810564PM Page 1 of 6
11-20-2001
MATERIAL SAFETY DATA SHEET
REVISION DATE: 04-1-2001 SUPERSEDES: 08-21-2001
SECTION 1. CHEMICAL PRODUCT AND COMPANY IDS IDENTIFICATION
COMPANY INFORMATION
Global Coatings Division
H.B. Fuller Company
2900 Granada Lane
Oakdale,MN 55128
Phone: 651-236-3700
Medical Emergency Phone Numbs (24 Hours): 1-888-853-1758
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
PRODUCT INFORMATION
PRODUCT IDENTIFIER: 810564PM
PRODUCT NUMBER: IF1947T
PRODUCT DESCRIPTION: Powder coating
SECTION 2: COMPOSlTION/INFORMATION ON INGREDIENTS
Unlisted ingredients are not `hazardous' per the Occupational Safety and Health Administration Hazard Communication
Standard (29 CFR 1910.1200) and/or are not found on the Canadian Workplace Hazardous Materials Information System
ingredient disclosure list See Section 8 for any additional exposure limit guidelines.
Chemical Name CAS # PERCENT OSHA PEL
Epoxy resin 25036-25-3 50 - 70 Not established
Calcium carbonate 1317-65-3 10 - 30 TWA (Total dust) 15 MG/M3
TWA (Respirable dusty 5 MG/M3
Epoxy resin 28064-14-4 10 - 30 Not established
Bisphenol A 80-05-7 1-5 No established
Iron oxide 1332-37-2 1-5 TWA (as Fe) Fume 10 MG/M3
Aromatic amine 693-98-1 0.1-1 Not established
Crystalline silica 14808-60-7 0.1-1 TWA (Respirable dust) 0.1 MG/M3
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Dust clouds in air can be ignited by electric sparks, hot surfaces and open flame.
810564PM Page 2 of 6
11-20-2001
MATERIAL SAFETY DATA SHEET
Can cause skin imitation. May cause allergic skin reaction.
May cause an allergic respiratory reaction.
Harmful if swallowed.
Cancer hazard.
HMIS RATING: HEALTH -- 1 FLAMMABILITY -- 1 REACTIVITY -- 0
See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective equipment
recommendations.
POTENTIAL HEALTH EFFECTS BY ROUTE OF ENTRY
EYE: Can cause minor irritation, tearing and reddening. Can cause mechanical irritation if dusts are generated.
SKIN: Continued or prolonged contact may irritate the skin and cause a skin rash (dermatitis). May cause
sensitization.
Can cause light sensitivity that results in a skin rash when exposed to sunlight or ultraviolet light sources.
INHALATION: Can cause minor respiratory irritation Dust may be slightly irritating to the respiratory tract.
Inhalation of dusts produced during cuffing, grinding or sanding of this product may cause irritation of the
respiratory tract
May cause allergic respiratory reaction.
Overexposure to iron oxide dust/fume may cause siderosis. Overexposure to crystalline silica may cause silicosis.
INGESTION: Ingestion is not an anticipated route of exposure. Harmful if swallowed.
LONG-TERM (CHRONIC) HEALTH EFFECTS
TARGET ORGAN(S): Skin, Lungs
REGULATED CARCINOGEN STATUS:
Unless noted below, this product does not contain regulated levels of NTP, IARC, ACGIH, or OSHA listed
carcinogens.
Crystalline silica
EXISTING HEALTH CONDITIONS AFFECTED BY EXPOSURE: Skin disease including eczema and
sensitization; Lung disease
SECTION 4: FIRST AID MEASURES
IF IN EYES: Immediately flush eyes with plenty of water for at least 20 minutes retracting eyelids often. Tilt the
head to prevent chemical from transferring to the uncontaminated eye. Get immediate medical attention and
monitor the eye daily as advised by your physician Flush eye with water for 20 minutes. Get medical attention.
