) is being reached,
even when distracted by working activities
B 26-550 Idem for 50-90% of persons being distracted
C 1-26 Idem for less than 50% of persons being distracted
D 0.18-1 10-50% of persons aware of being tested perceive by smell that
the Exposure Standard is being reached
E <0.18 Idem for less than 10% of persons aware of being tested.
EXPOSURE STANDARDS FOR MIXTURE
"Worst Case" computer aided prediction of vapour components/concentrations:
Composite Exposure Standard for Mixture ( TWA) (mg/m3) :188mg/m3. If the breathing zone
concentration of ANY of the components listed below is exceeded, "Worst Case" considerations
deem the individual to be over overexposed.
Component Breathing Zone ppm Breathing Zone mg/m3 Mixture Conc: (%)
Toluene 50 188 60
Operations which produce a spray/mist or fume/dust, introduce particles to the breathing zone.
REPRODUCTIVE HEALTH GUIDELINES
Established occupational exposure limits frequently do not take into consideration reproductive end
points that are clearly below the thresholds for other toxic effects. Occupational reproductive
guidelines (ORGs) have been suggested as an additional standard. These have been established after
a literature search for reproductive no-observed-adverse effect-level (NOAEL) and the lowest?br>
observed-adverse-effect-level (LOAEL).
Date Issued: January 2006 5
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
In addition the US EPA's procedures for risk assessment for hazard identification and dose response
assessment as applied by NIOSH were used in the creation of such limits.
Ingredient ORG UF Endpoint CR TLV Adequate
Toluene 9.6mg/m3 10 D NA -
These exposure guidelines have been derived from a screening level of risk assessment and should
not be construed as unequivocally safe limits. ORGS represent an 8 hour time weighted average
unless specified otherwise.
CR ?Cancer Risk/10000; UF ?Uncertainty Factor:
TLV believed to be adequate to protect reproductive health:
LOD ?Limit of Detection
Toxic endpoints have also been identified as:
D ?Developmental; R ?Reproductive; TC Transplacental Carcinogen
Jankovic J., Drake F.: A Screening Method for Occupational Reproductive
American Industrial Hygiene Association Journal 57: 641-649 (1996)
INGREDIENT DATA
TOLUENE:
TLV TWA: 50ppm Skin;A4;BEI [ACGIH]
PEL: 8hr TWA 200ppm ; Ceiling Conc: 300ppm ; Max excursion: 500ppm for 10minutes[OSHS
Z2]
ES TWA: 100ppm, 377mg/m3; STEL: 150ppm, 565mg/m3 (Under Review)
PROPOSED CHANGE
ES TWA 50ppm, 191mg/m3; STEL 150ppm, 574 mg/m3 SKIN
TLVTWA: 50ppm, 188mg/m3 SKIN A4
Note: This substance has been classified by the ACGIH as A4 NOT classifiable as causing cancer in
humans.
OES TWA: 50ppm, 191mg/m3 ;STEL: 150ppm, 574mg/.m3 SKIN
MAK value: 50ppm, 190mg/m3
MAK Category II Peak Limitation: For substances with systemic effects and with a half-life in
humans ranging from two hours to shelf-length.
Allows excursions of 5 times the MAK value, for 30 minutes (on average), twice per shift.
MAK Group C: There is no reason to fear risk of damage to the developing embryo when MAK and
BAT values are observed.
MAK Values, and categories and groups are those recommended within the Federal Republic of
Germany
IDLH Level: 500ppm
Odour Threshold Value: 0.16-6.7 (detection), 1.9-69 (recognition)
NOTE: Detector tubes measuring in excess of 5 ppm, are available.
Exposure limits with "skin" notation indicate that vapour and liquid may be absorbed through intact
skin. Absorption by skin may readily exceed vapour inhalation exposure. Symptoms for skin
absorption are the same as for inhalation. Contact with eyes and mucous membranes may also
contribute to overall exposure and may also invalidate the exposure standard.
Date Issued: January 2006 6
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
High concentrations of toluene in the air produce depression of the central nervous system(CNS) in
humans. Intentional toluene exposure (glue-sniffing) at maternally-intoxicating concentration has
also produced birth defects. Foetotoxicity appears at levels associated with CNS narcosis and
probably occurs only in those with chronic toluene-induced kidney failure. Exposure at or below the
recommended TLV-TWA is thought to prevent transient headache and irritation, to provide a
measure of safety for possible disturbances to human reproduction, the prevention of reductions in
cognitive responses reported amongst humans inhaling greater than 40 ppm, and the significant risks
of hepatotoxic, behavioural and nervous system effects (including impaired reaction time and
incoordination). Although toluene/ethanol interactions are well recognised, the degree of protection
afforded by the TLV-TWA among drinkers is not known.
