MATERIAL SAFETY DATA SHEET
PRODUCT NAME: Epoxy.com PRODUCT #224 &225 TILE GROUT PART A HMIS
CODES: HFRP
PRODUCT CODE: 224 A 110B
SECTION 1: MANUFACTURER IDENTIFICATION
MANUFACTURER'S NAME: Epoxy Systems, Inc.
20774 West Pennsylvania Ave
ADDRESS:
Dunnellon, FL 34431
DATE PRINTED: 12/2008
EMERGENCY NUMBER: 1-800-633-8253
INFORMATION NUMBER: 1-352-489-1666 PREPARER: N. LAMBERT
SECTION 2: HAZARDOUS INGREDIENTS
ACGIH
OSHA PEL TLV WT % CARCINOGEN
CAS NUMBER
HAZARDOUS COMPONENTS
Epoxy Resin 25068-38-6 NE NE 70-90 NO
Propylene Glycol
Monomethyl Ether 107-98-2 100 ppm 100ppm 1-10 NO
Alkylene Carbonate 108-32-7 NE NE 1-10 NO
Depending on color, one or more of the following may be present:
Titanium Dioxide 13463-67-7 10 mg/m?1-5 NO
Black Iron Oxide 1317-61-9 10 ppm 10 mg/m? <1 NO
Red Iron Oxide 1332-37-2 10 ppm 10 mg/m?1-5 NO
Yellow Iron Oxide 51274-00-1 10 ppm 5 mg/m? <1 NO
The exposure limits shown above for pigments are for dust exposure. They are
not known to be hazardous after blended into a liquid. Wet sanding is
suggested to eliminate airborne dust, if product is machined or ground. The
only other exposure limits established for ingredients of this product apply
to nuisance dusts from inert fillers. These fillers are blended into a liquid
and pose no hazard as supplied.
Substances listed are present in concentration of 1% or greater, or 0.1% if
cited as a potential Carcinogen in the OSHA hazards communication standard.
Where proprietary ingredient is listed, the identity is available as provided
in 29 CFR 1910.1200.
NE - Not Established NA-Not Available
SECTION 3: PHYSICAL/CHEMICAL CHARACTERISTICS
Above 400?F
BOILING POINT
Approx. 3.5 (Air = 1)
VAPOR DENSITY
Less than 1 mm Hg @ 100?F
VAPOR PRESSURE
0.00
VOC
Very slight
SOLUBILITY IN WATER
Low viscosity pigmented liquid
APPEARANCE AND ODOR
with a mild, pleasant aroma
1.11
SPECIFIC GRAVITY (H20=1)
SECTION 4: FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: >200?F
METHOD USED: Closed Cup
FLAMMABLE LIMITS IN AIR BY VOLUME LOWER: Not determined
UPPER: Not determined
EXTINGUISHING MEDIA: Foam, dry chemical CO 2
MSDS 224/225 "A" Page 1
SECTION 4: FIRE AND EXPLOSION HAZARD DATA (CON'T)
OSHA FLAMMABILITY CLASSIFICATION: Combustible liquid, Class III A
SPECIAL FIRE FIGHTING PROCEDURES: Decomposition and/or products of combustion
may be toxic. Use self contained breathing equipment.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Decomposition and combustion products may
be toxic.
SECTION 5: REACTIVITY DATA
STABILITY: Normally Stable
CONDITIONS TO AVOID: Elevated temperatures.
INCOMPATIBILITY (MATERIALS TO AVOID): Avoid contact with strong oxidizing
agents, strong acids, strong bases. Mixing large quantities (1 gallon)
with amines or epoxy hardeners can cause heat build-up and hazardous
reaction.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS: Carbon Monoxide, Carbon Dioxide,
Phenolic Derivatives.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 6: HEALTH HAZARD DATA
HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
INHALATION: Exposure to vapors at elevated temperatures may cause
irritation to respiratory tract and difficulty breathing.
EYE: May cause irritation to the eyes.
SKIN: A single exposure to the skin is unlikely to result in harm.