IF ON SKIN: Wash with soap and water. Remove contaminated clothing, launder immediately, and discard
contaminated leather goods. Get medical attention immediately.
If VAPORS INHALED: Remove to fresh air. Call a physician if symptoms persist.
IF SWALLOWED: No hazard in normal industrial use. Do not induce vomiting. Seek medical attention if
symptoms develop. Provide medical care provider with this MSDS.
SECTION 5: FIRE FIGHTING MEASURES
FLASH POINT: Not applicable
AUTOIGNITION TEMPERATURE: Not established
LOWER EXPLOSIVE LIMIT (% in air): Not established
UPPER EXPLOSIVE LIMIT (% in air): Not established
EXTINGUISHING MEDIA: Use water spray, foam, dry chemical or carbon dioxide.
810564PM Page 3 of 6
11-20-2001
MATERIAL SAFETY DATA SHEET
UNUSUAL FIRE AND EXPLOSION HAZARDS: Material will burn in a fire. Normal LEL for powder coatings
0.04 to 0.07 ounces/cubic foot. Strong explosions are not
expected below 0.4 to 0.7.
SPECIAL FIRE FIGHTING INSTRUCTIONS: Persons exposed to products of combustion should wear self
contained breathing apparatus and full protective equipment.
HAZARDOUS COMBUSTION PRODUCTS: Carbon dioxide, Carbon monoxide
SECTION 6: ACCIDENTAL RELEASE MEASURES
SPECIAL PROTECTION: No health effects expected from the cleanup of this material if contact can be
avoided. Follow personal protective equipment recommendations found in
Section 8 of this MSDS.
CLEAN-UP: Avoid creating dusts. Eliminate ignition sources. If a vacuum is used, ensure that
the material is wetted or otherwise treated so an explosive dust atmosphere is not
created within the vacuum.
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
SECTION 7: HANDLING AND STORAGE
Handling: Mildly irritating material. Avoid unnecessary exposure. Avoid creating dusts as an explosive dust air
mixture can be created at high concentrations. If dusts are created, ensure no sources of ignition are
present. Take precautionary measures to prevent electrostatic discharges.
Storage: Store in a cool, dry place.
Consult the Technical Data Sheet for specific storage instructions.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
EYE PROTECTION: Wear safety glasses with side shields when handling this product. Wear additional
eye protection such as chemical splash goggles and/or face shield when the
possibility exists for eye contact with splashing or spraying liquid, or airborne
material. Have an eye wash station available.
SKIN PROTECTION: Prevent contact with this product. Wear chemically resistant gloves, long sleeved
shirt, an apron, and other protective equipment depending on conditions of use.
GLOVES: Nitrite
RESPIRATORY PROTECTION: Respiratory protection may be required to avoid overexposure when handling this
product. Use a respirator if general room ventilation is not available or sufficient
to eliminate symptoms. NIOSH approved air ~ Expiator with dust/mist filter.
Respirators should be selected by and used following requirements found in
OSHA's respirator standard (29 CFR 1910.134).
VENTILATION:
EXPOSURE LIMITS:
Chemical Name ACGIH EXPOSURE LIMITS AIHA WEEL
Epoxy resin Not established Not established
Calcium carbonate TWA (Total dust) 10 MG/M3 Not established
810564PM Page 4 of 6
11-20-2001
MATERIAL SAFETY DATA SHEET
Epoxy resin Not established Not established
Bisphenol A Not established Not established
Iron oxide TWA (as Fe) Fume 5 MG/M3 Not established
Aromatic amine Not established Not established
Crystalline silica TWA (Respirable dust) 0.05 MG/M3 Not established
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Solid
COLOR: Red
ODOR: Neutral
ODOR THRESHOLD: Not established
WEIGHT PER GALLON (Ibs.): 11.58
SPECIFIC GRAVITY: 1.39
SOLIDS (% by weight): 100.0
Not applicable
pH: Not established
BOILING POINT (deg. C): Not established
FREEZING/MELTING POINT (dew C): Not established
VAPOR PRESSURE (mm Hg): Not established
VAPOR DENSITY: Not established
EVAPORATION RATE: Not established
OCTANOL/WATER COEFFICIENT: Not established
SECTION 10: STABILITY AND REACTIVITY
STABILITY: Stable under normal conditions.