ENGINEERING CONTROLS
Use in a well ventilated area. Spraying to be carried out in conditions conforming to local state
regulations.. Unprotected personnel must vacate the spraying area. General exhaust is adequate
under normal operating conditions. Local exhaust ventilation may be required in special
circumstances. Correct fit is essential to ensure adequate protection. Provide adequate ventilation in
warehouses and enclosed storage areas. Air contaminants generated in the workplace possess
varying "escape" velocities which, in turn, determine the "capture velocities" of fresh circulating air
required to effectively remove the contaminant.
Type of contaminant: Air Speed:
1.Solvent, vapours, degreasing etc. evaporating from tank (in still air). 0.25-0.5m/s (50-100f/min.)
2.Aerosols, fumes from pouring operations, intermittent container 0.5-1m/s (100-200 f/min.)
filling, low speed conveyer transfers, welding, spray drift, plating acid
fumes, pickling (released at low velocity into zone of active generation)
3.Direct spray, spray painting in shallow booths, drum filling, conveyer 1-2.5m/s (200-500
f/min.)
loading, crusher dusts, gas discharge (active generation into zone of
rapid air motion)
4.Grinding, abrasive blasting, tumbling, high speed wheel generated 2.5-10m/s (500-2000f/min.)
dusts(released at high initial velocity into zone of very high rapid
air motion)
Within each range the appropriate value depends on:
Lower end of the range Upper end of the range
1: Room air currents minimal or favourable to capture 1: Disturbing room air currents
2: Contaminants of low toxicity or of nuisance value only 2: Contaminants of high toxicity
3: Intermittent, low production 3: High production, heavy use
4: Large hood or large air mass in motion 4: Small hood-local control only
Date Issued: January 2006 7
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
Simple theory shows that air velocity falls rapidly with distance away from the opening of a simple
extraction pipe. Velocity generally decreases with the square of distance from the extraction point ( in
simple cases ). Therefore the air speed at the extraction point should be adjusted, accordingly, after
reference to distance from the contaminating source. The air velocity at the extraction fan, for example,
should be a minimum of 1-2m/s (200-400 f/min) for extraction of solvents generated in a tank 2 meters
distant from the extraction point. Other mechanical considerations, producing performance deficits
within the extraction apparatus, make it essential that theoretical air velocities are multiplied by factors
of 10 or more when extraction systems are installed or used.
Inc confined spaces where there is inadequate ventilation, wear full-face air supplied breathing
apparatus.
PERSONAL PROTECTION
EYE: Safety glasses with side shields; or as requires, chemical goggles. Contact lenses
pose a special hazard; soft lenses may absorb irritants and all lenses concentrate
them.
HANDS/FEET: Barrier creams with polyethylene gloves or wear chemical protective gloves, eg.
PVC. Wear safety footwear.
OTHER: Overalls.
Eyewash unit.
RESPIRATOR: Respiratory protection may be required when ANY "Worst Case" vapour-phase
concentration is exceeded (see Computer Prediction in "Exposure Standards")
Protection Factor (Min) Half-Face Respirator Full-face Respirator
10 x ES A-AUS -
A-PAPR-AUS -
20 x ES - A-AUS
- A-PAPR-AUS
100 x ES - A-2
- A-PAPR-2
The local concentration of material, quantity and conditions of use determine the type of personal
protective equipment required. For further information consult site-specific CHEMWATCH data (if
available), or your Occupational Health and Safety Advisor.
Date Issued: January 2006 8
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
SAFE HANDLING INFORMATION
STORAGE AND TRANSPORT
SUITABLE CONTAINER
Check all containers are clearly labelled and free from leaks.
STORAGE INCOMAPTABILITY
Avoid storage with oxidisers
STORAGE REQUIREMENTS
Store in original containers in approved flame-proof area. No smoking, naked lights, heat
or ignition sources. DO NOT store in pits, depressions, basements or areas where
vapours may be trapped. Keep containers securely sealed. Store away from incompatible
materials in a fry cool, well ventilated area. Protect containers against physical damage
and check regularly for leaks.