SKIN ABSORPTION: Repeated exposure to the skin can cause sensitization.
INGESTION: Oral toxicity is low. No hazards expected from normal
industrial exposure.
HEALTH HAZARDS (ACUTE AND CHRONIC):
CARCINOGENICITY:
NTP CARCINOGEN: NO IARC MONOGRAPHS: NO OSHA REGULATED: NO
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Allergy, Eczema, or skin
conditions.
EMERGENCY AND FIRST AID PROCEDURES:
EYES: Flush at once with potable water for at least 15 minutes.
SKIN: Wash with soap and warm water. Remove contaminated clothes. Wash
before reuse. Destroy contaminated shoes.
INGESTION: Not likely to occur in normal handling. Give large quantities
of water and get medical attention.
INHALATION: Remove to fresh air. Administer oxygen if breathing is
difficult.
SECTION 7: PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Avoid contact.
Soak up with clay or other absorbent material. Place in covered container
for disposal.
WASTE DISPOSAL METHOD: Dispose in an approved incinerator or an approved
landfill.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Avoid contact.
OTHER PRECAUTIONS: Keep containers tightly closed when not in use. If
mixture of A and B are allowed to remain in the mixing vessel past the pot
life deadline, heat and a strong reaction will result. Grinding or other
abrasive action to cured film may develop Micro crystalline Silica dust.
Wear a dust mask during such operations.
MSDS 224/225 "A" Page 2
SECTION 8: CONTROL MEASURES
RESPIRATORY PROTECTION: Avoid breathing vapor mist or spray.
VENTILATION: Use with good ventilation.
PROTECTIVE GLOVES: Wear impervious gloves.
EYE PROTECTION: Wear splash-proof chemical goggles.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: Provide eye fountain and safety
shower.
WORK/HYGIENIC PRACTICES: Practice good industrial hygiene. Wash with soap
and water before eating, smoking, or using the restroom.
SECTION 9: REGULATORY INFORMATION
SARA TITLE III SECTION 313: Unless shown below, this product does not contain
chemicals subject to the reporting requirements of section 313 of the
Emergency Planning and Community Right to Know Act of 1986 and of 40 CFR
372:
CAS # Chemical Name Percent by Weight
None
PROP 65 (CARCINOGEN): Unless shown below, this product does not contain
chemicals known to the state of California to cause cancer.
CAS # Chemical Name Percent by Weight
None
PROP 65 (TERATOGENIC): Unless shown below, this product does not contain
chemicals known to the state of California to cause birth defects or other
reproductive harm.
CAS # Chemical Name Percent by Weight
None
PROP 65 (CARCINOGENIC & TERATOGENIC): Unless shown below, this product does
not contain chemicals known to the state of California to cause cancer or
birth defects or other reproductive harm.
CAS # Chemical Name Percent by Weight
None
HAZARDOUS WASTE INFORMATION: Unless shown below, this product is not a
hazardous waste according to definitions found in CFR-40.
STATE OF MICHIGAN CRITICAL MATERIALS: Unless shown below, this product does
not contain ingredients appearing on the State of Michigan Critical
Materials List.
CAS # Chemical Name Percent by Weight
None
D.O.T. PROPER SHIPPING NAME: Synthetic Resin Liquid
PROPER SHIPPING NAME: Synthetic Resin Liquid
HAZARD CLASS: non-hazardous
UN/NA ID NUMBER:
SECTION 10: DISCLAIMER
Data and recommendations presented herein are based upon our and other
researchers and are believed to be accurate. The products discussed are
distributed without warranty (expressed or implied) and the customer shall
make his own determination of suitability for his particular purpose.
MSDS 224/225 "A" Page 3
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: Epoxy.com PRODUCT #224 &225 TILE GROUT PART B HMIS
CODES: H FRP
Epoxy.com 224 225-B
PRODUCT CODE: 310C
SECTION 1: MANUFACTURER IDENTIFICATION
MANUFACTURER'S NAME: Epoxy Systems, Inc.
