HMIS
H =2
MATERIAL SAFETY DATA SHEET F =3
R =1
PPE = See Section 8
VOC: Max. content less than 50 g/L
(catalyzed)
Section I
Manufacturer: Siplast, an Icopal Group Company
(800) 643-1591 or (800) 922-8800
Address: 1000 E. Rochelle Blvd., Irving, TX 75062-3940
Emergency Phone No.: CHEMTREC, (800) 424-9300 (U.S.), (703) 527-3887 (outside of U.S.)
Product Class: Liquid-applied Waterproofing System - Component
Trade Name: Pro Repair Mortar Resin
Section II - Ingredients
NTP/IRAC ACGIH OSHA PEL
Ingredient OSHA CARC. Percent TLV TWA
Methyl Methacrylate No 70 - 75 50 ppm 100 ppm
CAS #80-62-6
2-Ethylhexyl Acrylate No 10 - 15 10 ppm Not Available
CAS #103-11-7
1.1'-(p-Tolylimino)dipropan-2-ol No 1? Not Available Not Available
Unusual Fire or Explosion Hazards: When exposed
Section III - Physical Data
to high temperatures may produce hazardous
decomposition products such as carbon monoxide,
Appearance & Odor: Liquid, colorless, clear
carbon dioxide, and smoke.
Odor Threshold: Smell of Methylmethacrylate
Fire-Fighting Instructions: In case of fire, wear
Vapor Pressure: 47 hPa
respiratory protection. Use self-contained breathing
Density: Approximately 0,96 g/cm3
apparatus.
Solubility in H2O: Insoluble
Boiling Point: Approximately 212癋 (100癈)
Section V - Health Hazard Data
Viscosity: Efflux time approximately 9 -11 sec (DIN
cup 4 mm 20癈)
EMERGENCY AND HAZARDS OVERVIEW:
ROUTES OF ENTRY: Inhalation, skin, and eye contact.
Section IV - Fire and Explosion Data
Human Effects and Symptoms of Overexposure:
WARNING! FLAMMABLE.
DOT Category: UN1263
Harmful if inhaled, swallowed, or absorbed through
Flash Point: >50癋 (10癈)
the skin. Causes skin, eye, and respiratory irritation.
Hazard Class: 3
May cause skin and respiratory sensitization.
Packaging Group: II
This product contains:
Label: Flammable Liquid
Methyl methacrylate and 2-ethylhexyl acrylate cause
Autoignition Temperature: 536癋 (280癈)
skin, eye, and respiratory irritation. High
LEL %: 1.7 UEL %: 8.2 (for methyl Methacrylate)
concentrations can cause symptoms of central
Suitable Extinguishing Media: Carbon dioxide; foam
nervous system depression, such as headache,
water spray jet
nausea, dizziness, drowsiness, and confusion.
Extinguishing media that must be used for safety
reasons: Full water jet
Trade Name: Pro Repair Mortar Resin
Page Two
Both acrylates can cause dermal and respiratory INGESTION: Do not induce vomiting. Give two glasses
sensitization. Once a person is sensitized, contact of water to dilute stomach contents. Never give
with even a small amount may cause outbreaks of anything by mouth to an unconscious person.
dermatitis with symptoms such as skin redness, Consult a physician immediately.
itching, rash, and swelling. This can spread from the
hands or arms to other parts of the body. Persons
with respiratory sensitization can experience Section VI - Reactivity Data
symptoms of bronchial asthma such as wheezing,
difficult breathing, sneezing and runny or blocked Stability: Stable
nose at low airborne concentrations that have no Hazardous Decomposition Products: Carbon
effect on unsensitized people. IARC has classified 2- monoxide, carbon dioxide, oxides of nitrogen,
ethylhexyl acrylate as class 3, not classifiable as to hydrocarbon by-products, and black smoke.
its carcinogenicity to humans. Polymerization: Avoid high temperatures. Product
may polymerize at > 140癋 (60癈). Polymerization is
Various acrylates, which may cause skin, eye, and exothermic and may cause container damage and/or
respiratory irritation and sensitization. fire.
