HMIS Ratings
Material Safety Data Sheet Health 2
Flammability 1
Reactivity 0
Protection X
1 Chemical Product and Company Identification
Manufacturer Information Dynaloy, Inc.
1910 South State Avenue
Indianapolis, IN 46203
Phone (317) 788-5694
Emergency Phone 1-800-424-9300
(CHEMTREC)
FOR INTERNATIONAL
CALLS
703-527-3887
Date Prepared 2004-Mar-29
Supercedes 2003-Jun-17
Product Identity Dynasolve CU-6
Product Code Number J001
Product Use Polyurethane Remover
Version # 1 .0
CAS # Mixture
2 Composition / Information on Ingredients
Exposure Limits
Ingredient Name CAS Number Wgt. % PEL-OSHA TLV-ACGIH Carcinogen
2-PYRROLIDINONE, 1-METHYL- 872-50-4 40 - 70 Not Established Not Established No
2(3H)-FURANONE, DIHYDRO 96-48-0 10 - 30 Not Established Not Established No
GLYCOL ETHER EPH 122-99-6 10 - 30 Not Established Not Established No
PROPANOL, 25498-49-1 5 - 10 Not Established Not Established No
[2-(2-METHOXYMETHYLETHOXY)METHYLETHOXY)-
PROPANOIC ACID, 3-ETHOXY-, 763-69-9 3-7 Not Established Not Established No
ETHYL ESTER
3 Hazards Identification
Potential Health Effects
Skin Prolonged and/or repeated skin contact with this product may cause irritation/dermatitis.
Eyes This product may cause irritation to the eyes. High concentration of product vapors can cause
severe irritation of eyes.
Inhalation Exposure to oil mist/fume/vapor may cause respiratory tract irritation. Excessive inhalation of
this product may cause headache, dizziness, blurred vision, nausea and vomiting.
Ingestion Ingestion can cause gastrointestinal irritation, nausea, vomiting and diarrhea.
Material Name DYNASOLVE CU-6 Print Date 29-Mar-2004
1/ 4
Hazard Statements
CAUTION: EYE AND SKIN IRRITANT.
4 First Aid Measures
First Aid
Skin For skin contact flush with large amounts of water while removing contaminated clothing.
Wash contaminated clothing before reuse. If irritation persists, get medical attention.
Eyes Flush immediately with water for at least 15 minutes. Do not rub eyes. If irritation persists get
medical attention.
Inhalation If inhalation of gas/fume/vapor/dust/mist from the material is excessive (air concentration is
greater than the TLV or health effects are noticed), immediately remove the affected person(s)
to fresh air. If symptoms persist, get medical attention.
Ingestion DO NOT induce vomiting unless directed to do so by medical personnel. Call a physician
immediately.
5 Fire Fighting Measures
Hazardous Combustion Products
Irritating and/or toxic gases may be emitted upon the products decomposition.
Extinguishing Media
Dry chemical (preferred), alcohol foam, water. Use water to cool fire-exposed containers and to protect personnel.
Fire Fighting Equipment/Instructions
Firefighters should wear full protective clothing including self contained breathing apparatus.
Flash Point 99 癈 (210癋) CC
6 Accidental Release Measures
Containment Procedures
Dike the spilled material, where this is possible. Absorb with inert absorbent such as dry clay, sand or diatomaceous
earth, commercial sorbents, or recover using pumps.
Clean-Up Procedures
Absorb spill with inert material. Shovel material into appropriate container for disposal.
7 Handling and Storage
Handling Procedures
As with all chemicals, good industrial hygiene practices should be followed when handling this material. Avoid getting
this material into contact with your skin and eyes.
Storage Procedures
Keep the container tightly closed and in a cool, well-ventilated place.
8 Exposure Controls / Personal Protection
Material Name DYNASOLVE CU-6 Print Date 29-Mar-2004
2/ 4
Engineering Controls
Use general ventilation and use local exhaust, where possible, in confined or enclosed spaces. Provide adequate local
exhaust ventilation to maintain worker exposure below exposure limits.
Personal Protective Equipment
Eyes/Face
Wear safety glasses; chemical goggles (if splashing is possible).
Skin
Use impervious gloves. Normal work clothing (long sleeved shirts and long pants) is recommended. Use of impervious
apron and boots are recommended where splashing of the chemical is likely.
Respiratory
Respiratory protection; not normally required for ambient air concentrations not exceeding the Occupational Exposure
Limit. If ventilation is not sufficient to effectively prevent buildup of vapors, appropriate NIOSH/MSHA respiratory protection
must be provided
General
Eye wash fountain and emergency showers are recommended. Use good industrial hygiene practices in handling this
material.
9 Physical & Chemical Properties
Boiling Point > 200 癈
Specific Gravity 1.06
Vapor Pressure < 1 mm Hg
Solubility (H2O) complete
VOC 8.76 lb/gal
10 Chemical Stability & Reactivity Information
Chemical Stability
Stable under normal conditions.
Hazardous Decomposition
None known. Irritating and/or toxic fumes and gases may be emitted upon the products decomposition.
Hazardous Polymerization
Will not occur.
Incompatibility
Strong oxidizing agents (peroxides, chlorine, strong acids).
11 Toxicological Information
Toxicological Information
No data available for this product.
Material Name DYNASOLVE CU-6 Print Date 29-Mar-2004
3/ 4
12 Ecological Information
Ecological Information
No data available for this product.
Environmental Effects
No data available for this product.
13 Disposal Considerations
Disposal Instructions
Dispose of waste material according to Local, State, Federal, and Provincial Environmental Regulations.
14 Transportation Information
General
This product is not regulated as a hazardous material by the United States (DOT) or Canadian (TDG) transportation
regulations.
US DOT HMR Information
Proper Shipping Name Not Regulated
15 Regulatory Information
US Federal Regulations
All components are on the U.S. EPA TSCA Inventory List.
CERCLA/SARA - Section 313 - Emission Reporting
2-PYRROLIDINONE, 1-METHYL-
ETHANOL, 2-(2-PHENOXYETHOXY)-
ETHYLENE GLYCOL PHENYL ETHER
State Regulations
Other state regulations may apply. Check individual state requirements.
California - Proposition 65 - Developmental Toxicity
2-PYRROLIDINONE, 1-METHYL-
16 Other Information
Disclaimer
NOTICE: The information presented herein is based on data considered to be accurate as of the date of preparation of
this Material Safety Data Sheet. However, MSDS may not be used as a commercial specification sheet of manufacturer
or seller, and no warranty or representation, expressed or implied, is made as to the accuracy or comprehensiveness of
the foregoing data and safety information, nor is any authorization given or implied to practice any patented invention
without a license. In addition, no responsibility can be assumed by vendor for any damage or injury resulting from
abnormal use, from any failure to adhere to recommended practices, or from any hazards inherent in the nature of the
product.
Prepared By Lauri Kirby, Technical
Support
Issue Date 29-Mar-2004
Material Name DYNASOLVE CU-6 Print Date 29-Mar-2004
4/ 4
|