20774 West Pennsylvania Ave
ADDRESS:
Dunnellon, FL 34431
DATE PRINTED: 12/2008
EMERGENCY NUMBER: 1-800-633-8253
INFORMATION NUMBER: 1-352-489-1666 PREPARER: N. LAMBERT
SECTION 2: HAZARDOUS INGREDIENTS
ACGIH
OSHA PEL TLV WT % CARCINOGEN
HAZARDOUS COMPONENTS CAS NUMBER
TOFA 68953-36-6 NE NE 50-60 NO
Tetraethylenepentamine 112-57-2 NE NE 10-20 NO
Diethylenetriamine 111-40-0 1 ppm 4 mg/m?1-10 NO
Bisphenol A 80-05-7 NE NE 1-5 NO
Substances listed are present in concentration of 1% or greater, or 0.1% if
cited as a potential Carcinogen in the OSHA hazards communication standard.
Where proprietary ingredient is listed, the identity is available as provided
in 29 CFR 1910.1200.
NE - Not Established
SECTION 3: PHYSICAL/CHEMICAL CHARACTERISTICS
>300?F
BOILING POINT
NE
VAPOR DENSITY
0.00
VOC
Slight
SOLUBILITY IN WATER
Dark amber liquid with slight
APPEARANCE AND ODOR
ammoniacal odor
0.99
SPECIFIC GRAVITY (H20=1)
N/A
EVAPORATION RATE
SECTION 4: FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: >200?F
METHOD USED: Closed Cup
FLAMMABLE LIMITS IN AIR BY VOLUME LOWER: Not determined
UPPER: Not determined
EXTINGUISHING MEDIA: Foam, dry chemical, CO2
OSHA FLAMMABILITY CLASSIFICATION: Combustible liquid, Class III B
SPECIAL FIRE FIGHTING PROCEDURES: Wear positive pressure self contained
breathing equipment. Use water to cool containers exposed to fire. Water
may be an ineffective extinguishing agent.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Vapors are heavier than air and may
travel along the ground or be moved by ventilation to ignition sources at
locations distant from material handling point. Pressure may build up in
containers and create an explosion hazard.
Page 1
224/225 "B" MSDS
SECTION 5: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Not applicable
INCOMPATIBILITY (MATERIALS TO AVOID): Oxidizing agents, strong acids or bases
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS: Carbon monoxide, carbon dioxide,
nitrogen oxides and organic compounds
HAZARDOUS POLYMERIZATION: Will not occur
SECTION 6: HEALTH HAZARD DATA
HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
INHALATION: Headache, nausea, respiratory tract irritant.
SKIN: Severe irritation and possible skin sensitizer.
EYE: Can cause irritation, burning, tearing, redness, swelling and
possible chemical burns to the eyes.
SKIN ABSORPTION: Can cause chemical burns, redness and swelling.
INGESTION: Abdominal pain, nausea, vomiting, diarrhea, throat and mouth
burns.
HEALTH HAZARDS (ACUTE AND CHRONIC):
CARCINOGENICITY:
NTP CARCINOGEN: NO IARC MONOGRAPHS: NO OSHA REGULATED: NO
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Skin contact may
aggrevate existing dermatitis (skin condition). Over exposure to vapor or
mist may aggrevate existing respiratory conditions such as asthma,
bronchitis, or fibrotic respiratory disease.
EMERGENCY AND FIRST AID PROCEDURES:
EYES: Flush immediately for 15 minutes with large amounts of potable
water. DO NOT attempt to neutralize with chemical agents. Get
immediate medical attention.
SKIN: Flush immediately for 15 minutes with potable water. DO NOT attempt
to neutralize with chemical agents. Remove contaminated clothing.
Launder before reuse. Discard contaminated shoes. Get medical
attention if swelling and/or irritation occurs.
INGESTION: Give water to dilute stomach contents. DO NOT induce vomiting.
If vomiting occurs, give fluids again. Get immediate medical attention.