1,1'-(p-Tolylimino)-dipropan-2-ol which is toxic when Materials to Avoid: Avoid strong acids, bases, and
ingested or inhaled. oxidizing agents to avoid exothermic reactions.
Avoid initiators that produce free radicals, and avoid
1-Isopropyl-2,2dimethyltrimethylenediisobutyrate, peroxides and metal-ions.
which according to the manufacturer, may cause skin
irritation.
Section VII - Spill or Leak Procedures
Titanium dioxide, may cause mechanical irritation to
the eye and respiratory passages and has ACGIH
Personal precautions: Use personal protective
and OSHA exposure limits. However, this product is
clothing. Keep away from sources of ignition and
sold as a liquid preparation and, when used as
keep air circulating in the room.
intended, does not generate dust. Thus the product
Environmental precautions: Do not allow spilt
as such does not pose a respiration hazard
product to enter soil or waterways. Do not allow to
attributable to these components. IARC has
enter drains. At pollution of rivers, lake, or drainages,
classified titanium dioxide as class 3, not classifiable
the authorities in charge have to be informed
as to its carcinogenicity to humans.
according to the local legislation.
Methods for cleaning up/taking up:
Carcinogenicity:
Pick up mechanically. Soak up spilled material with
NTP: No
sawdust, sand, or a chemical binder, then fill in a
IARC: No
tightly closing container and dispose of by
OSHA: No
combustion in a combustion plant approved by
authorities. Clean contaminated floors and objects
Emergency and First Aid Procedures:
thoroughly, observing environmental regulations.
SKIN: Remove contaminated clothing and shoes.
When picked up, treat material as prescribed under
Wash with soap or mild detergent and large amounts
heading "Disposal."
of water. Do not use solvents or thinners. Get
medical attention if irritation occurs. Wash clothing
before reuse.
EYES: Hold eyes open and flush for at least 15
minutes with large amounts of water. Seek medical
attention.
INHALATION: Remove to fresh air immediately. If
breathing has stopped, give artificial respiration. If
breathing is difficult, administer oxygen. Consult
physician if irritation of respiratory passage occurs.
Trade Name: Pro Repair Mortar Resin
Page Three
Section IX - Special Precautions
Section VIII - Special Protection Information
Protection Clothing/Equipment: Handling:
Gloves: Chemical resistant gloves. Appropriate Safe Handling: Provide good ventilation when
Material - nitrile. handling large quantities.
Goggles: Tightly fitting safety glasses. Protection against fire and explosion: Emergency
Respiratory: In interiors and during exceeding of the cooling must be provided for the eventuality of a fire
air limit values, carrying of protective masks is in the vicinity. Do not smoke. Vapors can form an
absolutely necessary. explosive mixture with air.
Skin: Clothing as usual in the chemical industry. Storage:
General protective and hygiene measures: Do not Requirements for storage rooms and vessels:
eat, drink, or smoke during work time. Storage of Prevent penetration into the ground.
foodstuffs in workrooms is forbidden. Keep away Hints on storage assembly: Do not store together
from foodstuffs and beverages. Wash hands before
with: Oxidizing agents or Peroxides.
breaks and after work. Observe the usual
Further information on storage conditions: Keep
precautions when handling chemicals. Avoid contact
container tightly closed; open and handle with care.
with eyes and skin.
Keep container dry in a cool, well-ventilated place.
Protect from heat and direct sunlight.
The information and recommendations contained herein are, to the best of Siplast's knowledge and belief, accurate and reliable as of the date
issued. Siplast does not warrant or guarantee their accuracy or reliability, and should not be liable for any loss or damage arising out of the use
thereof. User should satisfy himself that he has all current data relevant to his particular use.
Rev 11/07
|