CHEMICAL INCOMPATIBILITY: Not established
HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, Carbon dioxide
SECTION 11: TOXICOLOGICAL INFORMATION
CHEMICAL NAME LD50/LC50
Epoxy resin Oral LD50 Rat > 30 g/kg
Inhalation LC50 Rat > 800 mg/cu m/4H
Dermal LD50 Rabbit > 3 g/kg
Calcium carbonate Not established
810564PM Page 5 of 6
11-20-2001
MATERIAL SAFETY DATA SHEET
Epoxy resin Not established
Bisphenol A Oral LD50 Ret = 3250 mg/kg
Dermal LD50 Rabbit = 3 ml/kg
Iron oxide Not established
Aromatic amine Not established
Crystalline silica Not established
TOXICOLOGY SUMMARY: No additional health information available.
SECTION 12: ECOLOGICAL INFORMATION
OVERVIEW: No ecological information available
No levels of volatile organic compound emissions are expected at ambient temperatures and pressure. Depending
on powder chemistry, however, higher levels of VOC and low molecular weight hydrocarbons may be emitted at
cure temperatures. Emissions data are best developed by monitoring actual plant conditions.
SECTION 13: DISPOSAL CONSIDERATIONS
To the best of our knowledge, this product does not meet the definition of hazardous waste under the U.S. EPA
Hazardous Waste Regulations 40 CFR 261. Disposal via incineration at an approved facility is recommended.
Consult state, local or provincial authorities for more restrictive requirements.
SECTION 14: TRANSPORTATION INFORMATION
Consult Bill of Lading for transportation information.
SECTION 15: REGULATORY INFORMATION
INVENTORY STATUS
U. S. EPA TSCA: This product is in compliance with the Toxic Substances Control Act's
Inventory requirements.
CANADIAN CEPA DSL: This product is in compliance with the Canadian Domestic Substance List
requirements.
If you need more information about the inventory status of this product call 651-236-5858.
TSCA Section 12(b) - Export Notice Requirements
This product contains a chemical substance that is currently on the EPA's Section 12(b) Export List. Contact the
company Global Regulatory Group at 651/236-5858 for the identity of the Section 12(b) chemical(s).
FEDERAL REPORTING
EPA SARA Title III Section 313
Unless listed below, this product does not contain toxic chemical(s) subject to the reporting requirements of
section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR part
72. EPA has advised that when a percentage range is listed the midpoint may be used to fulfill reporting
obligations.
Chemical Name CAS# %
4,4'-Isopropylidenediphenol 80-05-7 1- 5
810564PM Page 6 of 6
11-20-2001
MATERIAL SAFETY DATA SHEET
WHMIS STATUS: Unless listed below, this product is not controlled under the Canadian Workplace Hazardous
Materials Formation System.
D2B D2A
STATE REPORTING
This MSDS is not prepared for distribution in California.
SECTION 16: ADDITIONAL INFORMATION
This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health
Administration (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the Canadian Workplace
Hazardous Materials Information System (WHMIS).
Prepared by: The Global Regulatory Department
Phone: 651-236-5842
The information and recommendations set forth herein are believed to be accurate. Because some of the
information is derived from information provided to the H.B. Fuller Company from its suppliers, and because the
H.B. Fuller Company has no control over the conditions of handling and use, the H.B. Fuller Company makes no
warranty, expressed or implied, regarding the accuracy of the data or the results to be obtained from the use
thereof. The information is supplied solely for your information and consideration, and the H.B. Fuller Company
assumes no responsibility for use or reliance thereon. It is the responsibility of the user of H.B. Fuller Company
products to comply with all applicable federal, state and local laws and regulations.
|