Do not give anything by mouth to an unconscious or convulsing person.
INHALATION: Remove to fresh air. Get medical attention if effects
persist.
OTHER INSTRUCTIONS: Swallowing this corrosive material may result in
severe ulceration, inflamation, and possible perforation of the upper
alimentary tract, with hemorrhage and fluid loss. Aspiration of this
product during induced emesis can result in severe lung injury. If
evacuation of stomach is necessary, use method least likely to cause
aspiration, such as gastric lavage after endotracheal intubation.
Contact a Poison Control Center for additional treatment information.
SECTION 7: PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Avoid contact.
Allow only personnel wearing goggles, neoprene or rubber gloves and
protective clothing to clean up spill. In confined areas a full face
respirator is recommended. Absorb spill with clay, diatomaceous earth or
other absorbent material. Place in disposal containers.
WASTE DISPOSAL METHOD: Dispose of in approved incinerator or an approved
landfill.
Page 2
224/225 "B" MSDS
SECTION 7: PRECAUTIONS FOR SAFE HANDLING AND USE (CON'T)
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Avoid contact. Keep
containers tightly closed when not in use. Do not remove labels from empty
containers. If mixtures of Part B and Part A are allowed to remain in the
mixing container past the pot life deadline, heat and a strong reaction
will result.
OTHER PRECAUTIONS: none
SECTION 8: CONTROL MEASURES
RESPIRATORY PROTECTION: If vapor or mist is generated and the occupational
exposure limit is exceeded, use appropriate NIOSH/MSHA approved self
contained breathing equipment or a full face respirator.
VENTILATION: Mechanical ventilation required if TLV is expected to be
exceeded in confined areas.
PROTECTIVE GLOVES: Neoprene or natural rubber gloves
EYE PROTECTION: Chemical goggles
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: Body covering clothes
WORK/HYGIENIC PRACTICES: Practice good industrial hygiene. Wash with soap
and water before eating, smoking, or using the restroom.
SECTION 9: REGULATORY INFORMATION
SARA TITLE III SECTION 313: Unless shown below, this product does not contain
chemicals subject to the reporting requirements of section 313 of the
Emergency Planning and Community Right to Know Act of 1986 and of 40 CFR
372:
CAS # Chemical Name Percent by Weight
None
PROP 65 (CARCINOGEN): Unless shown below, this product does not contain
chemicals known to the state of California to cause cancer.
CAS # Chemical Name Percent by Weight
None
PROP 65 (TERATOGENIC): Unless shown below, this product does not contain
chemicals known to the state of California to cause birth defects or other
reproductive harm.
CAS # Chemical Name Percent by Weight
None
PROP 65 (CARCINOGENIC & TERATOGENIC): Unless shown below, this product does
not contain chemicals known to the state of California to cause cancer or
birth defects or other reproductive harm.
CAS # Chemical Name Percent by Weight
None
HAZARDOUS WASTE INFORMATION: Unless shown below, this product is not a
hazardous waste according to definitions found in CFR-40.
STATE OF MICHIGAN CRITICAL MATERIALS: Unless shown below, this product does
not contain ingredients appearing on the State of Michigan Critical
Materials List.
CAS # Chemical Name Percent by Weight
None
Page 3
224/225 "B" MSDS
SECTION 9: REGULATORY INFORMATION (CON'T)
D.O.T. PROPER SHIPPING NAME: Caustic Alkali Liquid, N.O.S. (Modified Amido
Amines); 8; UN1719; PG III
PROPER SHIPPING NAME: Caustic Alkali Liquid, N.O.S. (Modified Amido Amines)
HAZARD CLASS: Class 8, Corrosive
UN/NA ID NUMBER: UN 1719
PACKING GROUP III
SECTION 10: DISCLAIMER
Data and recommendations presented herein are based upon our and other
researchers and are believed to be accurate. The products discussed are
distributed without warranty (expressed or implied) and the customer shall
make his own determination of suitability for his particular purpose.
Page 4
224/225 "B" MSDS
|