TRANSPORTATION
Class 3 ?Flammable liquids shall not be loaded in the same vehicle or packed in the
same vehicle or packed in the same freight container with:
Class 1 ?Explosives
Class 2.1 ?Flammable gases (where both flammable liquids and flammable
gases are in bulk)
Class 2.3 ?Poisonous gases;
Class 4.2 ?Spontaneously combustible substances;
Class 5.1 ?Oxidising agents
Class 5.2 ?Organic Peroxides
Class 7 ?Radioactive Substances
SPILLS AND DISPOSAL
MINOR SPILLS
Remove all ignition sources. Clean up all spills immediately. Avoid breathing vapours and
contact with skin and eyes. Control personal contact by using protective equipment. Contain and
absorb small quantities with vermiculite or other absorbent material. Wipe up. Collect residues in
a flammable waste container.
Date Issued: January 2006 9
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
MAJOR SPILLS
Clear area of personnel and move upwind. Alert fire brigade and tell them location and nature of
hazard. May be violently or explosive reactive. Wear breathing apparatus plus protective gloves.
Prevent by any means available, spillage from entering drains or water courses. Consider
evacuation. No smoking, naked lights or ignition sources. Increase ventilation. Stop leak if safe
to do so. Water spray or fog may be used to disperse/absorb vapour. Contain spill with sand,
earth or vermiculite. Use only spark-free shovels and explosion proof equipment. Collect
recoverable pro duct into labelled containers for recycling. Absorb remaining product with sand,
earth or vermiculite. Collect solid residues and seal in labelled drums for disposal. Wash area
and prevent runoff into drains. If contamination of drains or waterways occurs, advise
emergency services.
DISPOSAL
Consult manufacturer for recycling options and recycle where possible.
Refer to State Land Waste Management Authority.
Incinerate residue at an approved site.
Recycle containers if possible, or dispose of in an authorised landfill.
FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
Alcohol stable foam.
Dry chemical powder
Carbon dioxide
Water spray or fog ?Large fires only.
FIRE FIGHTING
Alert Fire Brigade and tell them location and nature of hazard.
May be violently or explosively reactive.
Wear breathing apparatus plus protective gloves. Prevent by any means available spillage from
entering drains or water courses.
Consider evacuation (or protect in place)
Fight fire from a safe distance, with adequate cover.
If safe, switch off electrical equipment until vapour fire hazard removed.
Use water delivered as a fine spray to control the fire and cool adjacent area. Avoid spraying
water onto liquid pools.
Do not approach containers suspected to be hot.
Cool fire exposed containers with water spray from a protected location.
If safe to do so, remove containers from path of fire.
When any large container (including road and rail tankers) is involved in a fire, consider
evacuation by 500 metres in all directions.
Date Issued: January 2006 10
WANDIG P/L T/AS
AA Fibreglass Supplies
AA
48 Wyuna Court, Hemmant. QLD 4174, Australia
Phone: 07 3893 2037 - Fax: 07 3893 0416 - Mobile: 0418 991 337 - http://www.ecn.net.au/~aafg/
International Phone: 61 7 3893 2037 - International Fax: 61 7 3893 0416
FIRE/EXPLOSION HAZARD
Liquid and vapour are highly flammable. Severe fire hazard when exposed to heat, flame and/or
oxidisers. Vapour forms an explosive mixture with air. Severe explosion hazard, in the form of
vapour, when exposed to flame or spark. Vapour may travel a considerable distance to source of
ignition. Heating may cause expansion/decomposition with violent rupture of containers. On
combustion, may emit toxic fumes of carbon monoxide (CO). May emit clouds of acrid smoke.
Other combustion products include Carbon Dioxide (CO2)
FIRE INCOMPATABILITY
Avoid combination with oxidising agents i.e. nitrates, oxidising agents, chlorine bleaches, pool
chlorine etc. as ignition may result.
HAZCHEM
3[Y]E
EMERGENCY and CONTACT POINT
EMERGENCY 24 HOUR TELEPHONE: 0418 991 337
Or for specialist advise from the Technical Manager or the Technical Director
TEL: (07) 3893 2037 FAX: (07) 3893 0416 (business hours)
POISONS INFORMATION SERVICE: 13 11 26
Date Issued: January 2006 11
|