TRIM MIST MATERIAL SAFETY DATA SHEET
5030
Gerber FastFact #
Gerber Service
Supplied by:
November 27, 2001
Last Modified:
This document provides material safety information for TRIM MIST.
Summary:
1. MATERIAL AND MANUFACTURER IDENTIFICATION
Product Name TRIM MIST
Material Type Water Miscible cutting and grinding fluid
concentrate
Classification/synonym(s) Chemical fluid/Synthetic fluid
Product Use Coolant and lubricant in metal removal process
Manufacturer address Master Chemical Corporation
510 West Boundary
Perrysburg, OH 43551-1263
Emergency telephone 419-874-7902 Fax 419-874-0684
2. REGULATORY INFORMATION
Department of Transportation DOT Hazard Class: None
TRIM MIST is not classified as a hazardous material by
DOT
Resource Conservation and Recovery Act EPA Hazardous Waste Number(s): None
TRIM MIST is not classified as a hazardous waste by EPA
Toxic Substances Control Act All TRIM MIST ingredients are listed on the TSCA
Inventory of Chemical substances.
Superfund Amendments and TRIM MIST does not contain any SARA Title II section
Reauthorization Act of 1986 302/304 Extremely Hazardous Substances or Section 313
Toxic Chemicals.
Page 2 of 4
Gerber Scientific Products Inc.
3. INGREDIENT INFORMATION
OSHA ACGIH TLV OTHER LIMITS
COMPONENT PEL RECOMMENDED CAS # % RANGE
The exact identities and percentages of the raw materials used in TRIM MIST are trade secrets. This
information is being withheld as provided for in the Occupational Safety and Health Administration's Hazard
Communication Rule (CFR 1910.1200).
4. PHYSICAL DATA
Boiling point (at 769 mm Hg) 217癋 (103癈) Specific gravity (H20=1) 1.06
Vapor pressure (psi) <1 Percent volatiles by volume 72.81%
Vapor density (Air=1) Not determined Evaporation rate 1
(butyl acetate +1)
Solubility in water 100% pH of concentrate 8.3
Flash point (test method): None (COC & TCC) Flammable limits: Not determined
Extinguishing Media As appropriate for the surrounding fire: water (flood with water), dry chemical,
CO2 or "alcohol" foam
Special Fire fighting procedures: None Unusual fire and explosion hazards: None
Page 3 of 4
Gerber Scientific Products Inc.
6. HEALTH HAZARD DATA
Threshold limit value: None established by ACGIH or OSHA
Acute effects of overexposure Eye Contact Transient irritation
Skin contact Possible defatting, nonirritant,
nonsensitizer
Inhalation Nontoxic
Ingestion Nontoxic
Skin Absorption Nontoxic
Chronic effects of overexposure None currently known
Product/Ingredients listed as NTP Annual report - NO IARC Monographs - NO
carcinogen or potential OSHA - NO
carcinogen?
Signs and symptoms of exposure None
Medial conditions generally None known
aggravated by exposure
Emergency & first aid Eyes Flush immediately with cool,
clean water for at least 15
Skin minutes
Wash with mild soap and warm
Inhalation water
Ingestion If large quantities are ingested,
contact a physician. In every
case get medical attention as
required.
7. REACTIVITY DATA
Stability: Stable Conditions to avoid: None
Incompatibility: Strong oxidizers, acids and alkalis
(materials to avoid)
Hazardous combustion or decomposition products: Thermal decomposition (fire) may produce CO, CO2,
COX
Hazardous polymerization: Will not occur Conditions to avoid: None
8. SPILL OR LEAK PROCEDURES
Steps to be taken if material is released or spilled Mop up or use dry absorbent
Waste disposal material Acid-alum split
Refer to Data and Information sheet for suggested
procedure.
Page 4 of 4
Gerber Scientific Products Inc.
9. SPECIAL PROTECTION INFORMATION
Respiratory protection: None
(specific type)
Ventilation Local Exhaust Not normally required
Mechanical (general) General room ventilation should
be sufficient
Special None
Other None
Protective gloves: None
Other Protective equipment: Safety glasses
10. SPECIAL PRECAUTIONS
Precautions to be taken in handling and storing Refer to Data & Information Sheet or container
labels
Other precautions This product contains amine. Do not add nitrite or
other nitrosating agents to this product due to the
potential for nitrosamine formation.
Date of preparation June, 1991
TRIM is a registered trademark of Master Chemical Corporation
This information is given in good faith and Believed current as of the date of this MSDS. Because conditions of use are beyond our control, no
guarantee, representation or warranty expressed or implied is made. Consult MCC for further information.